HomeMy WebLinkAboutCity of Tamarac Resolution R-2013-124f
T R 12430
Page 1
November 18, 2013
CITY OF TAMARAC, FLORIDA
RESOLUTION *NO. R- 2013 -
A RESOLUTION OF THE CITY COMMISSION OF THE
CITY OF TAMARAC, FLORIDA AUTHORIZING THE
PURCHASE OF TWO (2) 2014 HORTON MODEL 623
ADVANCED LIFE SUPPORT RESCUE VEHICLES BUILT
ON A 2014 INTERNATIONAL 430OLP CREW CAB
CHASSIS, HORTON EMERGENCY VEHICLES COMPANY,
FROM HALL -MARK FIRE APPARATUS, INC., UNDER THE
FLORIDA FIRE CHIEFS' ASSOCIATION, FLORIDA
SHERIFFS' ASSOCIATION & FLORIDA ASSOCIATION OF
COUNTIES BID AWARD ANNOUNCEMENT NO. #11-10-
1202, SPECIFICATION 02, THROUGH THE USE OF A
FINANCIAL LEASE, AT A TOTAL COST NOT TO EXCEED
$546,916-00; AUTHORIZING THE DISPOSAL OF TWO (2)
OUTDATED RESCUE VEHICLES; PROVIDING FOR
CONFLICTS; PROVIDING FOR SEVERABILITY; AND
PROVIDING FOR AN EFFECTIVE DATE.
WHEREAS, Tamarac Fire Rescue provides fire rescue services including fire
suppression, response to vehicle and industrial accidents and emergency medical
services to the residents, businesses and visitors in the City; and
WHEREAS, the City of Tamarac desires to maintain the highest possible level of
emergency medical services transportation; and
WHEREAS, the purchase of two new advanced life support rescue vehicles will
greatly assist the Tamarac Fire Rescue Department in maintaining apparatus reliability,
response times and meeting the desired level of service for our citizens, businesses and
visitors; and
WHEREAS, in 2012, Tamarac Fire Rescue formed a cross functional Rescue
Committee which consisted of Captains, Lieutenants, Firefighter -Paramedics, a
Battalion Chief, a Division Chief, a City Safety Committee Representative and the Fleet
T R 12430
Page 2
November 18, 2013
Supervisor to design a rescue vehicle that is safe, functional and incorporates the
requirements of Fire Rescue, attached hereto as Exhibits A and A1, and Fleet
Management, attached hereto as Exhibit B; and
WHEREAS, the Committee thoroughly evaluated several manufacturers including
Braun, MedTec, Osage, and Wheeled Coach and recommended to pursue designs from
Horton Emergency Vehicles; and
WHEREAS, Horton Emergency Vehicles through Hall -Mark Fire Apparatus has
provided the City of Tamarac a quotation, attached hereto as Exhibit C based on Florida
Fire Chiefs' Association, Florida Sheriff's Association and the Florida Association of
Counties Bid Award Announcement No. #11-10-1 202 Specification #02, attached hereto
as Exhibit D with Fire Rescue and Fleet Specific options, attached hereto as Exhibit E;
and
WHEREAS, the Fire Chief and the Director of Financial Services find it to be in
the best interest of the City to acquire these rescue vehicles through a financial lease
arrangement; and
WHEREAS, funding for the rescue vehicles was approved in the biennial FY14-
15 budget; and
WHEREAS, the Fire Chief and the Purchasing and Contracts Manager
recommend the
purchase of two
Horton
rescue vehicles through Hall -Mark Fire
Apparatus, Inc. in
the amount not to
exceed
$546,916.00; and
WHEREAS, City Code §6-148 (E) allows the Purchasing Officer the authority to
utilize contract prices from other governmental agencies; and
WHEREAS, the City of Tamarac has available for disposal two (2) rescue
vehicles, a 2001 and 2004 Freightliner MedicMaster (Unit # 338 and 344); and
TR 12430
Page 3
November 18, 2013
WHEREAS, City Code §6-156.1 permits the disposal of Surplus Stock; and
WHEREAS, the City Commission of the City of Tamarac deems it to be in the
best interest of the citizens and residents of the City of Tamarac to acquire the two
Horton Model 623 advanced life support rescue vehicles through Hall -Mark Fire
Apparatus, Inc. in an amount not to exceed $546,916.00 through the use of a financial
lease.
NOW THEREFORE BE IT RESOLVED BY THE CITY COMMISSION OF THE
CITY OF TAMARAC, FLORIDA:
Section 1:
The foregoing "WHEREAS" clauses are HEREBY ratified and
confirmed as being true and correct and are HEREBY made a specific part of this
Resolution. All Exhibits attached hereto are incorporated herein and made a specific
part hereof..
Section 2: The appropriate City Officials are HEREBY authorized to approve the
lease purchase of two (2) 2014 Horton Model 623 advanced life support rescue vehicles
from Hall -Mark Fire Apparatus, Inc. utilizing the Florida Fire Chiefs' Association, Florida
Sheriff's Association and the Florida Association of Counties Bid Award Announcement
11-10-1202 Specification #02, through the use of a financial lease arrangement, with the
City owning the rescues at the end of the lease term (five years) with subsequent
Agreements if necessary, pending legal review and approval between the City of
Tamarac and Hall -Mark Fire Apparatus, Inc. in an amount not to exceed $546,916-00.
Section 3: The appropriate City Officials are HEREBY authorized to approve the
disposal of disposal two (2) rescue vehicles, a 2001 and 2004 Freightliner MedicMaster
(Unit # 338 and 344) under City -Code §6-156. 1.
Section 4:
All Resolutions or parts of Resolutions in conflict herewith are
HEREBY repealed to the extent of such conflict.
Section 5:
T R 12430
Page 4
November 18, 2013
If any clause, section, other part or application of this Resolution is
held by any court of competent jurisdiction to be unconstitutional or invalid, in part or in
application, it shall not affect the validity of the remaining portions or applications of this
Resolution.
Section 6:
This Resolution shall become effective immediately upon its passage
and adoption.
PASSED, ADOPTED AND APPROVED this day of , 2013.
BETH TALABIS20
MAYOR
ATTEST:
IcPATRICIA TEUFEL, CMC
CITY CLERK
RECORD OF COMMISSION VOTE:
MAYOR TALABISCO
DIST 1: COMM. BUSHN LL
DIST 2: VICE MAYOR GOMEZ e,,,e-a
DIST
3:
COMM.
GLASSER
DIST
4:
COMM.
DRESSLE
HEREBY CERTIFY THAT I HAVE
APPROVED THIS RESOLUTION
AS TO FORM
SAMUEL S. GOREN
CITY ATTORNEY
TR 12430- Exhibit A
Horton
� EMERGENCY VEHICLES
Aell-Mark Fire-3031 NW 27W Ave --Ocala, FL 34475
CATEGORIES:
A
Chassis
B
Body Connection Pass Thru Type
BH
Chassis Accessories
BL
Chassis Electrical
C
Conversion Model
CB
Module Body Modifications
D
Module Body Hardware
E
Paint and Striping
TAMARAC FIRE RESCUE
F
Cabinet Doors, Handles and Hardware
6000 HIATUS ROAD
TAMARAC, FL 33321
G
Interior Colors
STEVE STILL WELL
H
Interior Cabinets, Streetside
Year: 2014
I
Interior Cabinets, Curbside
Chassis: Navistar 10811
J
Front Wall Cabinets
Type: MED
Model: 623
K
Interior Accessories and Trim
Rev 2 Print Features 11747
L
Cot Mount, and Patient Handling
M
Warning Systems, Visual
MN
Warning Systems, Audible
O
Lights, Non Emergency
P
Electrical Power Group
Q
Heat, Ventilation, Air conditioning
R
Console, Radio, and communications
T
Oxygen and Suction
U
Lettering and Graphics
Z
Other
Prepared By: Michael Dav
TR 12430- Exhibit A
TAMARAC FIRE RESCUE
6000 HIATUS ROAD
TAMARAC, FL 33321
STEVE STILLWELL
- =Horton
1111110 ■MMOB,►VE«CLE$
Selected Feature List
Year:
Chassis:
Model:
Praposal Total
11747
2014
Navistar 108"
623
AB Horton Emergency Vehicles Feature List 1
I'm NAVISTAR CHASSIS
AIN62514 0 1 CHASSIS, 2014 NAVISTAR 430OLP9 1089' CIA
811912013
The chassis required to complete the ambulance conversion shall be
supplied by Horton. Chassis ordered with OEM air rides will include
a Horton installed air tank drain line, running from the tank(s) to
the bottom side of the rub rail.
Reference quote #: 11234-04
Horsepower: 260
AJNSPICO 1 1 CHASSIS INTERIOR COLOR SHALL BE GRAY
ASP00100 0 1 CHASSIS SPECIAL INSTRUCTION
1212712012 ! ! ! SUPPLY AND INSTALL AN "ECHO -VISION" REAR COLLISION AVOIDANCE SYSTEM.
LOCATE THE (2) SENSORS ON REAR OF VEHICLE. INSTALL CONTROL UNIT IN FRONT
CONSOLE PER DRAWING.
BH021000
BH02J000
CHASSIS MODIFICATIONS, HARDWARE AND ACCESSORIES
0 1 TIRE SIZE, 22.5199MEDIUM DUTY:
This vehicle is specified to have 22.5" tires.
41212012
0 1 CHASSIS IS EQUIPPED WITH AIR BRAKES:
41212012
This vehicle is specified to have air brakes. Note that proper tire
clearances are allowed.
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:16 PM Rev 2 Page 2 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE Selected Feature List 11747
6000 HIATUS ROAD Year:
2014
TAMARAC, FL 33321 =Hor%on
STEVE STILLWELL 1111EMEMEMYVEHICMS Chassis: Navistar 108"
Model: 623
Option Std Otv Header/Descrivdon/Data Proposal Total
BH03A000 1 1 MUD FLAPS: front
Install rubber mud flaps behind each front tire.
BH03B000 1 1 MUD FLAPS: rear
Install individual rear mud flaps behind each set of rear wheels.
BH04B000 0 1 NAVISTAR EQUIPPED W/VERTICAL EXHAUST
The chassis specified above is to include a vertical exhaust.
41212012
BH04G000 0 1 CHASSIS HORSEPOWER RATING IS 260HP OR HIGHER
The chassis specified above will have a 411 raised cab height.
Note: 300 hp V8 Maxxforce 7 engines do not require raised cab.
41212012
BH060000 0 1 REAR DOCK BUMPERS
Two rubber dock bumpers shall be bolted to the rear step end caps
for protection when backing.
41212012
BH11 DQ00 0 1 ENERGY ABSORBING REAR FLIP -UP STEP:
Install an energy absorbing rear step/bumper assembly. The center
section of the step will flip up for cot loading. When flipped down
the center section must be held down so as not to rattle while the
vehicle is in motion.
41212012
BH2OT000 0 1 CHROME TURNOUT FOR VERTICAL EXHAUST
A chrome turnout shall be installed on the vertical exhaust of
medium duty chassis.
41212012
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:16 PM Rev 2 Page 3 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE Selected Feature List l l 747
6000 HIATUS ROAD Year: 2014
TAMARAC, FL 33321 m
STEVE STILL WELL
� ■Hf'tOrl Chassis: Navistar 108"
Model: 623
Oyd on Std Otv Header/Description/Data Proposal Total
BH26J000 0 1 FUEL TANK COVERS, DIAMOND PLATE FOR FOUR -DOOR CABS
Diamond plate step well covers shall be installed on both the curb
and street side cab step wells. The covers shall be made of
.125"thick polished diamond tread plate with a minimum 3003-H14
alloy. The cover shall include a pull out tray for chassis
batteries. The covers shall sized appropriately for a four -door cab.
111712013 ! ! ! INSTALL A DIAMOND PLATE COMPARTMENT BEHIND THE REAR PORTION OF THE
PASSENGER ' S AND DRIVER SIDE TANK COVER. COMPARTMENT TO BE AS LARGE AS
POSSIBLE AND
HAVE A HINGE DOWN DOOR WITH (2) LOCKING LEVER LATCHES. BATTERIES TO BE IN
REAR PORTION OF DRIVER ' S SIDE TANK COVER.
! ! ! INSTALL LED STRIP LIGHTS ON THE TANK COVERS TO LIGHT UP THE STEPS
WHEN THE CAB DOORS ARE OPENED. USE TECNIQ FLAT STYLE. EXACT TBD AT PRE -
BUILD.
r r ! TOP STEP TO BE WIDER THAN PREVIOUS UNITS.
.. REFERENCE VEHICLE #15394
BH320R00 1 1 AIR SUSPENSION SWITCH: dump override
A switch will be installed where specified, to override the
automatic dump feature activated by the left rear patient
compartment entry door.
41212012 Switch Locate:
RIGHT SIDE REAR ENTRY DOOR, JUST ABOVE HANDLE.
BH34AC00 0 1 FRONT STABILIZER BAR: INT 430OLP, ROADMASTER
A Roadmaster front stabilizer bar shall be installed on the
International 430OLP chassis.
41212012
BH34AD00 0 1 REAR STABILIZER BAR: INT 430OLP, ROADMASTER
A Roadmaster rear stabilizer bar shall be installed on the
International 430OLP chassis.
41212012
BHSPDO06 1
BL26B000 1
1 MIRROR: OEM
The mirror set shall be OEM supplied, and installed by the chassis
manufacturer.
1 BACKUP ALARM RESET
Backup alarm to automatically reset to on if alarm was manually
canceled using -the control panel alarm cut-off switch (FL25) during
previous use.
1211012012 ! ! ! DELETE THE ABILITY TO CANCEL THIS ALARM.
Hall -Mark Fire Thursday, November 07, 2013 1 hint Features
Michael Day 10: 09:16 PM Rev 2 Page 4 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE Selected Feature List
6000 HIATUS ROAD
Year:
TAMARAC FL 33321 MHO n
STEVE STILLWELL •MEMEN"YEHICLM Chassis:
Model:
ODtion 5td ON Header/Descriation/Data Prop sal Fora
BL26J000 0 1 REVERSE CAMERA WITH WINDSHIELD MOUNTED MONITOR
Install a Voyager VCCS150 backup camera over the rear doors. Install
a Voyager AOM562HD 5.6" OR 7" LCD screen in the cab upper windshield
area. Wire to activate when the vehicle is placed into reverse.
111712013 ! ! ! INSTALL (2) BULLET CAMERAS FOR BLIND SPOT MONITORING. LOCATE ONE ON
THE STREETSIDE AND ONE CURBSIDE FORWARD CAB DOORS IN THE LOWER
FORWARD POSITION.
! ! ! CAMERAS TO ACTIVATE WITH THE RESPECTIVE TURN SIGNAL.
INSTALL MONITOR CENTER OF DASH WITH ADJUSTABLE MOUNTING BRACKET. EXACT
CONFIGURATION AND PLACEMENT TO BE COMPLETED AT PRE -BUILD.
! ! ! SYSTEM REQUIRES A VOYAGER #AOM7694 MONITOR WITH (4) INPUTS.
BL32A000 1 1 OEM AM/FM/CD PLAYER SHALL BE PROVIDED BY THE OEM
MANUFACTURER
OEM AM/FM/CD player shall be provided by the OEM manufacturer on all
Horton supplied chassis.
Note: This option applies only to chassis supplied by Horton. Chassis
supplied by either the customer or the dealer must be ordered with
this feature from the chassis OEM.
BL35BWNO 0 1 BUMPER WANDS, LIGHTED FOR NAVISTAR
Lighted bumper wands shall be installed at the outer edges of the
chassis front bumper.
41212012
BSP00001 0 1 SPECIAL INSTRUCTION, CHASSIS MODIFICATION HARDWARE &
ACCESSORIES
111712013 ! ! ! SUPPLY AND INSTALL A DUAL DYNAMICS CROSSFIRE DUALTM TIRE PRESSURE
EQUALIZATION AND MONITORING SYSTEM, 105 PSI, ONE PER PKG. (CF105STABT)
CONVERSIONS
11747
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10: 09:16 PM Rev 2 Page 5 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE
6000 H/A TUS ROAD
TAMARAC, FL 33321
STEVE STILLWELL
• . •
=HOMon
M MOM04 CY VEHICLES
Selected Feature List
Year:
Chassis:
Model:
Proposal Total
CA615000 0 1 CONVERSION MODEL: 623 INTERNATIONAL PASS -THROUGH:
CA615001
MINIMUM BODY DIMENSIONS:
(Exterior)
-Height: 91"
-Width: 96"
-Length: 173"
(Interior)
-Height: 72"
-Aisle 20"
-Width: 2011(from edge of
bench riser)
cot in wall position to squad
-Length: 169"
OVERALL DIMENSIONS (Including Chassis, Module and Step):
-Height: 110" (to top of vent)
-Width: 100"
-Length: 296"
111712013 !!! BODY TO BE 177" WITH A 112" CA.
1 1 623 STREETSIDE FORWARD:
Clear Door Opening: 18.7" wide x 80.6" high
Actual Compartment 21.4" wide x 83.6" high x 21.5"
This area shall be accessed through a single outside hinged door.
The compartment shall house the vehicle's primary 02 cylinder. The
compartment shall be vented to the outside.
112912013 ! ! ! INSTALL A COMPARTMENT THAT IS 21 " HIGH ABOVE THE 02 COMPARTMENT.
THIS COMPARTMENT WILL BE USED FOR STORAGE OF ALL ADD ON ELECTRICAL
EQUIPMENT, BREAKER BOXES, BATTERY CHARGER, VACUUM PUMP AND AIR COMPRESSOR.
! SUPPLY AND INSTALL A "D" BOTTLE STORAGE BOX TO FIT (4) BOTTLES.
INSTALL ON THE TOP OF THE ADJUSTABLE SHELF. STORAGE TO BE 5" ID.
! ! ! ! ! HORTON ENGINEERING DOES NOT RECOMMEND THE ABOVE STORAGE.
0 1 COMPARTMENT HEIGHT Modify: first, street side
cb040000 The height of the standard compartment for this model shall be
modified. This is the first street side compartment height
modification and shall include affected modifications to the
interior cabinet.
511512012 Height Modification: REDUCE 22.00 " TO ALLOW FOR INSTALLATION OF
ADDITIONAL ELECTRICAL COMPARTMENT ABOVE THE STREETSIDE FORWARD COMPARTMENT.
0 1 SHELF FOR LED LIGHTED VERTICAL COMPARTMENT
dr081000 A diamond plate adjustable shelf shall be installed in the following
location.
812112012 Locate: ABOVE 02 SYSTEM
11747
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:18 PM Rev 2 Page 6 of 38
0
TAMARAC FIRE RESCUE
6000 HIATUS ROAD
TAMARAC, FL 33321
STEVE STILLWELL
TR 12430- Exhibit A
Selected Feature List 11747
— =Horton
■EMERGO4CYVENCLEs
wd on/Data Pia
Year:
Chassis:
Model:
Total
0 1 OXYGEN BOTTLE BRACKET: Zico OTS electric
tr101e000 Electric operated oxygen bottle mount for cylinder loading and
securing. Controls to be mounted on the in side of the compartment
door.
51712012 Bottle size: "M"
Compartment: STREETSIDE FORWARD
(NOTE --COMPARTMENT DEPTH MUST BE A MINIMUM OF 16" FOR THE BRACKET TO WORK
PROPERLY) .
CA615002 1 1 623 STREETSIDE INTERMEDIATE:
Clear Door Opening: 51.8" wide x 39.8" high
Actual Dimensions: 55.5" wide x 43"high x 21.5"
This area shall be accessed through double, outside hinged doors.
Both doors shall have exterior door handles and latching devices.
811912013 ! ! ! SUPPLY AND SHIP LOOSE (3) ZICO #SC-50-H-6-SF WITH PHS STRAP ON THE
BACK WALL OF COMPARTMENT. THESE ARE TO BE SPACED EVENLY.
0 1 COMPARTMENT WIDTH Modify: first, street side
cb04Ow00 The width of the standard compartment for this model shall be
modified. This is the first street side compartment width
modification and shall include affected modifications to the
interior cabinet.
812112012 Width Modification: INCREASE 4 " DUE TO ADDITIONAL BODY LENGTH
0 1 SHELF FOR LED LIGHTED DOUBLE DOOR COMPARTMENT
dr091b00 A diamond plate adjustable shelf shall be installed in the area
listed below.
112912013 LOCATE: UPPER PORTION OF COMPARTMENT ABOVE THE BOTTLE BRACKETS
! ! ! SHELF TO BE STANDARD.
CA615004 1 1 623 STREETSIDE REAR:
Clear Door Opening: 32" wide x 39.8" high
Actual Dimensions: 37.4" wide x 43" high x 21.5"
This area shall be accessed through double, outside hinged doors.
Both doors shall have exterior door handles and latching devices:
0 2 SHELF FOR LED LIGHTED VERTICAL COMPARTMENT
dr081000 A diamond plate adjustable shelf shall be installed in the following
location.
511512012 Locate: SPACED EVENLY
CA615005 1 1 623 CURBSIDE REAR:
Clear Door Opening: 25" wide x 80.6" high
Actual Dimensions: 29.6" wide x 83.6" high x 21.5"
This area shall be accessed through a single outside hinged door
811912013 ! ! ! INSTALL A BACKBOARD RETENTION. BAR IN UPPER REAR PORTION, APPROX 8 "
FROM COMPARTMENT CEILING.
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:21 PM Rev 2 Page 7 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE
6000 HIATUS ROAD
TAMARAC, FL 33321
STEVE STILLWELL
• . •
- =Horton
OEwASWO CY VEHICLM
Selected Feature List
Year:
Chassis:
Model:
_Proposal Total
0 3 SHELF FOR LED LIGHTED VERTICAL COMPARTMENT
dr081000 A diamond plate adjustable shelf shall be installed in the following
location.
811912013 Locate: BETWEEN DIVIDER AND RIGHT WALL WITH BOTTOM SHELF INSTALLED 4 0 "
FROM FLOOR OF COMPARTMENT
Locate: FIXED SHELF LOCATED 10" FROM FLOOR, LEFT SIDE OF DIVIDER
0 1 DIVIDER FIXED, VERTICAL COMPARTMENT
dr11a000 Install a 16" deep fixed vertical divider shall be installed in the
location listed below. (Divider material is to match the compartment
material)
812112012 Locate: 12" FROM RIGHT WALL
0 1 ROK BACKBOARD STRAP
dr12a000 Install a ROK backboard strap in the designated backboard
compartment.
41212012
CA615006 1 1 623 CURBSIDE FORWARD:
Clear Door Opening: 22.1" wide x 83.6" high
Actual Dimensions: 26.7" wide x 86.6" high x 30"
This area shall be accessed through a single outside hinged door and
from an opening located on the curb side forward wall. The area
shall be primarily used for storage of customer furnished jump kits.
1211012012
CAB93AFO 0 1 KKK-A-1822F CERTIFICATION LABEL
The vehicle shall have weight/payload, electrical load and KKK-A-
1822F certification stickers installed in the 02 compartment.
41212012
B BODY MODIFICATIONS/OPTIONS
CB030000 0 4 MODULE HEAD ROOM, INCREASE FROM STANDARD (PER INCH)
The standard module body headroom shall be increased from standard
per the quantity listed below. The quantity represents inches and
must be in increments of 2".
41212012 Headroom Required: 76.00"
11747
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:24 PM Rev 2 Page 8 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE
6000 HIATUS ROAD
TAMARAC, FL 33321
STEVE STILLWELL
• . •
MENEAGENCY VEHICLES
Selected Feature List
Year:
Chassis:
Model:
Proposal Total
CB06SX00 0 1 DOUBLE STEP CURBSIDE ENTRY 6" DROP SKIRT
The curbside skirt, forward of the rear wheel well shall be dropped
6 inches. Two integral ALD steps within the side patient door step
well shall be available upon opening the side door for easier and
lower access to the patient compartment.
41212012
CB06SX10 0 1 STREETSIDE OF BODY LOWERED 6" FROM STANDARD
The street side of the body forward of the rear wheel well shall be
lowered 6" from standard.
41212012
CB09SA00 1 1 PATIENT AREA SOUND PROOFING/ACOUSTIC ENHANCEMENT
PACKAGE
Install standard sound control package.
CBSP0001 0 1 SPECIAL INSTRUCTION, BODY MODIFICATIONS
811912013 ! 1.1 SUPPLY AND INSTALL (3) CAST PRODUCTS SCBA STORAGE ACCESS DOORS AND
TUBES WITH NON LOCKING STYLE DOORS AS FOLLOWS
j 1) CURBSIDE REAR
(1) S TREE T S IDE FORWARD
(1) STREETSIDE REAR
SEE DRAWING.
r ► MODIFY TUBE STRUCTURE AND WHEEL
INSTALLATION. NOTE STORAGE BELOW CPR
! ! ! INSTALL RIBBED RUBBER MATTING I
TUBES. GLUE RUBBER MATTING DOWN SO I
REMOVED.
N
HOUSES AS NEEDED FOR THIS
SEAT.
THE BOTTOMS OF THE BOTTLE STORAGE
T WILL NOT SLIDE OUT WHEN BOTTLES ARE
r r ! CURBSIDE WHEEL HOUSE TO EXTEND TO REAR COMPATMENT .
CBSP0002 0 1 SPECIAL INSTRUCTION, BODY MODIFICATIONS
111712013 ! ! ! INSTALL A FLAT ALUMINUM COMPARTMENT THROUGH THE CENTER OF THE REAR
DIAMOND PLATE RISER PER DRAWING. COMPARTMENT TO BE AS LARGE AS POSSIBLE.
INCLUDE A HINGE -DOWN DIAMOND PLATE DOOR WITH A SINGLE LOCKING D-RING STYLE
HANDLE.
! ! ! INCLUDE "DOOR OPEN" SENSOR FOR INTELLIPLEX WARNING.
! ! ! COMPARTMENT DOES NOT INCLUDE POWER DOOR LOCK OR LIGHTING.
CBSP0003 0 1 SPECIAL INSTRUCTION, BODY MODIFICATIONS
812112012 ! ! ! INSTALL A COMPARTMENT THAT IS 21 " HIGH ABOVE THE 02 COMPARTMENT.
THIS COMPARTMENT WILL BE USED FOR STORAGE OF ALL ADD ON ELECTRICAL
EQUIPMENT, BREAKER BOXES, BATTERY CHARGER, VACUUM PUMP AND AIR
COMPRESSOR. INCLUDE PERKO VENT IN COMPARTMENT DOOR.
11747
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:24 PM Rev 2 Page 9 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE
6000 HIATUS ROAD
TAMARAC, FL 33321
STEVE STILLWELL
• . •
— =Horton
■M►,►ENCLES
CBSP0004 0 1 SPECIAL INSTRUCTION, BODY MODIFICATIONS
Selected Feature List
Year:
Chassis:
Model:
Proposal Total
812112012 ! ! ! THIS BODY TO BE 4. 00" LONGER BETWEEN THE CAB AND REAR WHEELS. THE
ADDITIONAL LENGTH IS TO BE ADDED TO THE INTERMEDIATE COMPARTMENT ON
STREETSIDE AND BETWEEN THE REAR OF THE SIDE ACCESS DOOR AND THE FORWARD
END OF THE WHEELHOUSE ON CURBSIDE.
CBSP0005 0 1 SPECIAL INSTRUCTION, BODY MODIFICATIONS
1212712012 ! ! ! MODIFY BODY AS NECESSARY FOR ZIAMATIC AUTOMATIC STEP AT SIDE ENTRY
DOOR PER DH280000.
CBSP0006 0 1 SPECIAL INSTRUCTION, BODY MODIFICATIONS
91712012 ! ! ! REINFORCE PATIENT CEILING AND BULKHEAD WALL AS NECESSARY FOR INSTALL
OF MEDVAULT UNIT OVER PASS THROUGH PER DRAWING.
CBSP0007 0 1 SPECIAL INSTRUCTION, BODY MODIFICATIONS
1211012012 ! ! ! REINFORCE PATIENT COMPARTMENT FLOOR FOR HORTON TO INSTALL CUSTOMER
SUPPLIED STRYKER POWER LOAD SYSTEM.
CBSP0008 0 1 SPECIAL INSTRUCTION, BODY MODIFICATIONS
111712013 ! ! ! CURBSIDE WHEEL WELL COMPARTMENT/PULL OUT DRAWER
! ! A COMPARTMENT SHALL BE CONSTRUCTED ABOVE THE CURBSIDE WHEELHOUSE. THE
DOOR FOR THIS COMPARTMENT IS TO BE FIXED TO THE FACE OF A SLIDE -OUT TRAY
HOUSED WITHIN THE COMPARTMENT. INSTALL ACCURIDE SLIDES ON TRAY. THIS
COMPARTMENT IS TO BE ACCESSIBLE FROM BOTH INSIDE AND OUTSIDE.
CBSP0009 0 1 SPECIAL INSTRUCTION, BODY MODIFICATIONS
111412013 ! ! ! NOTE SIDE SCENE LIGHTS WHEN INSTALLING BODY TUBES.
D MODULE BODY HARDWARE
DG05C100 0 2 PRIVACY WINDOWS, REAR MODULE BODY ENTRY DOORS
The rear module entry doors shall have solid windows.
shall have dark privacy glass. The windows shall meet
standards. No films are to be used.
811912013 ! ! ! THESE ARE TO BE SLIDING PRIVACY WINDOWS.
The windows
FMVSS glazing
11747
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:24 PM Rev 2 Page 10 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE
6000 HIATUS ROAD
TAMARAC, FL 33321
STEVE STILL WELL
• , •
Selected Feature List
mHomon
001 EMERGENCY VEHICLES
Pro
Year:
Chassis:
Model:
Total
DG06C200 0 1 PRIVACY WINDOW, SLIDING FOR SIDE ENTRY DOOR
The side entry door shall have a sliding window. The window shall
have dark privacy glass. The window shall meet FMVSS glazing
standards. No films are to be used.
812112012
DH03B000 1 1 MIRROR STAINLESS STEEL SPLASH SHIELDS
Install #8 mirror stainless splash shields on the lower front face
of the body just behind the cab access doors. These splash shields
are to be the same height as the diamond plate front corner guards.
(NOT AVAILABLE ON FORD "E" SERIES CHASSIS IN CONJUNCTION WITH EXTENDED
CORNER GUARDS)
DH04B000 0 1 MODULE BODY FENDERS: rubber
Rubber extruded fenders shall be installed around the rear wheel
well opening.
41212012
DH280000 0 1 ACCESS STEP, ZIAMATIC AUTOMATIC STEP:
Install a Ziamatic automatic step at the side entry door. The step
shall automatically fold out by electrical means when the side door
is opened. Requires two positions of a 3-position switch panel.
1211012012 REINFORCE STEPWELL WITH 0.25" ALUMINUM PLATE FOR INSTALLATION.
.. THIS IS TO BE A ZICO MODEL #VS-20-5
DH330000 1 1 REAR DOOR HOLD OPENS, GRABBER
Install chrome Cast Products "Grabber" style rear door hold opens.
(NOTE: HOLD OPENS MUST BE RELOCATED IF TELESCOPIC LIGHTS ARE ORDERED)
DL480000 0 1 ELECTRIC DOOR LOCKS: compartment
Install power activated door locks on all exterior compartment
doors. Locks to be activated by a switch at each patient area access
door. Locks may be overridden by a door key. A separate lock switch
will be located in the front radio console if option DL48D000 (wired
to OEM locks) is not selected.
41212012
11747
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10: 09:24 PM Rev 2 Page 11 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE
6000 HIATUS ROAD
TAMARAC, FL 33321
STEVE STILL WELL
.
—-I—lorton
E MOKIE CV VEHICLES
Selected Feature List 11747
Year:
Chassis:
Model:
Total
DL48A000 1 1 ELECTRIC DOOR LOCKS: access doors
Install power activated door locks on all patient area access doors.
Locks to be activated by a switch at each patient area door, and
controlled with the access door locks. Locks may be overridden by a
manual slide lever or by the door key. A separate lock switch will
be located in the front radio console if option DL48D000 (wired to
OEM locks) is not selected.
DL48B000 0 1 ELECTRIC DOOR SWITCH: concealed
Install a concealed switch on the exterior of the vehicle to operate
the power door lock circuit. Doors shall be wired to unlock only on
this circuit.
41212012 Locate:
GRILLE AREA
DL48D000 0 1 ELECTRIC DOOR LOCKS WIRED TO OEM SWITCHES
The module door locks and compartment locks (if ordered) are to be
wired to the chassis door lock switches.
1211012012
DLH41000 0 1 LICENSE PLATE BRACKET, POLISHED SURFACE MOUNT
A polished aluminum #LP0004 surface mounted license plate bracket
shall be installed in the designated location. A license plate
light will be incorporated into the top of the mounting bracket.
111712013 Locate:
DM100000 1 1 REFLECTORS:
EXACT LOCATION TBD AT PRE -BUILD
All patient compartment entry doors shall have red reflectors in the
lower corner.
DR22A000 0 1 MATEFLEX IN EXTERIOR COMPARTMENTS
Matef lex will be installed on the floor and shelves of all exterior
compartments.
41212012 Color:
BLACK
DR23A000 1 1 RUBBER COVERED WALLS IN BACKBOARD COMPARTMENT
The interior of the backboard compartment is to be covered with
rubber matting to protect equipment stored in this area.
41212012 Color:
Locate:
GRAY
CURBSIDE REAR COMPARTMENT
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:24 PM Rev 2 Page 12 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE
6000 HIATUS ROAD
TAMARAC, FL 33321
STEVE STILLWELL
• • •
n
Selected Feature List
=Horton
Pro
DSP00001 0 1 SPECIAL INSTRUCTION, MODULE BODY HARDWARE
811912013 ! ! ! INSTALL LICENSE PLATE SCREWS ON THE TIP
INSTALL LIGHT TO THE SIDE OF DOOR. LIGHT T
NEEDS TO BE AS THIN AS POSSIBLE SO FLIP UP
LIGHT.
DSP00002 0 1 SPECIAL INSTRUCTION, MODULE BODY HARDWARE
111712013 ! ! ! INSTALL ALUMINUM "C" CHANNEL RUB RAILS
STRIPE IN CENTER PORTION OF RUB RAILS.
E PAINT AND STRIPING
ED02F000 0 1 PAINT CHASSIS, medium duty
Year:
Chassis:
Model:
Total
O
DOWN DOOR ON THE REAR RISER.
BE TECHNIQ LED STYLE. LIGHT
PORTION OF BUMPER DOES NOT HIT
ILOS. INSTALL RED REFLECTIVE
The chassis cab shall be painted with the following special paint
color and paint code:
811912013 COLOR: RED OVER SILVER
NUMBER: SILVER -FLNA-91733
RED - FLNA-3225
!!! PAINT CHASSIS RED FROM WINDOW LINE UP.
PORTION OF CHASSIS TO BE SILVER. CHASSIS TO
.. SEE DRAWING.
ED050000 0 1 MODULE PAINT: other color
Paint MODULE special color
CHASSIS HOOD TO RED. LOWER
ARRIVE RED
112912013 PAINT COLOR: RED OVER SILVER
PAINT NUMBER: SILVER -FLNA-91733
RED - FLNA-3225
! ! ! UPPER PORTION OF BODY TO BE RED FROM APPROXIMATLEY
BODY LIGHTS UP. REMAINDER OF BODY TO BE SILVER.
! ! ! NOTE REAR OF VEHICLE TO BE DIAMOND GRADE MATERIAL
2 " BELOW THE UPPER
PER BELOW.
11747
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10: 09:24 PM Rev 2 Page 13 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE
6000 HIATUS ROAD
TAMARAC, FL 33321
STEVE STILL WELL
ED090000 0 1 STRIPE: custom
Special paint stripe
See drawing
Selected Feature List 11747
- =Hor'ton
MEME MOWY VEHICLE$
iyt on/Data Pro
Year:
Chassis:
Model:
I Total
811912013 ! ! ! CUSTOM BELTLINE STRIPE THAT STARTS JUST BEHIND CHASSIS FENDERS AND
INCLUDES A LARGE STEP UP ON FRONT FACE OF BODY PER DRAWING. STRIPE TO
WRAP REAR CORNER POSTS AND STOP.
1" BLACK SCOTCHLI TE
1" SILVER PAINT
6 " RED SCOTCHLI TE
1" SILVER PAINT
1" BLACK SCOTCHLI TE
INSTALL 1" BLACK SCOTCHLI TE AT PAINT BREAK ON CAB AND BODY.
! SEE DEALER SUPPLIED LAYOUT IN ELECTRONIC FILE.
ED20PS00 0 2 PAINT PANEL: sample
A painted test panel shall be prepared with the following paint
color and number, to confirm correct paint selection. The panel will
be mailed as designated.
811912013 NUMBER: SILVER -FLNA-91733
RED - FLNA-3225
! ! ! SAMPLES TO BE FURNISHED ON METAL ILO PAPER.
F.
ED5C0000 0 1 DIAMONDGRADE CHEVRONS -ENTIRE REAR
Install Diamondgrade chevron striping on the entire rear of the body
inboard of the corner posts and below the upper driprail.
811912013 Colors: 6" RED #983-72 AND FLUORESCENT YELLOW GREEN #983-23
! ! ! ILOS THE UPPER PORTION OF THE REAR DOORS TO BE ALL RED DIAMOND GRADE
AND LETTERING TO BE INSTALLED OVER THE DIAMOND GRADE MATERIAL.
F INTERIOR CABINET DOORS, HANDLES & HARDWARE
FE010000 1 1 FULL HEIGHT PULL HANDLES ON SLIDING PLEXIGLAS DOORS
All sliding cabinet doors to have full length pull handles.
FE01 FT00 1 1 LATCH, HINGED DOOR: Southco flush stainless steel pull style
Install stainless flush mount Southco pull latches on the hinged
interior cabinet doors.
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:24 PM Rev 2 Page 14 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE
6000 HIATUS ROAD
TAMARAC, FL 33321
STEVE STILL WELL
FE02A000
FE060000
- =Morton
= ■MEMOWY VMCM8
• , •
1 1 PLEXIGLAS COLOR: light tint
All Plexiglas doors to be light tint.
Selected Feature List 11747
Year:
Chassis:
Model:
Proposal Total
1 1 STAINLESS STEEL COUNTER TOPS (STANDARD)
Stainless steel pan formed counter tops shall be installed in the
patient area.
FE07A000 0 1 STAINLESS STEEL -INHALATION AREA WALLS:
The rear and side walls bordering the inhalation area are to be
covered with brushed stainless steel.
FE08A000
G
GF01 R000
41212012
0 1 STAINLESS STEEL -INHALATION PANEL:
41212012
The inhalation panel is to be fabricated from stainless steel. All
edges are to be filed.
INTERIOR COLORS, UPHOLSTERY AND SEATING
0 1 INTERIOR COLOR SCHEME: Custom
Interior colors are as follows:
1211012012 Floor
Risers:
Walls:
Cabinets:
Upholstery:
NO ACCENT STRIPE
LONCOIN FLECKSTONE BLACK ONYX
STAINLESS STEEL
WILSONART FASHION GRAY #D381
FASHION GRAY PAINT
SPRADLING ROGUE II FLINT GRAY
#150UV
#RU900
GF02M000 1 1 INSIDE CABINET FINISH: paint
The interior of all aluminum cabinets shall have a durable paint
finish. The painted surface shall be washable and non -absorbent.
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10: 09:24 PM Rev 2 Page 15 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE Selected Feature List
6000 HIATUS ROAD Year:
TAMARAC FL 33321 =Horton
STEVE STILL WELL IIIIIIII MMOMOW,► VERCMs Chassis:
Model:
ion Std ON Header/Descrintion/Data Proposal TotaI
GF02P000
GF030000
GF03A000
GF03C000
1 1 RISERS:
The interior of this vehicle is to contain no wood or.wood products.
The risers are to be made of reinforced structural composite board
covered with Formica per the color description. Formica will not
installed on the risers if stainless steel riser options are
selected.
Note: ,Riser thickness to be modified if option #PL27CP00 is ordered.
0 1 STAINLESS STEEL RISER, cabinet wall
Install stainless steel on cabinet wall riser. If
accent stripe is ordered the stainless steel will
edge of the stripe.
41212012
0 1 STAINLESS STEEL RISER, bench wall
Install stainless steel on squad bench riser.
41212012
a cabinet riser
stop at the bottom
0 1 STAINLESS STEEL LOWER DOOR PANELS
Finish lower section of inside patient compartment doors with
stainless steel. If an interior accent stripe is ordered the
stainless is to stop at the bottom of the stripe.
41212012
GK12D000 0 1 EVS CHILD SAFETY SEAT WITH 3-POINT SEAT BELT
Delete the standard attendant seat cushion. Install a high back
bucket seat with built in child seat restraints and 3-point occupant
restraint. The seat to be adjustable front to rear.
41212012
GK140000 1 1 SEAT BELTS:
Install standard seat belt package for use with HOPS.
1012312012 NOTE : DO NOT INSTALL 3-PT AT HEAD OF BENCH.
INTERIOR CABINETRY, STREET SIDE
11747
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:24 PM Rev 2 Page 16 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE
6000 HIATUS ROAD
TAMARAC, FL 33321
STEVE STILLWELL
PR
=Horton
MmERGEIdCV VEHICLES
Selected Feature List
Year:
Chassis:
Model:
Proposal Total
HK000000 1 1 LINEN CLOSET
Install a vertical storage cabinet behind the attendant seat. The
upper storage area shall house the primary electrical distribution
area. The lower section shall be used for miscellaneous storage.
Each area shall be accessed through hinged doors. The electrical
distribution area shall include a Southco key lock/latching device.
The entire cabinet shall be fabricated from aluminum and shall then_
be painted, unless otherwise specified.
111712013 ! ! ! INSTALL A 9 " HEADER SO KNOX BOX CAN OPEN.
! ! ! BOTTOM DOOR TO INCLUDE (2) STAINLESS STEEL VENTS.
HK001000 1 1 HOPS SYSTEM:
The unit is to be equipped with the HOPS system.
1212712012 Note: Deletion
of
the system along with
the selection of option #HK01A000
requires that
the
credit provided under
HK01B000 be deleted.
HK01 B000 1 1 STREETSIDE WALL WITH CPR SEAT
Street side wall to have CPR configuration.
SEE DRAWINGS
812112012 Configure: street side cabinets to be 18" deep.
! ! ! CUSTOM CABINET WALL PER DRAWING.
HK01 R000 0 2 LIFT UP CABINET FRAMES: street. -side
Fasten the Plexiglas door frame extrusion to a piano hinge secured
to the cabinet wall. The complete frame and doors shall hinge open
upward providing total access to the cabinet behind. The frame shall
be held open with gas charged cylinders and secured in the down
position with a sliding dead bolt.
812112012 Locate: BOTH UPPER CABINETS
HK02L000 0 1 STORAGE BENEATH THE CPR SEAT
A trimmed storage area shall be accessed by raising the hinged side
attendant seat base cushion.
812112012 ! ! ! NOTE LIMITED STORAGE DUE TO SCBA BODY TUBES.
HK03D000 0 1 PULL OUT DRAWER INSTALLATION IN MAIN CABINET WALL
Pull out drawer(s) shall be installed in the main cabinet wall at
the locations listed below.
811912013 Location: REAR WALL RECESSED INTO STREETSIDE REAR COMPARTMENT PER
DRAWING. FULL WIDTH OF CABINET.
11747
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:24 PM Rev 2 Page 17 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE
6000 HIATUS ROAD
TAMARAC, FL 33321
STEVE STILL WELL
= �HOmon
Selected Feature List
Year:
Chassis:
Model:
Proposal Total
HK17G000 0 1 SHARPES/WASTE STORAGE IN A TIP OUT DOOR IN MAIN CABINET
WALL
Install both sharps and waste containers on a tip -out door within
the main cabinet wall. The door shall be specifically located as
noted below.
511512012 Locate: FORWARD OF THE CPR SEAT PER DRAWING.
HSP00001
IA200000
IG070110
0 1 SPECIAL INSTRUCTION, STREETSIDE CABINETRY
111712013 ! ! ! FABRICATE AND INSTALL CABINET ABOVE THE CPR SEAT WITH HINGE UP
PLEXIGLASS DOOR PER DRAWING. CABINET TO BE 40 "w X 7 "h X FULL DEPTH. THIS
REQUIRES CUSTOM INSTALL DUE TO THE HEIGHT OF THIS CABINET.
INTERIOR CABINETS AND SQUAD BENCH, CURB SIDE
1 1 SQUAD BENCH STORAGE:
Storage shall be provided under the bench cushions. The area shall
be approximately 6" deep and shall run where possible under the
bench. The storage pan shall be fabricated from aluminum and shall
be accessed by raising the split cushions.
1 1 SQUAD BENCH END RESTRAINT FOR USE WITH HOPS
Install a restraint that is 16" above the seating surface at the
head end of the bench. Standard for use in conjunction with HOPPS 3-
point seat belts.
812712012 DWG #1050 78
! ! ! NOTE SHARPS WASTE DRAWER THAT OPENS INTO STEPWELL AT HEAD OF BENCH.
! ! ! CUSTOM HEIGHT BOLSTER. BOLSTER TO BE 43" HIGH ILOS.
IG10A000 1 1 BENCH HOLD OPENS: gas
Install gas spring hold opens on squad bench lid.
IG100000 1 1 BENCH HOLD-DOWN: paddle latches (Pair)
Install recessed paddle latches into the squad bench riser to retain
the squad bench lids in the closed position. The latches shall be
both passive and positive.
11747
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10: 09:24 PM Rev 2 Page 18 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE Selected Feature List
6000 HIATUS ROAD Year:
TAMARAC FL 33321 mHomon
STEVE STILL WELL NEMMQW=Y VEHICI M Chassis:
Model:
Option Std Oil Header/Description/Data Proposal Total
IG15A000 1 1 BENCH CUSHION EDGE TRIM:
Trim bench cushion edge with protective aluminum trim, to protect
horizontal edge of squad bench cushion from tears..
IG1513000 0 1 BENCH BACK CUSHION: full size
Delete individual squad bench back cushions. Install full size
cushion.
41212012
IK17E000 0 1 SHARPS/WASTE STORAGE IN A PULL OUT DRAWER IN SQUAD
BENCH
Install a drawer in the face of the squad bench in the specific
location noted below. This drawer will house both sharps and waste
containers.
111712013 ! ! ! THIS IS TO BE A CUSTOM ASSEMBLY THAT WILL RECESS THROUGH THE CRASH
RESTRAINT WALL AT THE HEAD OF THE BENCH AND EXTEND INTO THE INSIDE OF THE
BENCH PAN. BUILD TO HOLD (2) 8970 CONTAINERS. INCLUDE INSERTS TO
STABILIZE CONTAINERS. INSTALL RED LAMINATE COVERED ALUMINUM SLIDING DOORS
FOR ACCESS TO CONTAINERS AT HEAD OF BENCH. CONTAINERS TO BE INSTALLED IN A
PULL OUT DRAWER THAT OPENS INTO STEPWELL TO CHANGE CONTAINERS.
IK18AA00 1 1 CURBSIDE OVERHEAD CABINET: hinged doors
Storage shall be provided above the squad bench. The storage shall
run the full length of the squad bench and shall be accessed through
hinged Plexiglas doors that are held in the open position with gas
activated rods. The entire cabinet shall be fabricated from
aluminum. The cabinet is to be 911 H to meet current K requirements.
IK290000 0 1 GLOVE STORAGE CABINET AT FOOT OF BENCH
Fabricate a storage box on the wall over the foot of bench for
storage of (3) boxes of rubber gloves. Provide oval openings in a
hinged Plexiglas door for glove access.
811912013 Glove box size:
ISP00001 0 1 SPECIAL INSTRUCTION, CURBSIDE CABINETRY
111712013 ! ! ! INSTALL A CABINET IN THE UPPER PORTION OF THE CURBSIDE REAR
COMPARTMENT (over foot of bench) LOCATE ABOVE THE OPEN STORAGE AND INSTALL
A HINGED LAMINATE COVERED ALUMINUM DOOR. INSTALL FLUSH MOUNT LATCH AND A
NATIONAL KEY LOCK. CABINET TO BE MAXIMUM WIDTH AND HEIGHT AND EXTEND TO
THE VERTICAL DIVIDER IN COMPARTMENT. THIS IS TO HAVE SECURITY STYLE HINGES
INSTALLED AND WILL BE USED AS A DRUG CABINET.
11747
2014
Navistar 108"
623
Hall -Mark Fire. Thursday, November 07, 2013 Print Features
Michael Day 10: 09:24 PM Rev 2 Page 19 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE
6000 HIATUS ROAD
TAMARAC, FL 33321
STEVE STILL WELL
• &-V . 7 /1 . T T 7 /T • . •
- =Horton
MEME NIMICY VEHICLES
ISP00002 0 1 SPECIAL INSTRUCTION, CURBSIDE CABINETRY
Selected Feature List 11747
Year:
Chassis:
Model:
i Total
811912013 ! ! ! FABRICATE A DROP IN SHARPS JUST BELOW GLOVE STORAGE IN WALL AT FOOT OF
BENCH. EXACT DESIGN TBD AT PRE -BUILD.
INTERIOR CABINETS, FRONT
JAK03000 1 1 FRONT WALL CABINET:
The front wall cabinet shall be arranged per drawing. Additional
configuration information may follow.
1211012012 Cabinet wall finish: paint
r ► NOTE, MAX COOL AC UNIT AND DANHARD 110V AC UNIT ON TOP OF CABINET.
INSTALL ALL COMPONENTS ASSOCIATED WITH UNITS IN BOTTOM OF CABINET.
! ! ! MODIFY INBOARD SIDE OF CABINET FOR LINES AND WIRING.
JE040000 4 4 FRONT WALL DOORS: Plexiglas
Front cabinet wall to have hinged Plexiglas doors, and latch type as
designated.
111712013 Type:
Latch Style:
LEXAN
Southco
! ! ! DOORS TO BE LEXAN ILO PLEXIGLAS. DO NOT REMOVE PROTECTIVE COATING.
JSP00001 0 1 SPECIAL INSTRUCTION, FRONT WALL CABINET
112912013 ! ! ! INSTALL CUSTOMER SUPPLIED MEDVAULT KNOX BOX IN CROSSOVER CABINET
LOCATION.
! r ! KNOX BOX WILL BE FLUSH MOUNT STYLE.
K MODULE INTERIOR ACCESSORIES AND TRIM
KG02B000 2 4 IV HANGER, CAST PRODUCTS WITH RUBBER ARM
Cast products recessed IV hangers with rubber arms for attaching
solution bags shall be installed in the designated locations.
812112012 Locate: HEAD AND FOOT OF BENCH, AISLE EDGE
HEAD AND FOOT OF COT, STREETSIDE
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:25 PM Rev 2 Page 20 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE Selected Feature List
6000 HIATUS ROAD Year:
TAMARAC, FL 33321 mHomon STEVE STILL WELL MEMMOMOCY VEHICLM Chassis:
Model:
cnn 5td ntv Header/Descrintion/Data _Proposal Total
KG09B000 1 1
812112012
CEILING GRAB RAIL: standard (2) 2ft rails or (1) 6ft rail anti -microbial
Cabinet wall "A" will have (1) 6" rail over cot as standard.
Cabinet wall "B" will have (2) 21 rails, 1-forward and 1-to rear of
CPR seat.
KG0913000 0 1 GRAB RAIL: additional 6ft with anti -microbial coating
Additional (6)ft long ceiling mounted stainless steel grab rail with
anti -microbial coating.
812112012 Locate: AISLE EDGE OF BENCH
KG091000 0 1 VERTICAL GRAB RAIL INSTALLATION, 2 FT. ANTI -MICROBIAL
Install 2" stainless steel grab rail with anti -microbial coating.
812112012 Locate: STEPWELL SIDE OF HOPS BOLSTER
KG09K000 1 1 PATIENT DOOR GRAB RAILS: angled with anti -microbial coating
All patient access doors to have heavy duty angled stainless steel
grab rails with smooth radius corners and flange mounting and anti-
microbial coating.
KG110000 1 1 FLOOR TRIM
Trim floor with cove molding at non rolled areas of floor.
KG120000 1 1 CABINET TRIM
Trim all vertical and horizontal edges.
KG1613000 1 1 CEILING MATERIAL, PLATINUM WHITE ALUMINUM COMPOSITE
The standard module ceiling material shall be platinum white
aluminum composite.
KG17A000 2 2 FIRE EXTINGUISHERS: 51b ABC
Supply five pound fire ABC extinguisher(s). Ship loose, or identify
mounting location (s) .
Locate: SHIP LOOSE
11747
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:25 PM Rev 2 Page 21 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE Selected Feature List 11747
6000 HIATUS ROAD Year: 2014
TAMARAC, FL 33321 mHorton
STEVE STILL WELLMERGE OCY VEHICLES Chassis: Navistar 108"
Model: 623
Oytion Std Otv Header/Description/Data Proposal Total
L COT MOUNTS AND ACCESSORIES
LSP00001 0 1 SPECIAL INSTRUCTIONS, COT MOUNTS & PATIENT HANDLING
111712013 ! ! ! REINFORCE PATIENT COMPARTMENT FLOOR FOR INSTALLATION OF STRYKER POWER
LOAD COT SYSTEM.
! ! ! HORTON IS TO INSTALL A CUSTOMER SUPPLIED STRYKER POWER LOAD SYSTEM.
! ! ! LOCATE FOR CENTER POSITION ONLY.
M LIGHTBARS FRONT AND REAR
MAM148FO 1 1 FRONT LIGHTBARS FOR 96" BODIES
0 1 LIGHT BAR: custom front
maml 5y00 Install special front light bar.
111712013 Model: WHELEN 60 " FREEDOM BAR
Configure: SEE LAYOUT IN FILE.
0 1 LIGHT BAR MOUNT: cab roof
mam20a00 Mount light bar on cab roof.
41212012 Model: selected above
MIDI ELECTRICAL EMERGENCY VISUAL WARNING SYSTEMS
MM01 A000 0 1 WIGWAG HEADLIGHTS:
Install wig wag headlight flasher.
41212012
MM030000 1 1 WHELEN M SERIES LIGHTING OPTIONS:
Mall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:26 PM Rev 2 Page 22 of 38
TAMARAC FIRE RESCUE
6000 HIATUS ROAD
TAMARAC, FL 33321
STEVE STILL WELL
TR 12430- Exhibit A
Selected Feature List 11747
-I—Lorton
EEME WO CY VEHICLES
intion/Data _ _ Pro
MM10CL00 0 5 L.E.D. WARNING: compartment door (EACH)
Year:
Chassis:
Model:
1 Total
Install
custom made L.E.D.
light strips on
the interior
of the
exterior
compartment door
panels. The light
strips shall
have an
integral
lens strip for maximum
light disbursement.
Installation
will be
flush with the ALD
inner panel. The
light strip
shall flash
when the
compartment door
is open, and the
red flashing
light
circuit
is activated.
1212712012 Compartment: ALL REAR FACING COMPARTMENT DOORS, EXCEPT STREETSIDE
UPPER Color: RED
r r POWERED WITH BATTERY SWITCH, REGARDLESS OF WARNING MODE.
MM10L000 0 4 L.E.D. WARNING: patient entry door (EACH)
Install custom made L.E.D. light strips on the interior patient
entry door panels. The light strips shall have a integral lens strip
for maximum light disbursement. Installation will be flush with the
inner door panel. The light strip shall flash when the door is open,
and the red flashing light circuit is'activated.
1212712012 Color: RED
Location: (1) ON EACH REAR ENTRY DOOR, UPPER PORTION
(2) ON SIDE ENTRY DOOR, UPPER AND LOWER
! ! POWERED WITH BATTERY SWITCH, REGARDLESS OF WARNING MODE.
MM26BO30 0 8 RED SUPER L.E.D. LIGHT, 900 SERIES
Whelen 900 series red super L.E.D. lights shall be installed in the
designated locations.
1211012012 Location:
(2) FRONT FACE OF BODY
(2) STREETSIDE
(2) CURBSIDE
(2) REAR FACE OF BODY,
UPPER OUTBOARD CORNERS
MM26RO30 0 1 AMBER SUPER L.E.D. KKK REAR LIGHT, 700 SERIES
(1) AMBER series 700 super L.E.D. light to be mounted centered on
rear face of modular body.
51712012
MM26TI30 0 1 INTERSECTION LIGHTS, WHELEN SUPER L.E.D. 400 SERIES RED
WITH FLANGE
Intersection lights shall be Whelen 400 series super L.E.D. style.
41212012
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day
10:09:26 PM
Rev 2 Page 23 of 38
1
TR 12430- Exhibit A
TAMARAC FIRE RESCUE
6000 HIATUS ROAD
TAMIARAC, FL 33321
STEVE STILLWELL
• . •
-- -Horton
EMERGENCY VEHICLE$
Selected Feature List
Year:
Chassis:
Model:
Proposal Total
MM26UI30 0 1 GRILLE LIGHTS, WHELEN SUPER L.E.D. 700 SERIES RED
Grille lights will be Whelen super L.E.D. style.
11312013
MM26UI30 1 1 GRILLE LIGHTS, WHELEN SUPER L.E.D. 700 SERIES RED
Grille lights will be Whelen super L.E.D. style.
11312013
MMSP0010 0 1 SPECIAL INSTRUCTION, VISUAL EMERGENCY WARNING SYSTEMS
111712013 ! ! ! SUPPLY AND INSTALL A WHELEN 500 SERIES TIR 6 SUPER LED RED LIGHT WITH
CLEAR LENS ON EACH SIDE OF CAB BETWEEN FRONT AND REAR DOORS.
! r SUPPLY AND INSTALL A WHELEN TIR 6 RED LED WITH CLEAR LENS ON EACH SIDE
OF THE REAR DIAMOND PLATE RISER. LIGHTS TO BE PROGRAMMED FOR BRAKE
ACTIVATION IN ADDITION TO FLASHING IN EMERGENCY MODE.
! ! ! SUPPLY AND INSTALL A WHELEN 500 SERIES TIR 6 SUPER LED RED LIGHT WITH
CLEAR LENS ON EACH SIDE OF BODY ABOVE REAR WHEEL WELLS.
! ! ! TOTAL OF (6) .
MMSP0020 0 1 SPECIAL INSTRUCTION, VISUAL EMERGENCY WARNING SYSTEMS
111712013 ! ! ! SUPPLY AND INSTALL A WHELEN #OSROOMCR STEADY BURN LIGHT ON THE LOWER
INNER PANEL OF EACH CAB DOOR . AND ACTIVATE WITH THE CAB DOOR OPEN CIRCUIT.
INSTALL LIGHTS AS FAR OUTBOARD AS POSSIBLE.
TOTAL OF (4) .
MMSP0030 0 1 SPECIAL INSTRUCTION, VISUAL EMERGENCY WARNING SYSTEMS
1212712012 ! ! ! INSTALL CONSPICUITY LIGHTING DESIGN ON REAR OF MODULE. INSTALL (5) PER
BODY SIDE WITH LOCATION AT AN ANGLE.
TOP TO BOTTOM: R/A/R/A/R
MN09N000 1
! ! ! PROGRAM RED TO FLASH WITH BRAKE LIGHT CIRCUIT. PROGRAM AMBER TO FLASH
WITH TURN SIGNALS.
AUDIBLE EMERGENCY WARNING SYSTEMS
1 AIR HORN: medium duty chassis
The chassis shall have air horns installed from the chassis
manufacturer. The air horns shall use the chassis air system. The
air horns can only be activated when the vehicle is in gear.
511512012 Trumpet Locate: CHASSIS FENDERS
Activation: OEM
11747
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:26 PM Rev 2 Page 24 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE
6000 HIATUS ROAD
TAMARAC, FL 33321
STEVE STILLWELL
• . •
mHoMon
0 MEMENCY VEHICUS
Selected Feature List
Year:
Chassis:
Model:
Proposal Total
MN35EF10 0 1 SIREN, FEDERAL PA30OMSC
Specified siren to be: Federal PA300MSC, 200 watt w/microphone and
Hi-Lo tone.
1212712012 ! ! ! WIRE TO DRIVER SIDE SPEAKER.
! ! ! INSTALL IN DRIVER SIDE OF OEM OVERHEAD CONSOLE.
MN35EF20 0 1 SIREN, FEDERAL E02B
Specified siren to be: Federal EQ2B 200 watt electronic with digital
output control.
1212712012 ! ! ! WIRE TO PASSENGER SIDE SPEAKER.
!!! INSTALL IN DRIVER SIDE OF OEM OVERHEAD CONSOLE.
MN40A000 1 2 SIREN INSTALL:
The siren listed above shall be supplied and mounted as defined.
41212012
MN45UL00 1 1 SPEAKERS, SA3803
Install SA3803 siren speakers.
MN50A000 1 1 SPEAKER INSTALL: bumper
Speaker Selections (Bumper Installed)
OL09L000 0 1 KKK SIDE BODY MARKER LIGHTS, 700 SERIES L.E.D. (PAIR)
Install red Whelen L.E.D. 700 series turn/marker lights on each
rear side of the module body. Lights provide module body nighttime
side lighting visibility and turning signal indication.
41212012 ! ! ! PROGRAM HIGH INTENSITY PORTION OF LIGHT TO FLASH WITH WARNING LIGHTS.
11747
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:26 PM Rev 2 Page 25 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE Selected Feature List 11747
6000 HIATUS ROAD
Year: 2014
TAMARAC, FL 33321 =
STEVE STILLWELL
� ■Horton Chassis: Navistar 108"
Model: 623
�tlon Std Oty Header/Descrhytlon/Data Proposal Total
OL34L000 1 1 LED EXTERIOR COMPARTMENT LIGHTING
All exterior compartments will be lighted with LED strip lighting.
A vertical strip will be installed inside both sides of each
compartment. The lights shall be directed toward the back of the
compartment.
Note: This does not include wheelwell compartments.
OL350000 1 1 ICC MARKER LIGHTS
LED ICC marker lights shall be installed.
OL41 B000 0 1 RUNNING BOARD LIGHTS, WHELEN PAR 16 L.E.D.
Clear Whelen Par 16 round L.E.D. lights mounted in chrome flanges
shall be installed in the front of the module body . Locate in the
stainless steel stone guard above the running boards. The lights
shall be wired to the chassis door switch and illuminate the
step/running board.
41212012 REQUIRES PRE -PUNCHED STONE GUARDS DR030000 or DH03B000.
OM25AA00 0 4 SIDE SCENE LIGHTS, 900 SERIES, LED
Install Whelen 900 series #9SCOENZR side scene lights.
812112012 Locate: (2 ) PER SIDE, PER DRAWING
OM25DD00 0 2 LOAD LIGHTS WHELEN 900 SERIES LED
Rear load lights to be (2) Whelen #9SCOENZR LED lights.
41212012
OM301_700 0 1 TAIL LIGHTS, 600 SERIES L.E.D. WITH HALOGEN REVERSE
(1) set of Whelen 600 series L.E.D. lights shall be installed on the
rear of the vehicle as designated. They shall include L.E.D.
stop/tail and turn signals. The backup lights shall be halogen.
1212712012 Locate: REAR RISER, NOTE COMPARTMENT BELOW REAR DOORS
OSP00001 0 1 SPECIAL INSTRUCTION, ELECTRICAL
811912013 ! ! ! SUPPLY AND INSTALL A BLCK GO -LIGHT MODEL 2020 IN THE CENTER OF THE
CAB ROOF BEHIND THE LI GHTBAR . INSTALL ON A RAISED MOUNT SO LI GHTBAR DOES
NOT BLOCK. CONTROLS TO BE INSTALLED IN PASSENGER ' S SIDE OVERHEAD CUBBY ON
THE LEFT SIDE.
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:26 PM Rev 2 Page 26 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE
6000 HIATUS ROAD
TAMARAC, FL 33321
STEVE STILL WELL
. ..
=Horton
NEIiIERGENCY VEHICLE$
OSP00002 0 1 SPECIAL INSTRUCTION, ELECTRICAL
Selected Feature List 11747
Year:
Chassis:
Model:
Proposal Total
111712013 ! 1.1 SUPPLY AND INSTALL (3) WHELEN LED I CC LIGHTS ON HEADER PANEL OVER THE
REAR DOORS. INSTALL RED LIGHT IN CENTER WIRED TO THE CHASSIS BRAKE LIGHT
CIRCUIT. INSTALL AMBER ON EACH SIDE AND WIRE TO THE CHASSIS TURN SIGNAL
CIRCUITS.
OSP00003 0 1 SPECIAL INSTRUCTION, ELECTRICAL
111712013 ! ! ! SUPPLY AND INSTALL (2) WHELEN LED PIONEER PLUS SCENE LIGHTS MODEL
#PFP2.
INSTALL (1) CENTERED ON EACH BODY SIDE IN WHELEN PBA203 SEMIRECESSED
HOUSINGS WITH CHROME FLANGES. (2) TOTAL.
0
PAL00003
ELECTRICAL POWER GROUP
1 1 INTELLIPLEX MULTIPLEX ELECTRICAL SYSTEM:
Install the Intelliplex Multiplex electrical system.
PALOOA00 0 1 MODULE DISCONNECT DEFAULT
The module disconnect circuit shall default to the "on" position
when the battery switch is activated.
41212012
PAL01 BOO 1 1 BATTERY SWITCH: std. operation
The "Master" battery switch shall switch battery power "on" and
"off" to the ambulance body and conversion added electrical
circuits only. All OEM chassis electric's, (headlights, ignition,
keep alive) shall remain wired "hot" and have no ability to be
switched "off", and provide circuit function as provided by the
chassis manufacturer.
NOTE: DO NOT MODIFY OEM BATTERY SWITCH UNLESS STATED BELOW.
811912013 ! ! ! INSTALL A SMALL ANGLED BOX BETWEEN DRIVER SEAT AND DOOR. INSTALL
SWITCH IN BOX.
PAL04DOO 1 1 CHARGER/POWER SUPPLY: 45 AMP
Install a 45 amp battery conditioner in the designated electrical
equipment area. Conditioner to be wired to the batteries through the
standard shoreline inlet.
1211012012
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10: 09:26 PM Rev 2 Page 27 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE
6000 HIATUS ROAD
TAMARAC, FL 33321
STEVE STILL WELL
Selected Feature List 11747
— =Horton
IIIM OLME WOCY VEHICLES
ill tio1Z/d ata Pro
Year:
Chassis:
Model:
Total
PAL31 C00 3 7 INTERIOR 12VDC OUTLETS: cigarette lighter type
12 volt outlets to use cigarette lighter style connectors.
91712012 Locate: (2) INHALATION AREA PER DRAWING
Locate: (2) LOWER LINEN CABINET PER DRAWING
SURFACE MOUNTED
Locate: (2) PASSENGER SIDE OF CAB CONSOLE PER DRAWING
Locate: (1) IN FRONT WALL CABINET PER DRAWING
Configure:
BATTERY HOT
PAL38E00 0 2 SHORELINE, KUSSMAUL SUPER AUTO EJECT, 20 AMP NON ARCING
Install a 20 amp Kussmaul non -arcing auto ejection shoreline
receptacle.
811912013 Locate: FRONT FACE OF BODY, DRIVER SIDE TO DUPLICATE 14208.
! ! ! INSTALLED IN ANGLED HOUSING ANGLED AWAY FROM THE CAB.
! ! ! ONE TO BE DEDICATED TO DANHARD UNIT.
! ! ! COVERS TO BE RED.
PAL381LO 0 2 SHORELINE INDICATOR:
Install an indicator pilot light to show power to A.C. circuits and
presence of activated shoreline.
712712012 Locate: ABOVE THE SHORELINE INLET
Configure: LED
THIS TO BE WELDON GREEN LED ILOS
PAL40000 1 1 EXTRA 12VDC CIRCUIT BREAKER:
An extra circuit breaker shall be installed.
PL10A000 1 1 SWITCH PANEL MOUNT:
Switch panel to be flush mounted in upper face of console.
1211012012 ! ! ! INSTALL IN OEM CAB DASH.
PL11 A000 0 1 LIGHT PROGRAMMING: side rear scene
The side rear scene lights shall be wired to transmission reverse,
plus standard mode of operation.
41212012
2014
Navistar 108"
�-w
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:26 PM Rev 2 Page 28 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE
6000 HIATUS ROAD
TAMARAC, FL 33321
STEVE STILL WELL
Selected Feature List 11747
•Houton
EEMERGE#1 Y VEHICLES
iytion/Data Pro
Year:
Chassis:
Model:
Total
PL11 13000 0 1 LIGHT PROGRAMMING: right side scene
The right side scene lights shall come "on" when the side patient
door is opened.
41212012
PL11 C000 0 1 LIGHT PROGRAMMING: load light
The rear load lights shall be wired to transmission reverse, plus
the standard mode of operation.
41212012
PL11 F000 1 1 PROGRAMMING: AUDIBLE LOW VOLTAGE ALARM
Program an audible alarm to activate if the voltage drops below 11.8
volts for 120 seconds.
PL11 G000 1 1 LIGHT PROGRAMMING: park brake
A warning shall display on the front console readout, advising to
set the Parking Brake, should the modular disconnect switch be "ON"
and the transmission placed in "PARK" or "NEUTRAL". It will also
advise to Disengage the Parking Brake should the vehicle be placed
into gear.
Configure:
wire alarm to activate with red flasher circuit
PL190000 1 1 REPORT LIGHT:
A report light shall be located at the action wall to light the
counter area
111712013 ! ! ! SUPPLY AND INSTALL A 12. 6' TECNIQ LED BAR LIGHT ILOS REPORT LIGHT.
! ! ! LIGHT TO BE SWITCHED THROUGH THE REAR CONTROL PANEL.
PL220000 1 1 STEP WELL LIGHT:
Install one step well light for the right side patient door. Light
to come on when door is opened.
111712013 ! ! ! SUPPLY AND INSTALL A WHELEN PAR 16 LED LIGHT.
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:26 PM Rev 2 Page 29 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE Selected Feature List
6000 HIATUS ROAD Year:
TAMARAC, FL 33321 =HoMo l
STEVE STILLWELL 111110 1111MOMEMYVEMOUN Chassis:
Model:
ion Std Oty Header
/Descrivtion/Data Proposal Total
PL23A000 0 2 2.5" CAB CEILING LIGHTS, COMBINATION WHITE/RED LED
LED lights shall be installed in the cab headliner above the driver
and passenger seats. Each light contains a combination of white and
red LED's which will be switched separately in the front control
panel.
811912013 Manufacturer #E13-WSOR-1 lights with chrom trim ring #E13-WS001
Locate: ONE ABOVE EACH CAB SEAT. TOTAL OF 4
EACH LIGHT TO HAVE A SEPARATE CONTROL SWITCH.
PL24B000 0 3 FLUORESCENT LIGHTS:
Install 24 inch 12 volt fluorescent ceiling light fixtures. Wire to
charger/conditioner in addition to standard mode of operation.
111712013 Locate: FRONT, CENTER AND REAR OF PATIENT CEILING
r r i ILOS SUPPLY AND INSTALL ROM DUROLUMEN V3 LED INTERIOR LIGHT #R03215.
PL24T000 0 1 LAMP TIMER: programmable
Install an electronic momentary touch timer switch where specified.
The switch will enable time limited operation of the below listed
lights, with the battery switch in the off position.
11312013 Locate: STEPWELL SIDE OF HOPS BOLSTER
Light (s) Controlled: DUROLUMEN LIGHTS
SET ELAPSED TIME FOR 15 MINUTES
PL27CE00 0 7 PATIENT CEILING DOME LIGHT LENS: Concept Style
Concept 3 style LED dome lights will be installed in the designated
areas of the patient ceiling.
1211012012 Locate: PER OVERHEAD DRAWING
PL280000 1 1 GOOSENECK PANEL LIGHT
Install a flexible goose neck panel light in the following area.
41212012 Locate: PASSENGER SIDE OF CAB CONSOLE
THIS IS TO BE A FEDERAL SIGNAL LED LITTLE LIGHT.
PL29P000 0 3 PREWIRE FOR FUTURE STREAMLIGHT INSTALLATION
Prewire shall be provided as noted below for future installation of
Streamlight charger bases.
811912013 Quantity: 3
Locate: (1) STREETSIDE INTERMEDIATE, LEFT WALL CLOSE TO CENTER
(1) CURBSIDE FORWARD, FRONT WALL, TOP PORTION, BACK WALL
(1) CURBSIDE FORWARD, FRONT WALL, LOWER PORTION, BACK WALL
11747
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09.26 PM Rev 2 Page 30 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE Selected Feature List 11747
6000 HIATUS ROAD
Year: 2014
TAMARAC, FL 33321 mHoft0'l
STEVE STILLWELL .MEM�%IEMCLM Chassis: Navistar 108"
Model: 623
Option Std Otv Header/Descriytion/Data proposal Total
PM110000 0 1 LIGHT PROGRAMMING: brake light
Lower red flashing lights to operate as brake lights when not in the
warning mode.
41212012 Configure: flashers to override brake light feature
Note: feature to activate regardless of module disconnect
status
PSP00001 0 1 SPECIAL INSTRUCTION, ELECTRICAL POWER, PROGRAMMING
111712013 ! ! ! SUPPLY AND INSTALL 12V POWER AND GROUND STUD IN THE REAR MOST PATIENT
CEILING BAY. THIS IS TO BE WIRED BATTERY HOT AND WILL BE USED FOR FUTURE
INSTALL OF DVD SYSTEM.
PSP00002 0 1 SPECIAL INSTRUCTION, ELECTRICAL POWER, PROGRAMMING
111712013 ! ! ! SUPPLY AND INSTALL A KUSSMAUL #091-9 AUTO AIR PUMP. THIS IS TO BE
TIED INTO THE CHASSIS AIR SYSTEM AND INSTALLED IN THE UPPER STREETSIDE
FORWARD COMPARTMENT.
HEATING. AIR CONDITIONING AND INTERIOR ENVIRONMENT
OH291200 0 1 HEAVAC SYSTEM -COMPRESSOR & CONDENSOR, NAVISTAR, FACE
Install a ProAir 12V heat/AC system, complete with compressor and
condenser, for the Navistar 4300. Unit is to include 3-ply
replaceable carbon filters at the air intake point. This system
shall not tap into the chassis OEM heat/AC system. Includes a top
mounted condenser for DT466.
41212012 Note: Compressor to be ordered with the chassis.
OH29MX00 0 1 MAX COOL II DUAL A/C UNIT
Install a dual 12V air conditioning system as noted below. The
second A/C unit shall be a ProAir 938. This system shall include a.
second evaporator and a 3-fan condenser and shall be run off of the
auxiliary A/C compressor. This system shall include a separate
'High/Low' function at the second unit. This second unit shall
operate as A/C only. An accumulator is required for this
installation.
812112012 Locate: FRONT WALL CABINET PER DRAWING
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:26 PM Rev 2 Page 31 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE Selected Feature List
6000 HIATUS ROAD
Year:
TAMARAC, FL 33321 � =
� Horton
STEVE STILL WELL EMOM&CY VEHICLM Chassis:
Model:
ion Std Otv Header/Description/Data Proposal Total
OH29N000 0 1 PAINT AUXILIARY CONDENSER, FRONT FACE, TO MATCH BODY:
Paint the auxiliary condensor mounted on the front face of the body
to match the body color. Standard color is white.
41212012
OH310000 0 4 3-PLY PANEL INTAKE FILTER
Install a 3-Ply Panel air intake filter ILOS. (1) 16.75" x 8.75"
#10008973 for attendant seat base or above right front cabinet.
(2) 13" x 18" #10009296 over#1 compartment or in bottom of linen
cabinet. Filters will be behind stainless steel intake grills.
111412013 ! ! ! INSTALL ON ALL AC UNITS.
OL43C000 0 1 PERKO POWER VENT
Install a Perko power vent. Use existing ceiling plate and vent to
outside of modular body.
41212012
OL43D000 0 1 PERKO STATIC VENT
Install a Perko static vent. Use existing ceiling plate and vent to
outside of modular body.
41212012
OL455000 0 1 DANHARD 110V A/C SYSTEM
Install a Danhard 50-2000 110V heat/AC unit as noted below.
111412013 Locate: FRONT WALL CABINET PER DRAWING
Thermostat location: INHALATION AREA
! ! ! INSTALL ALL COMPONENTS BEHIND UNIT.
R CAB CONSOLE AND COMMUNICATIONS
RJ01 A000 1 1 ANTENNA COAX 1:
An RG 58U coax shall be installed so that the ambulance conversion
need not be disassembled.
1212712012 Exterior Termination: CAB ROOF
Interior Termination: LOWER LINEN CABINET
11747
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:26 PM Rev 2 Page 32 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE Selected Feature List 11747
6000 HIATUS ROAD Year: 2014
TAMARAC, FL 33321 •Houton
STEVE STILL WELL EMY YENS Chassis: Navistar 108"
Model: 623
Option Std ON HeaderlDescriotion/Data Proposal Total
RJ01 B000 0 1 ANTENNA COAX 2:
Install additional antenna coax and accesses.
1212712012 Exterior Termination: CAB ROOF
Interior Termination: LOWER LINEN CABINET
RJ01 C000 0 1 ANTENNA COAX 3:
Install additional antenna coax and accesses.
1211012012 Exterior Termination: CAB ROOF
Interior Termination: LOWER LINEN CABINET
RJ031MN00 0 3 ANTENNA: NMO type mount.
Supply and install NMO type antenna base as designated.
This option is less the antenna coax. An antenna coax option must be
selected to be installed.
812112012 Coax Number: ALL
RJ040000 1 1 RADIO CABLE PULL WIRE
A standard pull wire for radio installation shall be installed from
behind the driver's seat to behind the inhalation panel. Wire is to
run in a 3" conduit.
RJ050000 0 2 RADIO HEAD PANEL: blank
Blank removable panels shall be installed for future installation of
radio heads.
41212012 Locate: FRONT CONSOLE
INHALATION PANEL
RJ05B000 1 1 FRONT CONSOLE:
A console shall be fabricated to coordinate with the interior cab
color. Room shall be provided on the face of the console for
installation of radio and siren controls.
811912013 ! ! ! REINFORCE PASSENGER SIDE OF CAB CONSOLE FOR FUTURE INSTALLATION OF
LAP TOP .
RJ05C000 0 1 CONSOLE EXTENSION:
A box for mounting radio heads and storage maps, books, or binders
will be attached to the standard engine cover console. Standard box
includes (3) 2.5 storage sections, and 8.5 faceplate for radio
mounting.
811912013 r r r INSTALL (2) CUP HOLDERS IN THE REAR PORTION OF THE CAB CONSOLE.
! ! ! INSTALL (5) MAP SLOTS ANGLED UPWARD TOWARDS REAR. SEE DRAWING.
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10: 09:26 PM Rev 2 Page 33 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE
6000 HIATUS ROAD
TAMARAC, FL 33321
STEVE STILLWELL
• i •
— nF-ic rton
EEMERGEN" VEHICLES
RJ070000 0 2 RADIO CABLE INSTALL: customer supplied
Selected Feature List
Year:
Chassis:
Model:
Proposal Total
Customer supplied radio cables will be installed during the vehicle
construction. Cables to be tagged and marked at each end to identify
their installed location. All cables shipped to Horton must have the
vehicle production number clearly marked on the shipping package,
and delivered prior to or at time of modular pre -wire.
112912013 Locate: LOWER LINEN TO
LOWER LINEN TO
RJ08A000 0 3 RADIO POWER/GROUND:
RSP00001
T
TN020000
INHALATION
CONSOLE
Install three 6 gauge cables to positive and ground studs for radio
power. Wire one constant hot, one ignition hot and one ground.
41212012 Locate: INHALATION AREA, CAB CONSOLE, LOWER LINEN
Configure: battery switched, battery hot and ground
0 1 SPECIAL INSTRUCTION, CAB CONSOLE & COMMUNICATIONS
112912013 ! ! ! HORTON TO SUPPLY AND INSTALL A 6 POSITION WIRELESS FIRECOM SYSTEM PER
BELOW AND QUOTE ON 'V' DRIVE IN PURCHASING FOLDER.
1 106-1310-10 301OR INTERCOM SINGLE RADIO
1 MR52X CABLE
3 UHW-51 WIRELESS HEADSET UNDER HELMET
RADIO TRANSMIT US/CAN
3 106-3089-00 WIRELESS BASE, SINGLE CHANNEL
2 UHW-54 WIRELESS HEADSET UNDER HELMET
ON/OFF INTERCOM US/CAN
1 106-3086-00 WIRELESS BASE, 5-CHANNEL
5 520-0676-00 HANGER HOOK FOR HEADSET
ROHS - BLACK
DRIVER AND PASSENGER CAB ROOF
REAR CREW AREA, CENTERED OVERHEAD
ACTION AREA
HEAD OF BENCH WALL
EACH LOCATION SHALL HAVE POWER FOR CHARGING
OXYGEN AND SUCTION
0 1 OXYGEN ACCESS:
4/2/2012
OF THE HEADSET.
A clear Plexiglas door shall be provided in the patient area wall
for access to the oxygen cylinder valve. The door shall be hinged
so that it swings into the oxygen cylinder storage compartment. The
opening shall be trimmed with anodized aluminum edging. O.D.
dimension of the access is 71/ wide x 11" high.
11747
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:27 PM Rev 2 Page 34 of 38
TAMARAC FIRE RESCUE
6000 HIATUS ROAD
TAMARAC, FL 33321
STEVE STILL WELL
TN030000 2
TR 12430- Exhibit A
Selected Feature List 11747
• . •
2 OXYGEN OUTLETS, STANDARD
•� =Horton
MEMMWMWY YEHICUM
Pro
Year:
Chassis:
Model:
Total
Two oxygen outlets shall be provided as standard and shall be
located in the inhalation panel.
TN03A000 0 2 OXYGEN OUTLET: additional
Install additional oxygen outlet(s).
812112012 Locate: CEILING OVER HEAD OF COT
WALL AT HEAD OF BENCH
TN04A000
TNO50000
TN060000
TN100000
TN 11 B000
X
0 1 ADAPTER TYPE: Ohio Diamond II
Oxygen outlets to be Ohio Diamond II.
412/2012
1 1 FLOWMETER:
Supply dial type flowmeter.
1 1 OXYGEN WRENCH:
Install oxygen wrench in oxygen compartment. Mount secure so not
left hanging. Mount with length of chain or cable so not removable.
1 1 VACUUM OUTLET: inhalation wall
A single vacuum panel shall be installed in the inhalation area.
The outlet shall be of the same style as the oxygen system and
hooked to the onboard vacuum pump.
0 1 ASPIRATOR: SSCOR
41212012
Install an SSCOR aspirator. The system shall include a #107CDC20
pump, #22000 wall mounted regulator, and a #23002 canister holder.
LETTERING
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:27 PM Rev 2 Page 35 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE
6000 HIATUS ROAD
TAMARAC, FL 33321
STEVE STILL WELL
UP010000 0 1 LETTERING:
Lettering to be included.
=Hor ton
EMERMMY VEHICLES
Selected Feature List 11747
Year:
Chassis. -
Model:
I Total
112912013 ! ! ! RED SCOTCHLITE WITH BLACK SCOTCHLITE BORDER ON BODY SIDES
WHITE SCOTCHLITE WITH BLACK SCOTCHLITE BORDER ON REAR ABOVE REAR
DOORS INSTALLED OVER RED DIAMOND GRADE MATERIAL.
1/1
SEE DEALER SUPPLIED LAYOUT IN ELECTRONIC FILE.
! ! ! ALL LETTERING IS SIZE TO FIT AT HORTON'S DISCRETION.
UP01 CD00 0 1 LETTERING REQUIRED.ON CAB DOORS
Lettering shall be installed on the cab doors. This lettering shall
meet the requirements listed below.
112912013 ! ! ! INSTALL CUSTOMERS SUPPLIED LOGOS ON CAB DOORS.
UP01 CS00 0 1 LETTERING REQUIRED ON CURBSIDE OF BODY
Lettering shall be installed on the curbside of the body. This
lettering shall meet the requirements listed below.
112912013 Configure: 'TAMARAC' SIZED TO FIT
'FIRE RESCUE' CUT OUT OF THE RED SCOTCHLITE BELTLINE STRIPE
UP01R000 0 1 LETTERING REQUIRED ON REAR OF VEHICLE
Lettering shall be installed on the rear of the vehicle. This
lettering shall meet the requirements listed below.
112912013 Configure: 'TAMARAC '
'FIRE & RESCUE'
UP01 SS00 0 1 LETTERING REQUIRED ON STREET SIDE OF BODY
Lettering shall be installed on the street side of the body. This
lettering shall meet the requirements listed below.
112912013 Configure: ' TAMARAC ' SIZED TO FIT
'FIRE RESCUE' CUT OUT OF THE RED SCOTCHLITE BELTLINE STRIPE
UP03C000 0 60 6" SHADED SCOTCHLITE LETTERING
112912013
UP08B000 0 2 STAR OF LIFE 12: (each)
Install 12" star of life.
112912013 Locate: ON REAR WINDOWS
! ! ! TO BE 'ETCHED STYLE ' ILOS .
2014
Navistar 108"
623
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:27 PM Rev 2 Page 36 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE Selected Feature List 11747
6000 HIATUS ROAD Year, 2014
TAMARAC, FL 33321 =F oMon
STEVE STILL WELL EEMERGENCY VEHIC!s Chassis: Navistar 108"
Model: 623
ion SO Otv Header/Description/Data Proposal Total
UP180000 1 1 DOOR REFLECTORS
Install 2" x 1211 strips of red Scotchlite at the top of each entry
door placed horizontally.
USP00001 0 1 SPECIAL INSTRUCTION, LETTERING
111712013 ! ! ! HALL -MARK TO SUPPLY AND INSTALL SIGN PLACARDS ON EACH TRUCK. COPY LAST
LAYOUT.
Y00 0 1 PRICE ADJUSTMENT: discount
Price discount, and or consideration.
811912013 Multiple Vehicle: $-1500
Z02 0 1 Factory Pickup and Transportation
Allowance for vehicle pickup, transportation and drivers fee.
811912013 F . 0. B . TAMARAC, FL
Z03 0 1 Dealer Prep. and Dealer Delivery
Allowance for vehicle preparation and delivery.
811912013
Z04 0 1 Fuel, Tags, Etc.
Allowance for fuel, tags and administrative.
811912013 UNIT TO BE DELIVERED WITH FLORIDA TAGS.
Z06 0 1 STATE CONTRACT:
This vehicle is subject to state contract pricing.
811912013 FLORIDA SHERIFFS ASSOCIATION CONTRACT 111-10-1202 1/2* FEE
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:27 PM Rev 2 Page 37 of 38
TR 12430- Exhibit A
TAMARAC FIRE RESCUE
6000 HIATUS ROAD
TAMARAC, FL 33321
STEVE STILL WELL
=Horton
■MWWWWV WHO=
Selected Feature List 11747
Year:
Chassis:
Model:
Proposal Total
2014
Navistar 108"
623
Total Configured Cost $273,45e.00
Authorized Department Signature(s):
Hall -Mark Fire Thursday, November 07, 2013 Print Features
Michael Day 10:09:27 PM Rev 2 Page 38 of 38
TR 12430- Exhibit Al
w
w
o � �
� $ CD
D n
o D
F1,11
i i I II II r�
X L J II II ��
N I I X
X r I �� i
� I
I I I � I I "t'I X
0N I II �o
X I i i 1 I I \� I I \� m
=o I L J I
10
Xc ►---- --- —�
0 a0 •
C/) cn c �` X
v
N V
\ a � X
r CD
VD r 0
v m Cl)
m v
rn r-
I � m a Z
CD v U)
m Cl) 0)
v N
m ZW
ICI]r—
ai � I D
` v a EM �` C
- m z I I r (n n
----cnI D av
r Z 1T1
0
rn * a 0m rn
X� I I ., I I z N_ —I
C/)Xa II t -nX o �
M I I M 1 i �D
CO -p I a � m rn _ r0
v�, \� II co�v (n rl
a I I Q "' oRP Ll
00
I
rn
I III oo r O
I II n II �
I q�bIII < o
rn
Z O O :%4
m-ic=0 c�a .a Cn
o I =0 n
r X2
I 1�vl
m
rL
om Xm
z X�Ko in
; o
— -- --- =z
CA)= X
v
m 0
�v rn
1 = z ,° n
D Z v
rnrn
z O m
` z446 rr: �
c
r
_
r� J
I J v
1
J
J
w
No Text
TR 12430- Exhibit Al
_CD
n o
2
r
v
cn
m n
c
m
M
0
U)
� o
m N
r No 0
I�IIllllu�ll
r
m -,
w IIIIY -,n o OjD
IIII� M z -o
m m — — — o �
Z o CID
> N
m N C w
m o ,D, ® U) —I
Z i
M m
0 70 0
nzC/)
F7 F7 o v > �C
--0( C
-ri � r
M � �r
IF rn
0
N N O O
rz co pD
-iz Im r-p
Cyr >c� �v 1
T o`=/ Z J
.L ^ Z O
v*
x
z�
Wox
0m
a 7D
m
446ra
o
' a
N —1
.a 111
\--�Im
II \\rn
II
IIZ
II \
,II
Z
M"
M"
TR 12430- Exhibit Al
T1
0
z
� N
o C
c�
02
-4M
viz
Un v
v
z
0
U)
7l
m
m
0
c
m
TR 12430- Exhibit Al
c
1 o
m r-
-o
CD
m o� cn
z zz
--1 X
m 3 ro -z
m X rn
O 0 c
o A _
0
cn
Z
-o D�III
v�alll r �
r
� O O
o �
�� �� Z �
m w
z m C -u
0 °
U) r > �]
:1) m
_ ODn
gcn(r000
®X = rn
m
-v
O o r—
i r Fn r
C
z
V
O
O
O
I
J
j 0
j
1
r
m
m
0
r
r
z
m
m
O
-v
L — I —
�r
_O
Dz
>O
mm
00
8
cn
O
m
A
z
TR 12430- Exhibit Al
0
nv
_a
-Z-i i
as
Am
m0
M
® X
® X
�N"//
w
m
n
74
L
U
\\1
a
n
z
a
A
m
cc/)
m
O
gz
D
MM
O�
�o
X
j
X
m
0
0
A
0
1l
m
m
C/)
C::
m
TR 12430- Exhibit B
NTERNAT ONAV October 31, 2013
Prepared For: Presented By:
HALL -MARK FIRE APPARATUS; TAMARAC FIRE MAUDLIN INT'L. TRUCKS, I
MICHAEL DAY Sally Wilson
3431 NW 27TH AVE 5221 WEST HIGHWAY 40
OCALA, FL 34475- OCALA FL 34482 -
(352)629 - 6305 (352)732-8151
Reference ID. 4300 LP - 4DR
Model Profile
2014 4300 SBA LP 4X2'(MH025)
APPLICATION:
Rescue
MISSION:
Requested GVWR: 25999. Calc. GVWR: 25999
Calc. Start / Grade Ability: 35.10% / 2.00%@ 55 MPH
Calc. Geared Speed: 85.0 MPH
FUEL ECONOMY.:
9.06 MPG @ 55 MPH
DIMENSION:
Wheelbase: 236.00, CA: 125.00, Axle to Frame: 96.00
ENGINE, DIESEL:
(MaxxForce DT) EPA 10, 260 HP @ 2200 RPM, 660 lb-ft Torque @ 1300 RPM9_2400 RPM
Governed Speed
TRANSMISSION, AUTOMATIC:
{Allison 3000EVS_P} 5th Generation Controls; Close Ratio, 6-Speed; With Double Overdrive,
Includes Oil Level Sensor, With Provision for PTO, Less Retarder, With 80,000-lb GVW & GCW
Max.
CLUTCH:
Omit Item (Clutch &'-Control)
AXLE, FRONT NON -DRIVING:
{Meritor MFS-10-143A} Wide Track, I -Beam Type, 10,000-Ib Capacity
AXLE, REAR, SINGLE:
{Dana Spicer 17060S} Single Reduction, 17,500-lb Capacity, 190 Wheel Ends Gear Ratio: 4.88
CAB:
Conventional 6-Man Crew Cab
TIRE, FRONT:
(2) 265/75R22.5 G661 HSA (GOODYEAR) 539 rev/mile, load range G, 14 ply
TIRE, REAR:
(4) 265/75R22.5 G622 RSD (GOODYEAR) 534 rev/mile, load range G, 14 ply
SUSPENSION, REAR, AIR, SINGLE:
(International} Ride Optimized Suspension (IROS); 18,500-lb Capacity, 5.3" Ride Height, With
Shock' Absorbers
PAINT:
Cab schematic 100GA
Location 1: 2562, Red (Prem)
Chassis schematic N/A
1 Proposal: 11235-01
INTERNATIONAL"
TR 12430- Exhibit B
Vehicle Specifications
2014 4300 SBA LP 4X2 (MH025)
October 31, 2013
Code Description F/R Wt Tot Wt
(Ibs) (Ibs)
MH02500 Base Chassis, Model 4300 SBA LP 4X2 with 236.00 Wheelbase, 125.00 CA, and 6351/2492 8843
96.00 Axle to Frame.
1570 TOW HOOK, FRONT (2) Frame Mounted 8/0 8
1 CAA FRAME RAILS High Strength Low Alloy Steel (80,000 PSI Yield); 9.125" x 3.062" 71/373 444
x 0.312" (231.8mm x 77.8mm x 8.Omm) With Transition to 6.500" x 3.062" x
0.312" (165.1 mm x 77.8mm x 8.Omm) 388.4" (9864mm) Maximum OAL; For LP
Chassis
Notes
: 6.50" Web Height in AF Section
1 LEG LICENSE PLATE HOLDER Includes Upper & Lower Mounting Plate Hardware, 3/0 3
Mounted in Existing Holes in Front Bumper
1 LNN BUMPER, FRONT Full Width, Aerodynamic, Chrome Plated Steel; 0.142" Material 0/0 0
Thickness
1 SAL
CROSSMEMBER, REAR, AF (01)
0/20
20
1 WEJ
WHEELBASE RANGE 199" (505cm) Through and Including 254" (645cm)
0/0
0
2ARX AXLE, FRONT NON -DRIVING {Meritor MFS-10-143A} Wide Track, I -Beam Type, 41/0 41
10,000-lb Capacity
Notes
: The following features should be considered when calculating Front GAWR: Front
Axles; Front Suspension; Brake System; Brakes, Front Air Cam; Wheels; Tires.
3ADB SUSPENSION, FRONT, SPRING Parabolic, Taper Leaf; 10,000-lb Capacity; With 65/0 65
Shock Absorbers
Includes
: SPRING PINS Rubber Bushings, Maintenance -Free
Notes
: The following features should be considered when calculating Front GAWR: Front
Axles; Front Suspension; Brake System; Brakes, Front Air Cam; Wheels; Tires.
4091 BRAKE SYSTEM, AIR Dual System for Straight Truck Applications 104/26 130
Includes
: BRAKE LINES Color and Size Coded Nylon
: DRAIN VALVE Twist -Type
: GAUGE, AIR PRESSURE (2) Air 1 and Air 2 Gauges; Located in Instrument
Cluster
: PARKING BRAKE CONTROL Yellow Knob, Located on Instrument Panel
: PARKING BRAKE VALVE For Truck
: QUICK RELEASE VALVE Bendix On Rear Axle for Spring Brake Release: 1 for
4x2, 2 for 6x4
: SLACK ADJUSTERS, FRONT Automatic
: SLACK ADJUSTERS, REAR Automatic
: SPRING BRAKE MODULATOR VALVE R-7 for 4x2, SR-7 with relay valve for 6x4
Notes
: Front and Rear Dust Shields not Included
4AZA AIR BRAKE ABS {Bendix AntiLock Brake System} Full Vehicle Wheel Control 9/21 30
System (4-Channel)
4EBT AIR DRYER {Bendix AD-IP} With Heater 0/0 0
2 Proposal: 11235-01
1 NTERNATIONAL®
TR 12430- Exhibit B
Vehicle Specifications
2014 4300 SBA LP 4X2 (MH025)
October 31, 2013
Code Description FIR Wt Tot Wt
(Ibs) (Ibs)
Includes
: AIR DRYER LOCATION Inside Left Rail, Back of Cab
4ESX
BRAKE
CHAMBERS,
FRONT AXLE {Haldex} 20 Sgln
0/0
0
4EVL
BRAKE
CHAMBERS,
REAR AXLE {Haldex GC3030LHDHO) 30/30 Spring Brake
0/6
6
Innh irfipq
: BRAKE CHAMBERS, SPRING (2) Rear Parking; WITH TRUCK BRAKES: All 4x2,
4x4; WITH TRACTOR BRAKES: All 4x2, 4x4; 6x4 & 6x6 with Rear Tandem Axles
Less Than 46,000-lb. or GVWR Less Than 54,000-lb.
4JCG BRAKES, FRONT, AIR CAM S-Cam; 15.0" x 4.0"; Includes 20 Sq. In. Long Stroke 83/0 83
Brake Chambers
Notes
: Front Axle with 14,000-lb GAWR is Limited to 13,200-lb GAWR when used in
Conjunction with 15" BRAKES, FRONT, AIR CAM.
: The following features should be considered when calculating Front GAWR: Front
Axles; Front Suspension; Brake System; Brakes, Front Air Cam; Wheels; Tires.
4NDB BRAKES, REAR, AIR CAM S-Cam; 16.5" x 7.0"; Includes 30/30 Sq.ln. Long Stroke 0/211 211
Brake Chamber and Spring Actuated Parking Brake
Notes
: The following features should be considered when calculating Front GAWR: Front
Axles; Front Suspension; Brake System; Brakes, Front Air Cam; Wheels; Tires.
4SBC
AIR COMPRESSOR
{Bendix Tu-Flo 550}
13.2 CFM Capacity
46/-1
45
5710
STEERING COLUMN Tilting and Telescoping
10/0
10
5CAL
STEERING WHEEL 2-Spoke, 18" Diam., Black
0/0
0
5PSM
STEERING GEAR {Sheppard HD941 Power
26/1
27
713HU
EXHAUST SYSTEM Single, Horizontal, Aftertreatment Device Frame Mounted
56/48
104
Right Side Back of Cab; Includes Vertical Tail Pipe & Guard
Includes
: EXHAUST HEIGHT 10' Exhaust Height - Based on Empty Chassis with Standard
Components (+ or - 1" Height)
: MUFFLER/TAIL PIPE GUARD Non -Bright Finish
7SCZ
ENGINE EXHAUST BRAKE for MaxxForce 16 Engines, Electronically Activated
0/0
0
7WBA
TAIL PIPE (1) Turnback Type, Bright, for Single Exhaust
0/0
0
7WBS
MUFFLER/TAIL PIPE GUARD (1) Bright Stainless Steel
0/0
0
7WZX SWITCH, FOR EXHAUST 3 Position, Momentary, Lighted Momentary, ON/ 2/0 2
CANCEL, Center Stable, INHIBIT REGEN, Mounted in IP Inhibits Diesel Particulate
Filter Regeneration When Switch is Moved to ON While Engine is Running, Resets
When Ignition is Turned OFF
8000 ELECTRICAL SYSTEM 12-Volt, Standard Equipment 0/0 0
Includes
: BATTERY BOX Steel
: DATA LINK CONNECTOR For Vehicle Programming and Diagnostics In Cab
: FUSES, ELECTRICAL SAE Blade -Type
: HAZARD SWITCH Push On/Push Off, Located on Top of Steering Column Cover
: HEADLIGHT DIMMER SWITCH Integral with Turn Signal Lever
: HORN, ELECTRIC Single
3 Proposal: 11235-01
INTERNATIONAL
TR 12430- Exhibit B
Vehicle Specifications
2014 4300 SBA LP 4X2 (MH025)
October 31, 2013
Code Description FIR Wt Tot Wt
(Ibs) (Ibs)
: JUMP START STUD Located on Positive Terminal of Outermost Battery
: PARKING LIGHT Integral with Front Turn Signal and Rear Tail Light
: STARTER SWITCH Electric, Key Operated
: STOP, TURN, TAIL & B/U LIGHTS Dual, Rear, Combination with Reflector
: TURN SIGNAL SWITCH Self -Cancelling for Trucks, Manual Cancelling for
Tractors, with Lane Change Feature
: TURN SIGNALS, FRONT Includes Reflectors and Auxiliary Side Turn Signals,
Solid State Flashers; Flush Mounted
: WINDSHIELD WIPER SWITCH 2-Speed with Wash and Intermittent Feature (5
Pre -Set Delays), Integral with Turn Signal Lever
: WINDSHIELD WIPERS Single Motor, Electric, Cowl Mounted
: WIRING, CHASSIS Color Coded and Continuously Numbered
8518
CIGAR LIGHTER Includes Ash Cup
1/0
1
8540
HORN, ELECTRIC (2)
2/0
2
8718
POWER SOURCE Cigar Type Receptacle without Plug and Cord
1/0
1
8GWY ALTERNATOR {Leece-Neville 14931 PAH} Brush Type, 12 Volt 320 Amp. 13/0 13
Capacity, Pad Mount
8HAB BODY BUILDER WIRING Back of Standard Cab at Left Frame or Under Extended 2/0 2
or Crew Cab at Left Frame; Includes Sealed Connectors for Tail/Amber Turn/
Marker/ Backup/Accessory Power/Ground and Sealed Connector for Stop/Turn
8MKX BATTERY SYSTEM {International} Maintenance -Free (3) 12-Volt 2775CCA Total 48/10 58
8RME RADIO AM/FM/WB/Clock/3MM Auxiliary Input, with Multiple Speakers, With CD 1/0 1
Player
8THB
BACK-UP ALARM Electric, 102 dBA
0/3
3
8TPA
DATA RECORDER Includes Display Mounted in Overhead Console
2/0
2
8WBW
JUMP START STUD Remote Mounted
2/0
2
Includes
: JUMP START STUD Mounted to Battery Box
8WCS BATTERY DISCONNECT SWITCH {Joseph Pollak 51-315} Positive Type, Lever 1/0 1
Operated, Cab Mounted
8WGL WINDSHIELD WIPER SPD CONTROL Force Wipers to Slowest Intermittent Speed 0/0 0
When Park Brake Set and Wipers Left on for a Predetermined Time
8WHE HORN, AIR ACCOMMODATION PACKAGE; less Horn 2/0 2
8WMA SWITCH, TOGGLE, FOR WORK LIGHT Lighted; on Instrument Panel and Wiring 2/1 3
Effects for Customer Furnished Back of Cab Light
8WPH CLEARANCE/MARKER LIGHTS (5) {Truck Lite} Amber LED Lights, Flush 0/0 0
Mounted on Cab or Sunshade
8WPZ TEST EXTERIOR LIGHTS Pre -Trip Inspection will Cycle all Exterior Lamps Except 0/0 0
Back-up Lights
8WRB HEADLIGHTS ON W/WIPERS Headlights Will Automatically Turn on if Windshield 0/0 0
Wipers are turned on
8WTL STARTING MOTOR {Delco Remy 39MT} 12 Volt; Gear Reduced, With Thermal 6/2 8
Over -Crank Protection
8WWJ INDICATOR, LOW COOLANT LEVEL With Audible Alarm 0/0 0
4 Proposal: 11235-01
INTERNATIONAL®
TR 12430- Exhibit B
Vehicle Specifications
2014 4300 SBA LP 4X2 (MH025)
October 31, 2013
Code
Description
FIR Wt Tot Wt
(Ibs) (Ibs)
8WXB
HEADLIGHT WARNING BUZZER Sounds When Head Light Switch is on and
0/0 0
Ignition Switch is in "Off' Position
8WZK
HEADLIGHTS Halogen; Composite Aero Design for Two Light System
0/0 0
8XAH
CIRCUIT BREAKERS Manual -Reset (Main Panel) SAE Type III With Trip
0/0 0
Indicators, Replaces All Fuses Except For 5-Amp Fuses
9HBM
GRILLE Stationary, Chrome
5/0 5
SWAY
FRONT END Tilting, Fiberglass, With Three Piece Construction
0/0 0
10060
PAINT SCHEMATIC, PT-1 Single Color, Design 100
0/0 0
Includes
: PAINT SCHEMATIC ID LETTERS "GA"
10761
PAINT TYPE Base Coat/Clear Coat, 1-2 Tone
0/0 0
10769
PAINT CLASS Premium Color
0/0 0
10WGD
SPECIAL RATING, GVWR Limited to 25,999-lb GVWR
0/0 0
11001
CLUTCH Omit Item (Clutch & Control)
-67/-8 -75
12NUP
ENGINE, DIESEL {MaxxForce DT) EPA 10, 260 HP @ 2200 RPM, 660 lb-ft Torque
52/2 54
@ 1300 RPM, 2400 RPM Governed Speed
Includes
: AIR COMPRESSOR AIR SUPPLY LINE Naturally -Aspirated (Air Brake Chassis
Only)
: ANTI -FREEZE Red Shell Rotella Extended Life Coolant; -40 Degrees F/ -40
Degrees C; for MaxxForce Engines
: COLD STARTING EQUIPMENT Intake Manifold Electric Grid Heater with Engine
ECM Control
: CRUISE CONTROL Electronic; Controls Integral to Steering Wheel
: ENGINE OIL DRAIN PLUG Magnetic
: ENGINE SHUTDOWN Electric, Key Operated
: FUEL FILTER Included with Fuel/Water Separator
: FUEL/WATER SEPARATOR Fuel/Water Separator and Fuel Filter in a Single
Assembly; With Water -in -Fuel Sensor; Engine Mounted
: GOVERNOR Electronic
: OIL FILTER, ENGINE Spin -On Type
: WET TYPE CYLINDER SLEEVES
Notes
: Recommend Code 12THT when using front mount obstructions (winches, cones,
reels, etc.) that restrict air flow through the radiator.
12THT
FAN DRIVE {Horton Drivemaster) Direct Drive Type, Two Speed With Residual
25/0 25
Torque Device for Disengaged Fan Speed
Includes
FAN Nylon
Notes
: Recommend Code 12THT when using front mount obstructions (winches, cones,
reels, etc.) that restrict air flow through the radiator.
12UBK
RADIATOR Aluminum; 2-Row, Cross Flow, Over Under System, 1045 Sqln
207/-18 189
Louvered, With 302 Sqln CAC, With 369 Sqln LTR, Includes In -Tank Transmission
Oil Cooler
5 Proposal: 11235-01
INTERNATIONAL&
TR 12430- Exhibit B
Vehicle Specifications
2014 4300 SBA LP 4X2 (MH025)
October 31, 2013
Code Description F/R Wt Tot Wt
(lbs) (lbs)
Includes
: DEAERATION SYSTEM with Surge Tank
: HOSE CLAMPS, RADIATOR HOSES Gates Shrink Band Type; Thermoplastic
Coolant Hose Clamps
: RADIATOR HOSES Premium, Rubber
12UXG
FEDERAL EMISSIONS for 2010; MaxxForce DT Engines
0/0
0
12VBR
AIR CLEANER With Service Protection Element
0/0
0
Includes
: GAUGE, AIR CLEANER RESTRICTION Air Cleaner Mounted
12VXT THROTTLE, HAND CONTROL Engine Speed Control; Electronic, Stationary, 0/0 0
Variable Speed; Mounted on Steering Wheel
12VZA ENGINE CONTROL, REMOTE MOUNTED Provision for; Includes Wiring for Body 0/0 0
Builder Installation of PTO Controls; With Ignition Switch Control for MaxxForce
post 2007 Emissions Electronic Engines
12WTA FAN DRIVE SPECIAL EFFECTS Fan Cooling Ring with Fan Shroud Effects, 14/-1 13
Engine Mounted
12WZE EMISSION COMPLIANCE Federal, Does Not Comply With California Clean Air Idle 0/0 0
Regulations
12XAN OBD COMPLIANCE for 2013 OBD (On Board Diagnostics) 0/0 0
13AUK TRANSMISSION, AUTOMATIC (Allison 3000EVS_P) 5th Generation Controls; 239/31 270
Close Ratio, 6-Speed; With Double Overdrive, Includes Oil Level Sensor, With
Provision for PTO, Less Retarder, With 80,000-lb GVW & GCW Max.
13WBL TRANSMISSION SHIFT CONTROL {Allison) Push -Button Type; for Allison 3000 0/0 0
& 4000 Series Transmission
13WLP TRANSMISSION OIL Synthetic; 29 thru 42 Pints 0/0 0
13WUT ALLISON SPARE INPUT/OUTPUT for Emergency Vehicle Series (EVS); Without 0/0 0
Split Shaft PTO
13WYL SHIFT CONTROL PARAMETERS Allison Performance Programming in Primary 0/0 0
and Allison Economy Programming in Secondary
14899 SUSPENSION AIR CONTROL VALVE Pressure Release Control In Cab 6/2 8
14AGE AXLE, REAR, SINGLE {Dana Spicer 17060S} Single Reduction, 17,500-lb 0/13 13
Capacity, 190 Wheel Ends. Gear Ratio: 4.88
Includes
: REAR AXLE DRAIN PLUG (1) Magnetic, For Single Rear Axle
Notes
: The following features should be considered when calculating Rear GAWR: Rear
Axles; Rear Suspension; Brake System; Brakes, Rear Air Cam; Brake Shoes, Rear;
Special Rating, GAWR; Wheels; Tires.
: When Specifying Axle Ratio, Check Performance Guidelines and TCAPE for
Startability and Performance
14TBN SUSPENSION, REAR, AIR, SINGLE {International} Ride Optimized Suspension 0/-10 -10
(IROS); 18,500-lb Capacity, 5.3" Ride Height, With Shock Absorbers
Notes
: The following features should be considered when calculating Front GAWR: Front
Axles; Front Suspension; Brake System; Brakes, Front Air Cam; Wheels; Tires.
6 Proposal: 11235-01
INTERNATIONAL's
Code
14WLA
TR 12430- Exhibit B
Vehicle Specifications
2014 4300 SBA LP 4X2 (MH025)
Description
AXLE, REAR, LUBE {EmGard 75W-901 Synthetic Oil; 1 thru 29.99 Pints
15SGG FUEL TANK Top Draw; D Style, Non Polished Aluminum, 19" Deep, 70 U.S. Gal.,
265 L Capacity, with Quick Connect Outlet, Mounted Left Side, Under Cab
Notes
: N/A with 19.5" Tires
16196 CAB Conventional 6-Man Crew Cab
Includes
: ARM REST (2) Molded Plastic; One Each Door
: CLEARANCE/MARKER LIGHTS (5) Flush Mounted
: COAT HOOK, CAB Located on Rear Wall, Centered Above Rear Window
: CUP HOLDERS Two Cup Holders, Located in Lower Center of Instrument Panel
: DOME LIGHT, CAB Rectangular, Door Activated and Push On -Off at Light Lens,
Timed Theater Dimming, Integral to Console, Center Mounted
: GLASS, ALL WINDOWS Tinted
: GRAB HANDLE, CAB INTERIOR (1) "A" Pillar Mounted, Passenger Side
: GRAB HANDLE, CAB INTERIOR (2) Front of "B" Pillar Mounted, One Each Side
: GRAB HANDLE, CAB INTERIOR (4) Two Each Side, Rear Door Mounted at Hinge
Side and "C" Pillar Mounted
: INTERIOR SHEET METAL Upper Door (Above Window -Ledge) Painted Exterior
Color
: STEP (8) Two Steps Per Door
Notes
: 43.9" CA Loss
16975 HEATER HOSES Silicone
16990 AIR CONDITIONER, PROVISION FOR Accommodation Package, for Air
Conditioning, Includes (1) SD7 Sanden Auxiliary Compressor in Secondary
Compressor Position and Compressor Drive Effects for Vehicle With Primary
Compressor Mounting
16HBA GAUGE CLUSTER English With English Electronic Speedometer
Inr h iripm
: GAUGE CLUSTER (5) Engine Oil Pressure (Electronic), Water Temperature
(Electronic), Fuel (Electronic), Tachometer (Electronic), Voltmeter
: ODOMETER DISPLAY, Miles, Trip Miles, Engine Hours, Trip Hours, Fault Code
Readout
: WARNING SYSTEM Low Fuel, Low Oil Pressure, High Engine Coolant Temp,
and Low Battery Voltage (Visual and Audible)
16HCL SEATBELT WARNING PREWIRE Includes Seat Belt Switches and Seat Sensors
for all Belted Positions in the Cab and a Harness Routed to the Center of the Dash
for the Aftermarket Installation of the Data Recorder and Seatbelt Indicator
Systems, for 4 to 6 Seat Belts
16HGH GAUGE, OIL TEMP, ALLISON TRAN
16HHE GAUGE, AIR CLEANER RESTRICTION {Filter -Minder} With Black Bezel Mounted
in Instrument Panel
16HKT IP CLUSTER DISPLAY On Board Diagnostics Display of Fault Codes in Gauge
Cluster
16JNV SEAT, DRIVER {National 2000) Air Suspension, High Back With Integral Headrest,
Cloth, Isolator, 1 Chamber Lumbar, 2 Position Front Cushion Adjust, -3 to +14
Degree Back Angle Adjust
October 31, 2013
F/R Wt Tot Wt
(Ibs) (Ibs)
0/0 0
13/2 15
104/250 354
0/0 0
28/-1 27
0/0
0/0
n
N
1/0 1
2/0 2
0/0 0
-16/-9 -25
7
Proposal: 11235-01
INTERNATIONAL'o
TR 12430- Exhibit B
Vehicle Specifications
2014 4300 SBA LP 4X2 (MH025)
October 31, 2013
Code Description F/R Wt Tot Wt
(Ibs) (Ibs)
Includes
: SEAT BELT 3-Point, Lap and Shoulder Belt Type
16LJZ SEAT, REAR {National 20001 Two Individual Outboard Seats, NFPA Compliant, 133/39 172
Air Suspension, High Back, Cloth, Isolator, Lumbar, with 2 Position Front Cushion
Adjustment, -3 to +14 Degree Back Angle Adjust, with 18" Wide Cushion and 20"
Seat Back
Includes
SEAT BELT Two 3-Point Shoulder Belts
16RPX SEAT, PASSENGER {National} Air -Suspension, High Back With Integral Headrest, 60/20 80
Cloth, Isolated, 1 Chamber Lumbar, 2 Position Front Cushion Adjustment, -3 to +14
Degree Seat Back Adjustment
Includes
: SEAT BELT 3-Point, Lap and Shoulder Belt Type
16SDC GRAB HANDLE (2) Chrome Towel Bar Type With Anti -Slip Rubber Inserts; for Cab 6/0 6
Entry, Mounted Left and Right, Each Side at "B" Pillar
16SDU MIRRORS (2) {Lang Mekra} Styled; Rectangular, 7.09" x 15.75" & Integral Convex 8/0 8
Both Sides, 102" Inside Spacing, Breakaway Type, Heated Heads Thermostatically
Controlled, Power Both Sides, Clearance Lights LED, Bright Finish Heads &
Brackets
16VCA SEAT BELT All Red; 4 to 6 0/0 0
16VCN KEYLESS ENTRY SYSTEM REMOTE With Panic Alarm and Horn Beep Lock 1/0 1
Confirmation, With Auxiliary Button for Work Light Function Includes One Key Fob
16WBY
ARM REST, RIGHT, DRIVER SEAT
3/0
3
16WBZ
ARM REST, LEFT, PASSENGER SEAT
3/0
3
16WCT
AIR CONDITIONER {Blend -Air} With Integral Heater & Defroster
67/4
71
Inr h iriac
: HEATER HOSES Premium
: HOSE CLAMPS, HEATER HOSE Mubea Constant Tension Clamps
: REFRIGERANT Hydrofluorocarbon HFC-134A
16WHJ
HOSE CLAMPS, HEATER HOSE {Breeze} Belleville Washer Type
0/0
0
16WJS
INSTRUMENT PANEL Center Section, Flat Panel
0/0
0
16WJV WINDOW, POWER (4) And Power Door Locks, Front and Rear Doors, Left and 10/0 10
Right, Includes Express Down Feature
16WKY
HVAC FRESH AIR FILTER
4/0
4
16WLS
FRESH AIR FILTER Attached to Air Intake Cover on Cowl Tray in Front of
1/0
1
Windshield Under Hood
16WSE
LOW WASHER FLUID INDICATOR
1/0
1
16WSJ
CAB INTERIOR TRIM Premium; for Crew Cab
0/0
0
Includes
: "A" PILLAR COVER Molded Plastic
: CAB INTERIOR TRIM PANELS Cloth Covered Molded Plastic, Full Height; All
Exposed Interior Sheet Metal is Covered Except for the Following: with a Two -Man
Passenger Seat or with a Full Bench Seat the Back Panel is Completely Void of
Covering
8 Proposal: 11235-01
INTERNATIONAL'
TR 12430- Exhibit B
Vehicle Specifications
2014 4300 SBA LP 4X2 (MH025)
October 31, 2013
Code Description F/R Wt Tot Wt
(Ibs) (lbs)
: CAB SOUND INSULATION Includes Dash and Engine Cover Insulators
: CONSOLE, OVERHEAD Molded Plastic; With Dual Storage Pockets with
Retainer Nets, CB Radio Pocket, Speakers, and Reading Lights
: COURTESY LIGHT (4) Mounted In Front and Rear Map Pockets - Left and Right
Sides
: DOOR TRIM PANELS with Cloth Insert on Bolster Driver and Passenger Doors
: FLOOR COVERING Rubber, Black
: GAUGE, TEMPERATURE, AMBIENT Includes Wiring and Sensor With Display
Unit Mounted in Cluster
: HEADLINER Soft Padded Cloth
: INSTRUMENT PANEL TRIM Molded Plastic with Black Center Section
: STORAGE POCKET, DOOR (2) Molded Plastic (Carpet Texture), Full -Length;
Driver and Passenger Doors
: SUN VISOR (3) Padded Vinyl: 2 *Moveable (Front -to -Side) Primary Visors, Driver
Side with Vanity Mirror and Toll Ticket Strap, plus 1 Auxiliary Visor (Front Only),
Driver Side
16WSK CAB REAR SUSPENSION Air Bag Type 33/11 44
27DMC WHEELS, FRONT DISC; 22.5" Polished Aluminum, 10-Stud (285.75MM BC) Hub -208/0 -208
Piloted, Flanged Nut, Metric Mount, 8.25 DC Rims; With Steel Hubs
Notes
: Aluminum Wheels not Painted or Coated
: Compatible Tire Sizes: 11 R22.5, 12R22.5, 255/70R22.5, 255/80R22.5,
265/75R22.5, 275/70R22.59 275/80R22.57 295/75R22.51 295/80R22,5
28DMC WHEELS, REAR DUAL DISC; 22.5" Polished Aluminum, 10-Stud (285.75MM BC) 0/163 163
Hub Piloted, Flanged Nut, Metric Mount, 8.25 DC Rims; With Steel Hubs
Notes
: Aluminum Wheels not Painted or Coated
: Compatible Tire Sizes: 11 R22.5, 12R22.5, 255/70R22.5, 255/80R22.5,
265/75R22.5, 275/70R22.57 275/80R22.57 295/75R22.51 295/80R2275
: Polished Surface Outside Dual Only
29580
WHEEL SEALS, FRONT
{International)
Oil -Lubricated Wheel Bearings
0/0
0
29ACD
TIRE VALVE CAP Flo-Thru Design
0/0
0
29WLA
WHEEL BEARING, FRONT, LOBE {EmGard 50W) Synthetic Oil
0/0
0
60ACW BDY INTG,I/O EXPANSION HARNESS {for Diamond Logic Builder) In -Cab wire 1/0 1
harness (DLB) program only, Includes a harness with five blunt cut wires routed on
lower left of instrument panel. Two ground active inputs and two (.5Amp) relay
drivers outputs are provided
7702618102 (4) TIRE, REAR 265/75R22.5 G622 RSD (GOODYEAR) 534 rev/mile, load range 0/88 88
G, 14 ply
7702618107 (2) TIRE, FRONT 265/75R22.5 G661 HSA (GOODYEAR) 539 rev/mile, load range 54/0 54
G, 14 ply
Total Component Weight: 7748/3791 11539
GROVER AIR HORNS MTD. ON HOOD 0/0 0
AUXILIARY AIR TANK W/ CHECK VALVE AND PLUMB TO THE EXISTING AIR 0/0 0
TANK, BUT DEDICATE AUXILIARY AIR TANK TO BE USED FOR THE AIR
HORNS
WHEELBASE MODIFICATION TO 112" C/A 0/0 0
9 Proposal: 11235-01
INTERNATIONAL®
Code
TR 12430- Exhibit B
Vehicle Specifications
2014 4300 SBA LP 4X2 (MH025)
Description
150 DAY TERMS - FROM INT'L FACTORY INVOICE DATE
ADDITIONAL LEVELING VALVE
FURNISH & INSTALL (2) ARM RESTS FOR THE REAR SEATS.
RED DOT A/C UNIT
Total Goods Purchased:
October 31, 2013
F/R Wt Tot Wt
(Ibs) (Ibs)
0/0 0
0/0 0
0/0 0
0/0 0
0/0 0
The weight calculations included in this proposal are an estimate of future vehicle weight. The actual weight as manufactured may be
different from the estimated weight. Navistar, Inc. shall not be liable for any consequences resulting from any differences between the
estimated weight of a vehicle and the actual weight.
10 Proposal: 11235-01
TR 12430- Exhibit B
I NTERNATIONAL®
Description
Net Sales Price:
Financial Summary
2014 4300 SBA LP 4X2 (MH025)
(US DOLLAR)
Price
$95,429.00
October 31, 2013
Please feel free to contact me regarding these specifications should your interests or needs change. I am confident you will be
pleased with the quality and service of an International vehicle.
Approved by Seller:
Official Title and Date
Authorized Signature
This proposal is not binding upon the seller without
Seller's Authorized Signature
Accepted by Purchaser:
C i-h of Tame
Authorized Signatu
Nti ftW Q Coloch
e
nd Date
Official Title and Date
The TOPS FET calculation is an estimate for reference purposes only. The seller or retailer is responsible for calculating
and reporting/paying appropriate FET to the IRS.
11 Proposal: 11235-01
TR 12430- Exhibit B
INTERNATIONAL®
Turning Radius Summary
2014 4300 SBA LP 4X2 (MIH025)
PW
1
i CENTER � 1
! 1
Turning I
i Radius:
9'� I
! !A Curd 3 3 !
Clearance: I
� � I
i W 11 I 1
� ! i
� � 1
C: 14.97
CH: 0
CI: 5.28
TR: 3 2' g ��
TR CR
C R: 3 3' 3"
TW: 10. 00
Series:
Model:
Description:
Model Year:
4000
MH025
4300 SBA LP 4X2
2014
Calculation Factors
Wheelbase: 236
October 31, 2013
Front Axle: 0002ARX
Description: AXLE, FRONT NON -DRIVING, (Meritor MFS-10-143A)
Wide Track, I -Beam Type, 10,000-lb Capacity
Front Wheel: 0027DMC
Description: WHEELS, FRONT, DISC; 22.5" Polished Aluminum, 10-Stud
(285.75MM BC) Hub Piloted, Flanged Nut, Metric Mount,
8.25 DC Rims; With Steel Hubs
Front Tire: 07702618107
Description: TIRES, 265/75R22.5 G661 HSA (GOODYEAR) 539 rev/
mile, load range G, 14 ply
Steering Gear: 0005PSM
Description: STEERING GEAR, {Sheppard HD941 Power
Turning Radius Statistics
General Information
Inside Turn Angle:
Radial Overhang:
Axle Information
KingPin Inclination:
KingPin Center:
48 Degrees
19
6.25 Degrees
71.5
Turning Radius - Curb View
C - Curb Contact Length: 14.97
Cl - Curb Clearance Increment: 5.28
CR - Curb Clearance Radius: 3313"
CH - Curb Height: 6"
TR - Turning Radius: 3219"
TW - Tire Width: 10.00
* All Measurements are in inches,..unless otherwise specified.
This information is based on engineering information available at this time. Actual figures may vary. Navistar, Inc. cannot accept
liability for consequences due to this variance.
12 Proposal: 11235-01
0
343:1. NW 27th Avenue + Ocala, Florida 34475
Office: 352-629-6305 . Fax: 352-629-20.8
Tall. Free: 1-800-524-6072
AMBULANCE PROPOSAL
DATE: November 7, 2013
This Proposal has been prepared for:
Steve Stillwell
Tamarac Fire Rescue
6000 North Hiatus Road
Tamarac, FL 33321
We propose to furnish to you two (2) 2014 Horton model 623 rescue units on a 2014 International 430OLP crew
cab chassis, to be custom built and equipped in accordance with the requirements of the Tamarac Fire Rescue
department. Pricing is based on Florida Sheriffs Association Contract #11-10-1202, specification 02.
Delivery will be F.Q.B. Tamarac, FL and will be approximately 240-280 days from receipt of purchase order.
Terms of payment shall be cash on delivery (COD) when unit arrive at Tamarac Fire Rescue, facility.
Prepayment discounts are available.
The current purchase price for the specified Ambulance is $273,458.00 each. This proposal shall expire
December 31, 2013 unless extended in writing.
This proposal is deemed acceptable by the undersigned. In witness whereof, The Company and the Purchaser
shall execute an agreement to this proposal with signatures from authorized representatives as of the date set
forth by each.
Total price each unit:
Total Price for two units:
Company:
Br: �H�4"
Title: Ambulance Sales Manager
Date: November 7, 2013
$2739458oOO
$546,916s00
Purchaser:
Michael C. Cemech
Title: ram . A4&V4...._
Date:
Drawings submitted are for reference only. Pricing is based on enclosed written specifications.
Quote#11747, Revision 2
,Horton
- ------- --- - - ----- --
EMERGENCY VEHICLES
jFAff�
"VCe
TR 12430- Exhibit D
1 0 $ PffA I f 'A
al 4P y4p
ANNOUNCEMENT
11- 10-1202
FIRE RESCUE VEHICLES
& OTHER FLEET EQUIPMENT
Participating Law Enforcement, Fire/Rescue
8Z Local Governmental
Agencies of the State of Florida
Coordinated By
The
Florida Fire Chiefs' Association,
Florida Sheriffs Association 8r
Florida Association of Counties
FLORIDA.
ASOCL -kTt N :L
COUNTIES
All About Florida
TR 12430- Exhibit D
TABLE OF CONTENTS
Effective Dates & Ordering Instructions........................................................................................ 10
Overview of Awarded Specifications............................................................................................... 11
Awarded Manufacturers/Dealers.................................................................................................. 29
Basic Information REQUIRED for Purchase Orders....................................................................... 31
Specification #01 -Type I Ambulance - 4x2.................................................................................. 32
FordXLT F-350................................................................................................................. 34
FordXLT F-450................................................................................................................. 35
FordXLT F-550................................................................................................................. 36
ChevySilverado 3500 HD.................................................................................................. 37
DodgeRam 3500............................................................................................................... 38
DodgeRam 4500............................................................................................................... 39
DodgeRam 5500............................................................................................................... 40
Specification #02 -'Type I Ambulance, Medium Duty - 4x2........................................................... 41
FordF-650........................................................................................................................ 43
FreightlinerM2.....................................................................,............................................ 44
InternationalTerrastar SFA............................................................................................... 45
International Durastar 4300M7......................................................................................... 46
International Durastar 430OLP.......................................................................................... 47
International Durastar 440OLP.......................................................................................... 48
SpartanMetro Star RT...................................................................................................... 49
Specification #03 -Type II Ambulance, Van - 4x2........................................................................ 50
FordE-350........................................................................................................................ 52
Sprinter..........................................................................................................................53
Specification #04 -Type III Ambulance - 4x2................................................................................ 54
FordXL E-350.................................................................................................................... 56
FordXL E-450................................................................................................................... 57
ChevyG3500..................................................................................................................... 58
ChevyG4500..................................................................................................................... 59
GMCG3500...................................................................................................................... 60
GMCG4500...................................................................................................................... 61
Sprinter..........................................................................................................................62
Specification #05 - 75' Mid Mounted Aerial Apparatus.................................................................. 63
Formed Stainless Steel Body
Aluminum Ladder
Sutphen Corporation - Sutphen SL75................................................................. 68
Specification #06 - 75' Rear Mounted Aerial Apparatus................................................................. 69
Extruded Aluminum Body
Aluminum Ladder
Hall -Mark Fire Apparatus (E-ONE) - E-ONE HP 75............................................. 74
TR 12430- Exhibit D
Specification #06 - 75' Rear Mounted Aerial Apparatus (continued)
Steel Ladder
Crimson Fire (Public Safety...) - Crimson 75RMA................................................
FerraraFire Apparatus, Inc. - Igniter XD............................................................
Ferrara Fire Apparatus, Inc. - Intruder...............................................................
Rosenbauer South Dakota, LLC - Spartan Metro Star 759 ...................................
Formed Aluminum Body
Aluminum Ladder
Pierce Manufacturing, Inc. - Pierce Impel 75' HDL..............................................
Steel Ladder
American LaFrance, LLC - American LaFrance 75RML.......................................
Crimson Fire (Public Safety...) - Crimson 75RMA................................................
Kovatch Mobile Equip. Corp. (KME) - KME Predator AerialCat FL0675................
Pierce Manufacturing, Inc. - Pierce Impel 75' HDL..............................................
Rosenbauer South Dakota, LLC - Spartan Metro Star 750 ...................................
Formed Stainless Steel Body
Steel Ladder
75
75
75
75
W
77
77
77
77
77
American LaFrance, LLC - American LaFrance 75RML....................................... 78
Crimson Fire (Public Safety...) - Crimson 75RMA................................................ 78
Specification #07 - 100' Mid Mounted Aerial Apparatus................................................................ 79
Extruded Aluminum Body
Steel Ladder
Ferrara Fire Apparatus, Inc.
Ferrara Fire Apparatus, Inc.
Formed Aluminum Body
Steel Ladder
- Igniter XD............................................................ 84
- Spectr.................................................................. 84
Kovatch Mobile Equip. Corp. (KME) - KME Predator AerialCat FL07100.............. 85
Pierce Manufacturing, Inc. - Pierce Arrow XT HDL.............................................. 85
Formed Stainless Steel . Body
Aluminum Ladder
Sutphen Corporation - Sutphen SL 100............................................................... 86
Specification #08 - 100' Rear Mounted Aerial Apparatus............................................................... 87
Extruded Aluminum Body
Aluminum Ladder
Hall -Mark Fire Apparatus (E-ONE) - E-ONE HP 100L......................................... 92
Steel Ladder
Crimson Fire (Public Safety...) - Crimson 100RMA.............................................. 93
Ferrara Fire Apparatus, Inc. - Igniter XD............................................................ 93
Ferrara Fire Apparatus, Inc. - Spectr.................................................................. 93
Rosenbauer South Dakota, LLC - Spartan Gladiator 100'................................... 93
Formed Aluminum Body
Aluminum Ladder
Pierce Manufacturing, Inc. - Pierce Arrow XT HDL.............................................. 94
Steel Ladder
American LaFrance, LLC - American LaFrance 100RMA..................................... 95
Kovatch Mobile Equip. Corp. (KME) - KME Predator AerialCat FL08103.............. 95
Pierce Manufacturing, Inc. - Pierce Arrow XT HDL.............................................. 95
Rosenbauer South Dakota, LLC - Spartan Gladitor 100'..................................... 95
Formed Stainless Steel Body
Aluminum Ladder
Pierce Manufacturing, Inc. - Pierce Arrow XT HAL-SS......................................... 96
TR 12430- Exhibit D
Specification #08 - 100' Rear Mounted Aerial Apparatus (continued)
Formed Stainless Steel Body
Steel Ladder
American LaFrance, LLC - American LaFrance 100RMA..................................... 97
Crimson Fire (Public Safety...) - Crimson 10ORMA.............................................. 97
Specification #09 - Mid Mounted Aerial Platform.......................................................................... 98
Extruded Aluminum Body
Aluminum Ladder
Hall -Mark Fire Apparatus (E-ONE) - E-ONE HP 95 MM.................................... 103
Steel Ladder
Crimson Fire (Public Safety...) Crimson MM 1009
............................................
Ferrara Fire Apparatus, Inc. - Igniter XD..........................................................
Ferrara Fire Apparatus, Inc. - Spectr............................................................... 0
Rosenbauer South Dakota, LLC - Spartan Gladiator .........................................
Formed Aluminum Body
Steel Ladder
American LaFrance, LLC - American LaFrance 1 OOMMP...................................
Kovatch Mobile Equip. Corp. (KME) - KME Predator AerialCat FL09100............
Pierce Manufacturing, Inc. - Pierce Arrow XT Mid Mount ..................................
Rosenbauer South Dakota, LLC - Spartan Gladitor...........................................
Formed Stainless Steel Body
Aluminum Ladder
104
104
104
104
105
105
105
105
Sutphen Corporation - SPH 100........................................................................ 106
Sutphen Corporation - SP 110........................................................................... 106
Steel Ladder
American LaFrance, LLC - American LaFrance 1 OOMMP................................... 107
Crimson Fire (Public Safety...) - Crimson MM 100............................................ 107
Specification # 10 - Rear Mounted Aerial Platform....................................................................... 108
Extruded Aluminum Body
Aluminum Ladder
Hall -Mark Fire Apparatus jr-ONE) - E-ONE HP 100P....................................... 113
Steel Ladder
Crimson Fire (Public Safety...) - Crimson Star RM 100'.....................................
Ferrara Fire Apparatus, Inc. - Igniter XD..........................................................
Ferrara Fire Apparatus, Inc. - Spectr................................................................
Rosenbauer South Dakota, LLC - Spartan Gladiator .........................................
Formed Aluminum Body
Aluminum Ladder
Pierce Manufacturing,. Inc. - Pierce Arrow XT Rear Mount PAP ..........................
Steel Ladder
American LaFrance, LLC - American LaFrance 100RMP...................................
Kovatch Mobile Equip. Corp. (KME) - KME Predator AerialCat FLO 10102...0......
Pierce Manufacturing, Inc. - Pierce Arrow XT Rear Mount PAP ..........................
Rosenbauer South Dakota, LLC - Spartan Gladitor...........................................
Formed Stainless Steel Body
Steel Ladder
114
114
114
114
115
116
116
116
116
American LaFrance, LLC - American LaFrance 100RMP................................... 117
Crimson Fire Public Safety...) - 9
( Crimson Star RM 100..................................... 117
TR 12430- Exhibit D
Specification # 11 - Medium Duty Rescue Apparatus - 4x2.......................................................... 118
Extruded Aluminum Body
FreightlinerM2-106.................................................................................................
121
Crimson Fire (Public Safety...) - Crimson Star MR ............................................
121
Ferrara Fire Apparatus, Inc. - FFA 108 MDR Rescue ........................................
121
Hall -Mark Fire Apparatus (E-ONE) - E-ONE REHN...........................................
121
Rosenbauer South Dakota, LLC - FSA Rescue 11.............................................
121
Wheeled Coach Industries, Inc. - Rescue Force FLS 11 FTLNR ............................
121
InternationalDurastar. ...:.........................................................................................
1 22
Crimson Fire (Public Safety...) - Crimson Star MR ............................................
122
Ferrara Fire Apparatus, Inc. - FFA 108 MDR Rescue ........................................
122
Hall -Mark Fire Apparatus (E-ONE) - E-ONE REHN...................0.........0.............
122
Rosenbauer South Dakota, LLC - FSA Rescue 11.............................................
122
Wheeled Coach Industries, Inc. - Rescue Force FLS 11INTL ...............................
12
Formed Aluminum Body
Freightliner M2-106.................................................................................................
1 23
American LaFrance, LLC - American LaFrance 16' W/AR..................................123
Kovatch Mobile Equip. Corp. (KME) - KME FL 11 MDR .......................................
123
Pierce Manufacturing, Inc. - Pierce MDR.. ........ too ... 4 .................... 0 . 0 ..... too ...........
123
Rosenbauer South Dakota, LLC - FSA Rescue 11 ..............0........0..................0..
123
Toyne, Inc. (Southeastern...) - Toyne Medium Rescue.. .. o - - - - - , - o o o .... o-o4 ........ o ... o
123
InternationalDurastar.............................................................................................
124
American LaFrance, LLC - American LaFrance 16' W/AR.................................
124
Kovatch Mobile Equip. Corp. (KME) - KME FL 11 MDR.. o o ................. o...o ..... o .......
124
Pierce Manufacturing, Inc. - Pierce MDR ..........................................................
124
Rosenbauer South Dakota, LLC - FSA Rescue 11.............................................
124
Sutphen Corporation - Sutphen CR Series Rescue .............. 0.0 ...........................
124
Toyne, Inc. (Southeastern...) - Toyne Medium Rescue.... ......... o o ....................... o
124
Specification # 12 - Heavy Rescue Apparatus............................................................................... 125
Extruded Aluminum Body
Crimson Fire (Public Safety...) - Crimson Star HR.................................................... 128
Ferrara Fire Apparatus, Inc. - Igniter XD YMFD...................................................... 128
Ferrara Fire Apparatus, Inc. - Intruder MFDXL........................................................ 1
28
Hall -Mark Fire Apparatus (E-ONE) - E-ONE REHN lyphoon.................................... 128
Rosenbauer South Dakota, LLC - Spartan Force ...................................................... 12
Formed Aluminum Body
American LaFrance, LLC - American LaFrance 18' W/ACR....................................... 129
Kovatch Mobile Equip. Corp. (KME) - KME Predator FL12HDR................................. 129
Pierce Manufacturing, Inc. - Pierce Saber HDR........................................................ 129
Rosenbauer South Dakota, LLC - Spartan Force ...................................................... 129
Sutphen Corporation - Sutphen R Series................................................................. 129
Toyne, Inc. (Southeastern...) - Spartan Heavy Rescue ............................................... 129
Specification # 13 - 2500 Gallon Mobile Water Supply Fire Apparatus - 2 Door ............................ 130
Extruded Aluminum Body
FreightlinerM2-106................................................................................................. 134
Crimson Fire (Public Safety...) - Crimson Star Tanker ....................................... 134
Ferrara Fire Apparatus, Inc. - FFA T2500 Tanker ............................................. 134
Hall -Mark Fire Apparatus (E-ONE) - E-ONE TTSA............................................ 134
InternationalWorkstar............................................................................................. 135
Crimson Fire (Public Safety...) - Crimson Star Tanker... ..................................... 135
Ferrara Fire Apparatus, Inc. - FFA T2500 Tanker ............................................. 135
Hall -Mark Fire Apparatus (E-ONE) - E-ONE TrSA............................................ 135
TR 12430- Exhibit D
Specification # 13 - 2500 Gallon Mobile Water Supply Fire Apparatus - 2 Door (continued)
Formed Aluminum Body
FreightlinerM2-106.................................................................................................
136
American LaFrance, LLC - American LaFrance T/A Tanker ...............................
136
Kovatch Mobile Equip. Corp. (KME) - KME Flatback FL132500 .........................
136
Pierce Manufacturing, Inc. - Pierce Contender Series ........................................
136
Rosenbauer South Dakota, LLC - FSA Tanker 13.............................................
136
Toyne, Inc. (Southeastern...) - Toyne FFCSA-2500............................................
136
InternationalWorkstar.............................................................................................
137
American LaFrance, LLC - American LaFrance T/A Tanker ...............................
137
Kovatch Mobile Equip. Corp. (KME) - KME Flatback FL132500 .........................
137
Pierce Manufacturing, Inc. - Pierce Contender Series ........................................
137
Rosenbauer South Dakota, LLC - FSA Tanker 13.............................................
137
Toyne, Inc. (Southeastern...) - Toyne FFCSA-2500............................................
137
Formed Galvanneal Steel Body
FreightlinerM2-106.................................................................................................
138
Kovatch Mobile Equip. Corp. (KME) - KME Flatback FL132500 .........................
138
International Workstar.............................................................................................
139
Kovatch Mobile Equip. Corp. (KME) - KME Flatback FL132500 .........................
139
Formed Stainless Steel Body
FreightlinerM2-106..................................................................................................
140
Crimson Fire (Public Safety...) - Crimson Star Tanker .......................................
140
Kovatch Mobile Equip. Corp. (KME) - KME Flatback FL132500 .........................
140
Toyne, Inc. (Southeastern...) - Toyne FFCSA-2500............................................
140
InternationalWorkstar.............................................................................................
141
Crimson Fire (Public Safety...) - Crimson Star Tanker .......................................
141
Kovatch Mobile Equip. Corp. (KME) - KME Flatback FL132500 .........................
141
Sutphen Corporation - Sutphen CTS-2500 Tanker ...........................................
141
Toyne, Inc. (Southeastern...) - Toyne FFCSA-2500............................................
141
Specification # 14 - Wildland Fire Apparatus............................................................................... 142
FordF-550...................................................................................................................... 145
American LaFrance, LLC - Wildland Brush ....................................................... 145
Ferrara Fire Apparatus, Inc. - Wildland Brush .................................................. 145
Hall -Mark Fire Apparatus (E-ONE) - Wildland.................................................. 145
Kovatch Mobile Equip. Corp. (KME) - KME WildlandFL 14WFA .......................... 145
Pierce Manufacturing, Inc. - Pierce F550 Wildland............................................ 145
Toyne, Inc. (Southeastern...) - Wildland Brush ................................................. 145
DodgeRam 5500............................................................................................................. 146
American LaFrance, LLC - Wildland Brush ....................................................... 146
Ferrara Fire Apparatus, Inc. - Wildland Brush .................................................. 146
Hall -Mark Fire Apparatus (E-ONE) - Wildland.................................................. 146
Kovatch Mobile Equip. Corp. (KME) - KME Wildland FL MVWFA ......................... 146
International Durastar 4300M7....................................................................................... 147
American LaFrance, LLC - Wildland Brush ....................................................... 147
Kovatch Mobile Equip. Corp. (KME) - KME Wildland FL 14WFA ......................... 147
Toyne, Inc. (Southeastern...) - Wildland Brush ................................................. 147
Specification # 15 - Commercial Pumper - 2 Door........................................................................ 148
Extruded Aluminum Body
FreightlinerM2-106................................................................................................. 151
Crimson Fire (Public Safety...) - Crimson Star Pumper ...................................... 151
Ferrara Fire Apparatus, Inc. - FFA RP751 Pumper ............................................ 151
Hall -Mark Fire Apparatus (E-ONE) - E-ONE TDPM........................................... 151
Rosenbauer South Dakota, LLC - FSA Pumper 13............................................ 151
TR 12430- Exhibit D
Specification # 15 - Commercial Pumper - 2 Door (continued)
Extruded Aluminum Body
International Durastar.............................................................................................
152
Crimson Fire (Public Safety...) - Crimson Star Pumper ......................................
152
Ferrara Fire Apparatus, Inc. - FFA RP751 Pumper ............................................
152
Hall -Mark Fire Apparatus (E-ONE) - E-ONE TDPM...........................................
152
Rosenbauer South Dakota, LLC - FSA Pumper 13............................................
152
Sutphen Corporation - Sutephen C 1 Pumper ....................................................
152
Formed Aluminum Body
FreightlinerM2-106.................................................................................................
153
American LaFrance, LLC - American LaFrance S/M Pumper .............................
153
Crimson Fire (Public Safety...) - Crimson Star Pumper ......................................
153
Kovatch Mobile Equip. Corp. (KME) - KME Challenger FL15COML....................
153
Pierce Manufacturing, Inc. - Pierce Contender Series ........................................
153
Rosenbauer South Dakota, LLC - FSA Tanker 13.............................................
153
Toyne, Inc. (Southeastern...) - Toyne FFCSA Pumper ........................................
153
InternationalDurastar.............................................................................................
154
American LaFrance, LLC - American LaFrance S/M Pumper .............................
154
Crimson Fire (Public Safety... ) - Crimson Star Pumper ......................................
154
Kovatch Mobile Equip. Corp. (KME) - KME Challenger FL15COML....................
154
Pierce Manufacturing, Inc. - Pierce Contender Series ........................................
154
Rosenbauer South Dakota, LLC - FSA Tanker 13..............................................
154
Toyne, Inc. (Southeastern...)
- Toyne
FFCSA Pumper ........................................
154
Formed Galvanneal Steel Body
FreightlinerM2-106.................................................................................................
155
Kovatch Mobile Equip. Corp.
(KME) -
KME Challenger FL 15COML....................
155
International Workstar.............................................................................................
156
Kovatch Mobile Equip. Corp.
(KME) -
KME Challenger FL15COML....................
156
Formed Stainless Steel Body
FreightlinerM2-106.................................................................................................
157
American LaFrance, LLC - American
LaFrance S/M Pumper .............................
157
Crimson Fire (Public Safety...)
- Crimson Star Pumper ......................................
157
Hall -Mark Fire Apparatus (E-ONE)
-
E-ONE PSTS............................................
157
Kovatch Mobile Equip. Corp.
(KME) -
KME Challenger FL15COML....................
157
Toyne, Inc. (Southeastern...)
- Toyne
FFCSA Pumper ........................................
157
InternationalDurastar.............................................................................................
158
American LaFrance, LLC - American
LaFrance S/M Pumper .............................
158
Crimson Fire (Public Safety...)
- Crimson Star Pumper ......................................
158
Hall -Mark Fire Apparatus (E-ONE)
-
E-ONE PSTS............................................
158
Kovatch Mobile Equip. Corp.
(KME) -
KME Challenger FL 15COML....................
158
Toyne, Inc. (Southeastern...)
- Toyne
FFCSA Pumper ........................................
158
Specification # 16 - Level I Custom Pumper - 4 Door................................................................... 159
Custom Chassis
ExtrudedAluminum Body........................................................................................ 162
Hall -Mark Fire Apparatus (E-ONE) - E-ONE Typhoon Pumper .......................... 162
Sutphen Corporation - S-Series Custom........................................................... 162
FormedAluminum Body.......................................................................................... 163
Kovatch Mobile Equip. Corp. (KME) - KME Challenger FLI 6LVL1 ..................... 163
Pierce Manufacturing, Inc. - Pierce Saber Series ............................................... 163
Sutphen Corporation - S-Series Custom........................................................... 163
Formed Galvanneal Steel Body................................................................................. 164
Kovatch Mobile Equip. Corp. (KME) - KME Challenger FL 16LVL 1 ..................... 164
Pierce Manufacturing, Inc. - Pierce Velocity SLT Series ..................................... 164
TR 12430- Exhibit D
Specification # 16 - Level I Custom Pumper - 4 Door (continued)
FormedStainless Steel Body....................................................................................
165
Hall -Mark Fire Apparatus (E-ONE) - E-ONE typhoon Pumper ..........................
165
Kovatch Mobile Equip. Corp. (KME) - KME Challenger FL 16LVL 1 .....................
165
Pierce Manufacturing, Inc. - Pierce Impel SS Series ..........................................
165
Spartan Chassis
ExtrudedAluminum Body........................................................................................
166
Crimson Fire (Public Safety...) - Crimson Metro Star Pumper L1.......................
166
Rosenbauer South Dakota, LLC - Spartan Force 16..........................................
166
FormedAluminum Body..........................................................................................
167
Crimson Fire (Public Safety...) - Crimson Metro Star Pumper L1.......................
167
Rosenbauer South Dakota, LLC - Spartan Force 16..........................................
167
Toyne, Inc. (Southeastern...) - Toyne Spartan Metro Star FFCSA ......................
167
Formed Stainless Steel Body....................................................................................
168
Crimson Fire (Public Safety...) - Crimson Metro Star Pumper L1.......................
168
Toyne, Inc. (Southeastern...) - Toyne Spartan Metro Star FFCSA ......................
168
HME Chassis
ExtrudedAluminum Body........................................................................................
169
Ferrara Fire Apparatus, Inc. - Intruder.............................................................
169
FormedAluminum Body..........................................................................................
170
Toyne, Inc. (Southeastern...) - Toyne 1871W FFCSA.........................................
170
Formed Stainless Steel Body....................................................................................
171
Toyne, Inc. (Southeastern...) - Toyne 1871W FFCSA..........................:..............
171
American LaFrance Chassis
FormedAluminum Body..........................................................................................
172
American LaFrance, LLC - American LaFrance Custom S/M Pumper ................
172
Formed Stainless Steel Body....................................................................................
173
American LaFrance, LLC - American LaFrance Custom S/M Pumper ................
173
Specification # 17 - Level II Custom Pumper - 4 Door.................................................................. 174
Custom Chassis
Extruded Aluminum Body........................................................................................ 178
Ferrara Fire Apparatus, Inc. - Igniter XD LFD................................................... 178
Hall -Mark Fire Apparatus (E-ONE) - E-ONE Cyclone Pumper ........................... 178
Rosenbauer South Dakota, LLC - Commander FSA 17..................................... 178
Sutphen Corporation - Monarch Series Custom ................................................ 178
FormedAluminum Body.......................................................................................... 179
Kovatch Mobile Equip. Corp. (KME) - KME Flatback FL 17LVL2 ........................ 179
Pierce Manufacturing, Inc. - Pierce Arrow XT Series ......................................... 179
Rosenbauer South Dakota, LLC - Commander FSA 17..................................... 179
Formed Galvanneal Steel Body.........................................................0....................... 1 80
Kovatch Mobile Equip. Corp. (KME) - KME Flatback FL 17LVL2 ........................ 180
Pierce Manufacturing, Inc. - Pierce Quantum Series ......................................... 180
Formed Stainless Steel Body... .... ..... o o ................... o ................... ............... 181
Hall -Mark Fire Apparatus (E-ONE) - E-ONE Cyclone Pumper ........................... 181
Kovatch Mobile Equip. Corp. (KME) - KME Flatback FL 17LVL2 ........................ 181
Pierce Manufacturing, Inc. - Pierce Velocity Series ............................................ 181
Spartan Chassis
Extruded Aluminum Body. ........ o ........ o ................... o ................................................. 182
Crimson Fire (Public Safety...) - Crimson Metro Star Pumper L2 ....................... 182
Rosenbauer South Dakota, LLC - Spartan Gladiator 17.................................... 182
FormedAluminum Body.... o ...... o ................................. 0 ............ ............ 0#0000000000* 183
Crimson Fire (Public Safety...) - Crimson Metro Star Pumper L2 ....................... 183
Rosenbauer South Dakota, LLC - Spartan Gladiator 17.................................... 183
Toyne, Inc. (Southeastern...) - Toyne Spartan Gladiator.......................0............ 183
TR 12430- Exhibit D
Specification # 16 - Level I Custom Pumper - 4 Door (continued)
Spartan Chassis
Formed Stainless Steel Body.................................................................................... 184
Crimson Fire (Public Safety...) - Crimson Metro Star Pumper L2 ....................... 184
Toyne, Inc. (Southeastern...) - Toyne Spartan Gladiator .................................... 184
HME Chassis
Extruded Aluminum Body........................................................................................ 185
Ferrara Fire Apparatus, Inc. - Spectr LFD......................................................... 185
FormedAluminum Body.......................................................................................... 186
Toyne, Inc. (Southeastern...) - Toyne Spectr..................................................... 186
Formed Stainless Steel Body.................................................................................... 187
Toyne, Inc. (Southeastern...) - Toyne Spectr..................................................... 187
American LaFrance Chassis
Formed Aluminum Body.......................................................................................... 188
American LaFrance', LLC - American LaFrance Custom Rescue Pumper............ 188
Formed Stainless Steel Body.................................................................................... 189
American LaFrance, LLC - American LaFrance Custom Rescue Pumper............ 189
MearsMotor Leasing................................................................................................................... 190
Enterprise Fleet Management..................................................................................................... 191
TR 12430- Exhibit D
FLORIDA SHERIFFS ASSOCIATION
P. O. Box 12519 * Tallahassee, FL 32317-2519
PHONE (850) 877-2165 • FAX (850) 878-8665
WEB SITE: www.flsheriffs.org
DATE: January 1, 2012
TO: ALL PROSPECTIVE PARTICIPANTS
FROM: Steve Casey Lynn Meek Peggy Goff
Executive Director Vehicle Bid Coordinator Vehicle Contract Manager
RE: PARTICIPATING LAW ENFORCEMENT, FIRE/RESCUE &
LOCAL GOVERNMENTAL AGENCIES OF THE STATE OF FLORIDA
COOPERATIVE BID FOR FIRE/RESCUE VEHICLES & OTHER FLEET EQUIPMENT
Bid No, 11-10-1202
We are pleased to announce that the Florida Fire Chiefs' Association, the Florida Sheriffs Association
and the Florida Association of Counties has successfully conducted its tenth statewide competitive
bid for fire & rescue vehicles. Bids will be extended and guaranteed to any and all units of local
governments/political subdivisions including but not limited to county, local county board of public
instruction, municipalities and other local public or public safety agencies or authorities within the
State of Florida.
In addition to the eligible users referenced above and with th4
purchases may be made under the terms and conditions of tf.
located outside the State of Florida. Appropriate governmental
regulations shall apply to purchases made under this contract.
consent of the successful bidder(s)
Is contract by governmental entities
entities' purchasing laws, rules and
This contract is effective January 1, 2012 thru December 31, 2012.
All interested parties who wish to purchase from this contract may do so by
following these simple procedures:
ORDERING INSTRUCTIONS
1. Contact the awarded manufacturer/dealer (see page 29) listed which you wish to purchase and
advise them of your interest to purchase from the Fire Rescue Vehicles & Other Fleet Equipment
Bid No. 11-10-1202. They will assist you with the placement of your order and answer any
questions you may have regarding the vehicles purchased through this program.
IMPORTANT NOTE: All agencies ordering any FORD, GENERAL MOTORS, or CHRYSLER
product, please be advised that you must use the appropriate FIN CODE/FAN CODE for the
Florida Sheriffs Association in order to obtain the manufacturer's concessions. Also, you must
TR 12430- Exhibit D
use your FIN CODE/FAN CODE as a secondary number. For further assistance call the Fleet
Customer Information Center for your appropriate manufacturer.
Manufacturer
Type Code
FSA Code
Fleet Center Contact
Numbers
FORD
FIN CODE
QE065
1-800-34-FLEET (1-800-343-5338)
GENERAL MOTORS
FAN CODE
917872
1-800-FLEET OP (1-800-353-3867)
CHRYSLER
FAN CODE
49313
1-800-999-FLEET (1-800-999-3533)
2. YOU MUST send
a copy of the
ORIGINAL PURCHASE ORDER (including
FSA's Contract No.
11-10-1202) you
submitted to
the participating manufacturer
to:
Florida Sheriffs Association
P. O. Box 12519
Tallahassee, Florida 32317-2519
ATTN: Lynn Meek, Cooperative Bid Coordinator
lmeek@flsheriffs.org
3. Basic information required on all purchase orders is listed on Page 31 of this Bid Award
Announcement. Purchase orders lacking the required basic information listed may result in
the delay of placement and/or confirmation of orders. NOTE: Purchasers are reminded that
the issuance of a Purchase Order does not in itself guarantee the placement of an order. The
agency is responsible for obtaining a "Confirmation of Order" from the respective manufacturer.
Manufacturers are required to complete a "Confirmation of Order" and send it to the purchaser
within fourteen (14) calendar days after receipt of purchase order. Purchasers are encouraged to
contact the dealer if a "Confirmation of Order" has not been received within a reasonable time
frame and request its issuance.
This program is designed to
provide participating agencies with the
most economically
priced fire
& rescue vehicles and other
fleet equipment tailored to their specific
needs, in a prompt
and timely
manner.
The Florida Fire Chiefs' Association, the Florida Sheriffs Association and the Florida Association of
Counties bid award for fire & rescue vehicles and other fleet equipment are as follows:
OVERVIEW of
AWARDED SPECIFICATIONS
Name of Manufacturer
Braun Industries, Inc.
ETR, L.L.C. (AEV)
Excellance, Inc.
Hall -Mark Fire Apparatus, Inc.
(Horton)
Pierce Manufacturing, Inc. (Medtec)
Type Vehicle
Base
Unit Price
Ford XLT F-350
$
1171,190.00
Ford XLT F-350
$
989029.00
Ford XLT F-350
$
1339038.00
Ford XLT F-350
$
127, 434.00
Ford XLT F-350
$
979,987.00
TR 12430- Exhibit D
Name of Manufacturer
Type Vehicle
SPECIFICATION # 01 - TYPE I AMBULANCE R x 2)
(cont'd)
Quality Emergency Vehicles Sales
Base
Unit Price
& Service, Inc. (Osage)
Ford XLT F-350
$
118, 775.00
Road Rescue Emergency Vehicles
Ford XLT F-350
$
105, 500.00
Stat-Line Industries (McCoy Miller)
Ford XLT F-350
$
95, 700.00
Wheeled Coach Industries, Inc.
Ford XLT F-350
$
102, 500.00
Braun Industries, Inc.
Ford XLT F-450
$
141, 778.00
ETR, L.L.C. (AEV)
Ford XLT F-450
$
115, 854.00
Excellance, Inc.
Ford XLT F-450
$
137, 506.00
Hall -Mark Fire Apparatus, Inc.
(Horton)
Ford XLT F-450
$
160, 515.00
Pierce Manufacturing, Inc. (Medtec)
Ford XLT F-450
$
1099,127.00
Quality Emergency Vehicles Sales
& Service, Inc. (Osage)
Ford XLT F-450
$
114, 775.00
Road Rescue Emergency Vehicles
Ford XLT F-450
$
132, 500.00
Stat-Line Industries (McCoy Miller)
Ford XLT F-350
$
113,000.00
Wheeled Coach Industries, Inc.
Ford XLT F-450
$
114, 368.00
ETR, L.L.C. (AEV)
Ford XLT F-
550
$
119, 593.00
Hall -Mark Fire Apparatus, Inc.
(Horton)
Ford XLT F-550
$
1629429.00
Pierce Manufacturing, Inc. (Medtec)
Ford XLT F-550
$
111, 665.00
Road Rescue Emergency Vehicles
Ford XLT F-550
$
135, 500.00
Wheeled Coach Industries, Inc.
Ford XLT F-550
$
1169259.00
ETR, L.L.C. (AEV)
Chevy Silverado 3 500
HD
$
989842.00
Excellance, Inc.
Chevy Silverado 3500
HD
$
123,936.00
Pierce Manufacturing, Inc. (Medtec)
Chevy Silverado 3500
HD
$
1049072.00
Road Rescue Emergency Vehicles
Chevy Silverado 3500
HD
$
125, 500.00
Stat-Line Industries (McCoy Miller)
Chevy Silverado 3500
HD
$
989892.00
Wheeled Coach Industries, Inc.
Chevy Silverado 3500
HD
$
101, 600.00
Braun Industries, Inc.
Dodge Ram
3500
$
123, 631.00
Road Rescue Emergency Vehicles
Dodge Ram
3500
$
102, 500.00
Stat-Line Industries (McCoy Miller)
Dodge Ram
3500
$
110, 504.00
Wheeled Coach Industries, Inc.
Dodge Ram
3500
$
103, 500.00
Braun Industries, Inc.
Dodge Ram
4500
$
144, 891.00
ETR, L.L.C. (AEV)
Dodge Ram
4500
$
117, 485.00
Excellance, Inc.
Dodge Ram
4500
$
142, 928.00
Hall -Mark Fire Apparatus, Inc.
(Horton)
Dodge Ram
4500
$
1629463.00
Pierce Manufacturing, Inc. (Medtec)
Dodge Ram
4500
$
112, 991.00
Quality Emergency Vehicles Sales
& Service, Inc. (Osage)
Dodge Ram
4500
$
122, 775.00
Road Rescue Emergency Vehicles
Dodge Ram
4500
$
132, 500.00
Stat-Line Industries (McCoy Miller)
Dodge Ram
4500
$
117, 530.00
Wheeled Coach Industries, Inc.
Dodge Ram
4500
$
1159000.00
TR 12430- Exhibit D
Name of Manufacturer
N # 01 -TYPE I
(cont'd)
ETR, L.L.C. (AEV)
Hall -Mark Fire Apparatus, Inc.
(Horton)
Pierce Manufacturing, Inc. (Medtec)
Road Rescue Emergency Vehicles
Wheeled Coach Industries, Inc.
TION # 02 - TYPE I
Braun Industries, Inc.
E IR, L.L.C. (AEV)
Hall -Mark Fire Apparatus, Inc.
(Horton)
Pierce Manufacturing, Inc. (Medtec)
Road Rescue Emergency Vehicles
Wheeled Coach Industries, Inc.
Braun Industries, Inc.
ETR, L.L.C. (AEV)
Excellance, Inc.
Hall -Mark Fire Apparatus, Inc.
(Horton)
Pierce Manufacturing, Inc. (Medtec)
Road Rescue Emergency Vehicles
Wheeled Coach Industries, Inc.
Braun Industries, Inc.
ETR, L.L.C. (AEV)
Excellance, Inc.
Hall -Mark Fire Apparatus, Inc.
(Horton)
Pierce Manufacturing, Inc. (Medtec)
Quality Emergency Vehicles Sales
& Service, Inc. (Osage)
Road Rescue Emergency Vehicles
Wheeled Coach Industries, Inc.
Braun Industries, Inc.
ETR, L.L.C. (AEV)
Excellance, Inc.
Hall -Mark Fire Apparatus, Inc.
(Horton)
Pierce Manufacturing, Inc. (Medtec)
Quality Emergency Vehicles Sales
& Service, Inc. (Osage)
Road Rescue Emergency Vehicles
Wheeled Coach Industries, Inc.
Type Vehicle
2
Dodge Ram 5500
Base
Unit Price
$ 1219083.00
Dodge Ram 5500
$
165, 885.00
Dodge Ram 5500
$
115,190.00
Dodge Ram 5500
$
1339900.00
Dodge Ram 5500
$
1169450.00
Ford
F-650
$
1749382.00
Ford
F-
650
$
1469448.00
Ford
F-650
$
194, 524.00
Ford
F-650
$
156, 641.00
Ford
F-650
$
158, 500.00
Ford
F-650
$
134, 500.00
Freightliner M2
$ 1829274.00
Freightliner M2
$ 1471,730.00
Freightliner M2
$ 1639440.00
Freightliner M2
$ 2029153.00
Freightliner M2
$ 156, 989.00
Freightliner M2
$ 166, 500.00
Freightliner M2
$ 139, 500.00
International TerraStar SFA
$
160, 026.00
International TerraStar SFA
$
132, 549.00
International TerraStar SFA
$
147, 066.00
International TerraStar SFA $ 1839094.00
International TerraStar SFA $ 145,997.00
International TerraStar SFA
$
139,355.00
International TerraStar SFA
$
148, 500.00
International TerraStar SFA
$
1289500.00
International
Durastar 4300M7
$
188, 352.00
International
Durastar 4300M7
$
149, 885.00
International
Durastar 4300M7
$
166,163.00
International
Durastar 4300M7
$
199, 992.00
International
Durastar 4300M7
$
163, 278.00
International
Durastar 4300M7
$
1579350.00
International
Durastar 4300M7
$
163, 500.00
International
Durastar 4300M7
$
148, 500.00
TR 12430- Exhibit D
Name of Manufacturer
#02 -
(cont'd)
Braun Industries, Inc.
ETR, L.L.C. (AEV)
Excellance, Inc.
Hall -Mark Fire Apparatus, Inc.
(Horton)
Pierce Manufacturing, Inc. (Medtec)
Quality Emergency Vehicles Sales
& Service, Inc. (Osage)
Road Rescue Emergency Vehicles
Wheeled Coach Industries, Inc.
Braun Industries, Inc.
ETR, L.L.C. (AEV)
Hall -Mark Fire Apparatus, Inc.
(Horton)
Pierce Manufacturing, Inc. (Medtec)
Quality Emergency Vehicles Sales
& Service, Inc. (Osage)
Road Rescue Emergency Vehicles
Wheeled Coach Industries, Inc.
Braun Industries, Inc.
ETR, L.L.C. (AEV)
Hall -Mark Fire Apparatus, Inc.
(Horton)
Road Rescue Emergency Vehicles
Wheeled Coach Industries, Inc.
Type Vehicle
2
Base
Unit Price
International
Durastar 430OLP
$
189, 086.00
International
Durastar 430OLP
$
158, 751.00
International
Durastar 430OLP
$
170, 091.00
International
Durastar 430OLP
$
201, 260.00
International
Durastar 430OLP
$
167, 828.00
International
Durastar 430OLP
$
160, 945.00
International
Durastar 430OLP
$
171, 500.00
International
Durastar 430OLP
$
152, 500.00
International
Durastar 440OLP
$
195, 902.00
International
Durastar 440OLP
$
159,934.00
International
Durastar 440OLP
$
202, 732.00
International
Durastar 440OLP
$
173, 284.00
International Durastar 440OLP
$
1669990.00
International Durastar 440OLP
$
172, 500.00
International Durastar 440OLP
$
158, 350.00
Spartan Metro Star RT
$
269, 628.00
Spartan Metro Star RT
$
236,464.00
Spartan
Metro
Star RT
$
2909375.00
Spartan
Metro
Star RT
$
245, 500.00
Spartan
Metro
Star RT
$
233, 320.00
SPECIFICATION # 03 - TYPE II AMBULANCE, VAN (4 x 2)
ETR, L. L. C. (AEV)
Ford E-350
$
55, 741.00
Pierce Manufacturing, Inc. (Medtec)
Ford E-350
$
539435.00
Quality Emergency Vehicles Sales
& Service, Inc. (Osage)
Ford E-350
$
649230.00
Road Rescue Emergency Vehicles
Ford E-350
$
599500.00
Stat-Line Industries (McCoy Miller)
Ford E-350
$
59,990.00
Wheeled Coach Industries, Inc.
Ford E-350
$
56, 532.00
ETR, L.L.C. (AEV)
Sprinter
$
72,571.00
Road Rescue Emergency Vehicles
Sprinter
$
78, 500.00
Stat-Line Industries (McCoy Miller)
Sprinter
$
82, 500.00
Wheeled Coach Industries, Inc.
Sprinter
$
76, 000.00
SPECIFICATION # 04 - TYPE III AMBULANCE (4 x 2)
Braun Industries, Inc.
Ford XL E-350
$
979306.00
ETR, L.L.C. (AEV)
Ford XL E-350
$
859198.00
Excellance, Inc.
Ford XL E-350
$
108, 758.00
TR 12430- Exhibit D
Nance of Manufacturer
IFICATION # 04 -
(cont'd)
Hall -Mark Fire Apparatus, Inc.
(Horton)
Pierce Manufacturing, Inc. (Medtec)
Quality Emergency Vehicles Sales
& Service, Inc. (Osage)
Road Rescue Emergency Vehicles
Stat-Line Industries (McCoy Miller)
Wheeled Coach Industries, Inc.
Braun Industries, Inc.
ETR, L.L.C. (AEV)
Excellance, Inc.
Hall -Mark Fire Apparatus, Inc.
(Horton)
Pierce Manufacturing, Inc. (Medtec)
Quality Emergency Vehicles Sales
& Service, Inc. (Osage)
Road Rescue Emergency Vehicles
Stat-Line Industries (McCoy Miller)
Wheeled Coach Industries, Inc.
Braun Industries, Inc.
ETR, L.L.C. (AEV)
Excellance, Inc.
Hall -Mark Fire Apparatus, Inc.
(Horton)
Pierce Manufacturing, Inc. (Medtec)
Quality Emergency Vehicles Sales
& Service, Inc. (Osage)
Road Rescue Emergency Vehicles
Stat-Line Industries (McCoy Miller)
Wheeled Coach Industries, Inc.
Braun Industries, Inc.
ETR, L.L.C. (AEV)
Excellance, Inc.
Hall -Mark Fire Apparatus, Inc.
(Horton)
Pierce Manufacturing, Inc. (Medtec)
Quality Emergency Vehicles Sales
& Service, Inc. (Osage)
Road Rescue Emergency Vehicles
Stat-Line Industries (McCoy Miller)
Wheeled Coach Industries, Inc.
ETR, L.L.C. (AEV)
Excellance, Inc.
Hall -Mark Fire Apparatus, Inc.
(Horton)
Type Vehicle
Base
Unit Price
Ford XL E-
3 50
$
122 9 409.00
Ford XL E-350
$
86,104.00
Ford XL E-350
$
91,275.00
Ford XL E-350
$
98, 500.00
Ford XL E-350
$
911,217.00
Ford XL E-3
50
$
999200.00
Ford XL E-450
$
119, 856.00
Ford XL E-450
$
98, 882.00
Ford XL E-450
$
113, 006.00
Ford XL E-450
$
146, 784.00
Ford XL E-450
$
959850.00
Ford XL E-450
$
1121,675.00
Ford XL E-450
$
112, 500.00
Ford XI. E-450
$
103, 556.00
Ford XL E-450
$
105, 000.00
Chevy G3500 $ 113, 572.00
Chevy G3500 $ 98, 672.00
Chevy G3500 $ 1219382.00
Chevy G3500 $ 130, 520.00
Chevy G3500 $ 98, 716.00
Chevy G3500
$
991,215.00
Chevy G3500
$
104, 500.00
Chevy G3500
$
1021,415.00
Chevy G3500
$
1069000.00
Chevy G4500 $ 140, 531.00
Chevy G4500 $ 1129365.00
Chevy G4500 $ 124, 339.00
Chevy G4500 $ 156,194.00
Chevy G4500 $ 108,156.00
Chevy G4500
$
120, 775.00
Chevy G4500
$
1219500.00
Chevy G4500
$
109, 634.00
Chevy G4500
$
1119400.00
GMC G3500
$
989672.00
GMC G3500
$
121, 382.00
GMC G3500 $ 130, 520.00
TR 12430- Exhibit D
Name of Manufacturer
(cont'd)
Pierce Manufacturing, Inc. (Medtec)
Quality Emergency Vehicles Sales
& Service, Inc. (Osage)
Road Rescue Emergency Vehicles
ETR, L.L.C. (AEV)
Excellance, Inc.
Hall -Mark Fire Apparatus, Inc.
(Horton)
Pierce Manufacturing, Inc. (Medtec)
Quality Emergency Vehicles Sales
& Service, Inc. (Osage)
Road Rescue Emergency Vehicles
ETR, L.L.C. (AEV)
Quality Emergency Vehicles Sales
& Service, Inc. (Osage)
TION # 05 — 75'
Type Vehicle
4x
Base
Unit Price
GMC
G3500
$
98, 716.00
GMC
G3500
$
999,215.00
GMC
G3500
$
104, 500.00
GMC
G4500
$
112, 365.00
GMC
G4500
$ -
124, 339.00
GMC
G4500
$
156 9194. 00
GMC
G4500
$
1089,156.00
GMC
G4500
$
120, 775.00
GMC
G4500
$
121, 500.00
Sprinter
$
979607.00
Sprinter
FORMED STAINLESS STEEL BODY
Aluminum Ladder:
Sutphen Corporation
EXTRUDED ALUMINUM BODY
Aluminum Ladder:
Hall -Mark Fire Apparatus, Inc.
(E-ONE)
Steel Ladder:
Crimson Fire, LLC (Public Safety
Solutions Group)
Ferrara Fire Apparatus, Inc.
Ferrara Fire Apparatus, Inc.
Rosenbauer South Dakota, LLC
IFI
— 75'
FORMED ALUMINUM BODY
Aluminum Ladder:
Pierce Manufacturing, Inc.
Steel Ladder:
Sutphen SL75
$ 112, 925.00
$ 650, 727.00
E-ONE HP 75 $ 519, 797.00
Crimson 75RMA $ 565, 033.00
Igniter XD $ 551, 566.00
Intruder $ 499, 648.00
Spartan Metro Star 75' $ 510,188.00
MOUNTED AERIAL APPARATUS —
Pierce Impel 75' HDL $ 5551,691.00
American LaFrance, LLC American LaFrance 75RML $ 581, 901.00
TR 12430- Exhibit D
Name of Manufacturer
Type Vehicle
SPECIFICATION # 06 - 75' REAR MOUNTED AERIAL APPARATUS -
FORMED ALUMINUM BODY
(cont'd)
Steel Ladder:
Crimson Fire, LLC (Public Safety
Solutions Group)
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
Pierce Manufacturing, Inc.
Rosenbauer South Dakota, LLC
Crimson 75RMA
KME Predator AerialCat FL0675
Pierce Impel 75' HDL
Spartan Metro Star 75'
SPECIFICATION # 06 - 75RFAR MOUNTED AERIAL APPARATUS -
FORMED STAINLESS STEEL BODY
Steel Ladder:
American LaFrance, LLC
Crimson Fire, LLC (Public Safety
Solutions Group)
American LaFrance 75RML
Crimson 75RMA
SPECIFICATION # 07 - 100' MID MOUNTED AERIAL APPARATUS -
EXTRUDED ALUMINUM BODY
Steel Ladder:
Base
Unit Price
$ 546, 291.00
$
587, 390.00
$
555,141.00
$
499, 929.00
$ 584,987.00
$ 5729135.00
Ferrara Fire Apparatus, Inc.
Igniter XD
$
755, 677.00
Ferrara Fire Apparatus, Inc..
Spectr
$
733,191.00
SPECIFICATION # 07 - 100' MID
MOUNTED AERIAL APPARATUS -
FORMED ALUMINUM BODY
Steel Ladder:
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
KME Predator AerialCat FL07100
$
800, 204.00
Pierce Manufacturing, Inc.
Pierce Arrow XT HDL
$
7539201.00
SPECIFICATION # 07 - 100' MID MOUNTED AERIAL APPARATUS -
FORMED STAINLESS STEEL BODY
Aluminum Ladder:
Sutphen Corporation
Sutphen SL 100
$ 744, 560.00
SPECIFICATION # 08 - 100' REAR MOUNTED AERIAL APPARATUS -
EXTRUDED ALUMINUM BODY
Aluminum Ladder:
Hall -Mark Fire Apparatus, Inc.
(E-ONE) E-ONE HP 100L $ 6939366.00
TR 12430- Exhibit D
Name of Manufacturer
Type Vehicle
Base
Unit Price
SPECIFICATION # 08 - 100' REAR MOUNTED AERIAL APPARATUS -
EXTRUDED ALUMINUM BODY
(cont'd)
Steel Ladder:
Crimson Fire, LLC (Public Safety
Solutions Group)
Ferrara Fire Apparatus, Inc.
Ferrara Fire Apparatus, Inc.
Rosenbauer South Dakota, LLC
Crimson 100RMA $
Igniter XD $
Spectr $
Spartan Gladiator 100' $
SPECIFICATION # 08 - 100' REAR MOUNTED AERIAL APPARATUS -
FORMED ALUMINUM BODY
Aluminum Ladder:
Pierce Manufacturing, Inc. Pierce Arrow XT HDL $
Steel Ladder:
American LaFrance, LLC
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
Pierce Manufacturing, Inc.
Rosenbauer South Dakota, LLC
KME Predator AerialCat FL08103
Pierce Arrow XT HDL
Spartan Gladiator 100'
674, 072.00
662, 036.00
631, 376.00
652, 394.00
665, 648.00
$
7509442.00
$
667 9180.00
$
653, 206.00
$
620, 852.00
SPECIFICATION # 08 — 100' REAR MOUNTED AERIAL APPARATUS —
FORMED STAINLESS STEEL BODY
Aluminum Ladder:
Pierce Manufacturing, Inc. Pierce Arrow XT HAL-SS $
Steel Ladder:
American LaFrance, LLC
Crimson Fire, LLC (Public Safety
Solutions Group)
American LaFrance 100RMA
/1i01
SPECIFICATION # 09 — MID MOUNTED AERIAL PLATFORM —
EXTRUDED ALUMINUM BODY
Aluminum Ladder:
Hall -Mark Fire Apparatus, Inc.
(E-ONE)
Steel Ladder:
Crimson Fire, LLC (Public Safety
Solutions Group)
Ferrara Fire Apparatus, Inc.
Ferrara Fire Apparatus, Inc.
Rosenbauer South Dakota, LLC
E-ONE HP 95 MM
673, 564.00
$ 753,942.00
$ 677,950.00
$ 849, 613.00
Crimson MM 100' $ 854, 583.00
Igniter XD $ 868,463.00
Spectr $ 8449351.00
Spartan Gladiator $ 798, 554.00
TR 12430- Exhibit D
Name of Manufacturer
Type Vehicle
SPECIFICATION #09 - MID MOUNTED AERIAL PLATFORM -
FORMED ALUMINUM BODY
Steel Ladder:
American LaFrance, LLC
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
Pierce Manufacturing, Inc.
Rosenbauer South Dakota, LLC
American LaFrance 100MMP
Base
Unit Price
$ 886, 602.00
KME Predator AerialCat FL09100 $ 8309497.00
Pierce Arrow XT Mid Mount $ 894, 531.00
Spartan Gladiator $ 780, 512.00
SPECIFICATION # 09 - MID MOUNTED AERIAL PLATFORM -
FORMED STAINLESS STEEL BODY
Aluminum Ladder:
Sutphen Corporation
Sutphen Corporation
Steel Ladder:
American LaFrance, LLC
Crimson Fire, LLC (Public Safety
Solutions Group)
SPH 100
SP110
American LaFrance 100MMP
Crimson MM 1009
SPECIFICATION # 10 - REAR MOMWED AERIAL PLATFORM -
EXTRUDED ALUMINUM BODY
Aluminum Ladder:
Hall -Mark Fire Apparatus, Inc.
(E-ONE)
Steel Ladder:
Crimson Fire, LLC (Public Safety
Solutions Group)
Ferrara Fire Apparatus, Inc.
Ferrara Fire Apparatus, Inc.
Rosenbauer South Dakota, LLC
E-ONE HP 100P
Crimson Star RM 1009
Igniter XD
Spectr
Spartan Gladiator
SPECIFICATION # 10 - REAR MOUNTED AERIAL PLATFORM -
FORMED ALUMINUM BODY
Aluminum Ladder:
Pierce Manufacturing, Inc.
Steel Ladder:
American LaFrance, LLC
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
Pierce Manufacturing, Inc.
Rosenbauer South Dakota, LLC
Pierce Arrow XT Rear Mount PAP
American LaFrance 10OR.MP
$ 969,128.00
$19,0149357.00
$ 891, 503.00
$ 858, 330.00
$ 8209298.00
$
7569389.00
$
7639430.00
$
729, 318.00
$
734, 810.00
$ 850, 581.00
$ 788, 974.00
KME Predator AerialCat FLO 10102 $ 791, 297.00
Pierce Arrow XT Rear Mount PAP $ 799 9 259.00
Spartan Gladiator $ 7101,125.00
TR 12430- Exhibit D
Name of Manufacturer
Type Vehicle
SPECIFICATION # 10 — REAR MOUNTED AERIAL PLATFORM —
FORMED STAINLESS STEEL BODY
Steel Ladder:
American LaFrance, LLC
Crimson Fire, LLC (Public Safety
Solutions Group)
American LaFrance 10ORMP
Crimson Star RM 100'
SPECIFICATION # 11 — MEDIUM DUTY RESCUE APPARATUS —
EXTRUDED ALUMINUM BODY RX2)
Freightliner M2-106:
Crimson Fire, LLC (Public Safety
Solutions Group)
Ferrara Fire Apparatus, Inc.
Hall -Mark Fire Apparatus, Inc.
(E-ONE)
Rosenbauer South Dakota, LLC
Wheeled Coach Industries, Inc.
International Durastar:
Crimson Fire, LLC (Public Safety
Solutions Group)
Ferrara Fire Apparatus, Inc.
Hall -Mark Fire Apparatus, Inc.
(E-ONE)
Rosenbauer South Dakota, LLC
Wheeled Coach Industries, Inc.
Base
Unit Price
$ 792, 399.00
$ 7609631.00
Crimson Star MR
$
158, 867.00
FFA 108 MDR Rescue
$
163, 914.00
E-ONE REHN
$
155, 999.00
FSA Rescue 11
$
178, 200.00
Rescue Force FLS 11 FTLNR
$
157, 500.00
Crimson Star MR
$
162, 549.00
FFA 108 MDR Rescue
$
1629379.00
E-ONE REHN
$
160, 899.00
FSA Rescue 11
$
179, 018.00
Rescue Force FLS 11 INTL
$
167, 500.00
SPECIFICATION # 11 — MEDIUM DUTY RESCUE APPARATUS —
FORMED ALUMINUM BODY RX2)
Freightliner M2-106:
American LaFrance, LLC
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
Pierce Manufacturing, Inc.
Rosenbauer South Dakota, LLC
Toyne, Inc. (Southeastern
Apparatus Sales, LLC)
International Durastar:
American LaFrance, LLC
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
Pierce Manufacturing, Inc.
Rosenbauer South Dakota, LLC
Sutphen Corporation
Toyne, Inc. (Southeastern
Apparatus Sales, LLC)
American LaFrance 16' W/AR $ 170, 316.00
KME FL 11 MDR $ 169, 404.00
Pierce MDR $ 165, 411.00
FSA Rescue 11 $ 1541,442.00
Toyne Medium Rescue $ 1989600.00
American LaFrance 16' W/AR $ 176, 390.00
KME FL 11 MDR $ 165, 607.00
Pierce MDR $ 174, 065.00
FSA Rescue 11 $ 155, 259.00
Sutphen CR Series Rescue $ 2589980.00
Toyne Medium Rescue $ 204,300.00
TR 12430- Exhibit D
Name of Manufacturer
Type Vehicle
SPECIFICATION # 12 - HEAVY RESCUE APPARATUS
Extruded Aluminum Body:
Crimson Fire, LLC (Public Safety
Solutions Group)
Ferrara Fire Apparatus, Inc.
Ferrara Fire Apparatus, Inc.
Hall -Mark Fire Apparatus, Inc.
(E-ONE)
Rosenbauer South Dakota, LLC
Formed Aluminum Body:
American LaFrance, LLC
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
Pierce Manufacturing, Inc.
Rosenbauer South Dakota, LLC
Sutphen Corporation
Toyne, Inc. (Southeastern
Apparatus Sales, LLC)
Crimson Star HR
Igniter XD XMFD
Intruder MFDXL
E-ONE REHN Typhoon
Spartan Force
American LaFrance 18' W/ACR
KME Predator FL 12HDR
Pierce Saber HDR
Spartan Force
Sutphen R Series
Spartan Heavy Rescue
SPECIFICATION # 13 - 2500 GALLON MOBILE WATER SUPPLY
FIRE APPARATUS - EXTRUDED ALUMINUM BODY (2_ Door
Freightliner M2-106:
Crimson Fire, LLC (Public Safety
Solutions Group)
Ferrara Fire Apparatus, Inc.
Hall -Mark Fire Apparatus, Inc.
(E-ONE)
International Workstar:
Crimson Fire, LLC (Public Safety
Solutions Group)
Ferrara Fire Apparatus, Inc.
Hall -Mark Fire Apparatus, Inc.
(E-ONE)
Base
Unit Price
$
237, 303.00
$
2719243.00
$
235, 984.00
$
2449925.00
$
247, 658.00
$ 273,887.00
$
267, 534.00
$
272, 561.00
$
229, 727.00
$
3559247.00
$ 2749000.00
Crimson Star Tanker $ 212, 368.00
FFA T2500 Tanker $ 249,330.00
E-ONE TTSA $ 207, 330.00
Crimson Star Tanker $ 211, 764.00
FFA T2500 Tanker $ 2479484.00
E-ONE TTSA $ 210,127.00
SPECIFICATION # 13 - 2500 GALLON MOBILE WATER SUPPLY
FIRE APPARATUS - FORMED ALUMINUM BODY (2 Doom
Freightliner M2-106:
American LaFrance, LLC
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
Pierce Manufacturing, Inc.
Rosenbauer South Dakota, LLC
Toyne, Inc. (Southeastern
Apparatus Sales, LLC)
American LaFrance T/A Tanker $ 255,828.00
KME Flatback FL132500 $ 236,125.00
Pierce Contender Series $ 206,391.00
FSA Tanker 13 $ 203, 365.00
Toyne FFCSA-2500 $ 233, 500.00
TR 12430- Exhibit D
Name of Manufacturer
Type Vehicle
SPECIFICATION # 13 - 2500 GALLON MOBILE WATER SUPPLY
FIRE APPARATUS - FORMED ALUMINUM BODY (2 Doom
(cont'd)
International Workstar:
American LaFrance, LLC
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
Pierce Manufacturing, Inc.
Rosenbauer South Dakota, LLC
Toyne, Inc. (Southeastern
Apparatus Sales, LLC)
Base
Unit Price
American LaFrance T/A Tanker $ 2809281.00
KME Flatback FL132500 $ 231, 803.00
Pierce Contender Series $ 211, 598.00
FSA Tanker 13 $ 2079103.00
Toyne FFCSA-2500
SPECIFICATION # 13 - 2500 GALLON MOBILE WATER SUPPLY
FIRE APPARATUS - FORMED GALVANNEAL STEEL BODY (2 Door)
Freightliner M2-106:
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
International Workstar:
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
KME Flatback FL132500
KME Flatback FL132500
SPECIFICATION # 13 - 2500 GALLON MOBILE WATER SUPPLY
FIRE APPARATUS - FORMED STAINLESS STEEL BODY (2 Doom
Freightliner M2-106:
Crimson Fire, LLC (Public Safety
Solutions Group)
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
Toyne, Inc. (Southeastern
Apparatus Sales, LLC)
International Workstar:
Crimson Fire, LLC (Public Safety
Solutions Group)
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
Sutphen Corporation
Toyne, Inc. (Southeastern
Apparatus Sales, LLC)
Crimson Star Tanker
KME Flatback FL132500
Toyne FFCSA-2500
Crimson Star Tanker
KME Flatback FL132500
Sutphen CTS-2500 Tanker
Toyne FFCSA-2500
SPECIFICATION # 14 - WILDLAND FIRE APPARATUS (4x4l
Ford F-550:
$ 2371,250.00
$ 227, 000.00
$ 222, 681.00
$ 2179103.00
$ 243, 952.00
$ 2409200.00
$ 214,970.00
$ 239, 636.00
$ 283, 629.00
$ 246, 500.00
American LaFrance, LLC Wildland Brush $ 85,970.00
Ferrara Fire Apparatus, Inc. Wildland Brush $ 99,060.00
TR 12430- Exhibit D
Name of Manufacturer
Type Vehicle
SPECIFICATION # 14 - WILDLAND FIRE APPARATUS (4x4�
(cont'd)
Ford F-550:
Hall -Mark Fire Apparatus, Inc.
(E-ONE)
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
Pierce Manufacturing, Inc.
Toyne, Inc. (Southeastern
Apparatus Sales, LLC)
Dodge Ram 5500:
American LaFrance, LLC
Ferrara Fire Apparatus, Inc.
Hall -Mark Fire Apparatus, Inc.
(E-ONE)
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
International Durastar 430OM7:
American LaFrance, LLC
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
Toyne, Inc. (Southeastern
Apparatus Sales, LLC)
Base
Unit Price
Wildland $ 849586.00
KME Wildland FL 14WFA $ 100, 597.00
Pierce F550 Wildland $ 889067.00
Wildland Brush $ 939300.00
Wildland Brush
$
899020.00
Wildland Brush
$
1029589.00
Wildland
$
859661.00
KME Wildland FL 14WFA
Wildland Brush
KME Wildland FL 14WFA
Wildland Brush
SPECIFICATION # 15 - COMMERCIAL PUMPER -
EXTRUDED ALUMINUM BODY (2 Doom
Freightliner M2:
Crimson Fire, LLC (Public Safety
Solutions Group)
Ferrara Fire Apparatus, Inc.
Hall -Mark Fire Apparatus, Inc.
(E-ONE)
Rosenbauer South Dakota, LLC
International Durastar:
Crimson Fire, LLC (Public Safety
Solutions Group)
Ferrara Fire Apparatus, Inc.
Hall -Mark Fire Apparatus, Inc.
(E-ONE)
Rosenbauer South Dakota, LLC
Sutphen Corporation
$ 100, 071.00
$ 95,594.00
$ 1319480.00
$ 134, 700.00
Crimson Star Pumper $ 1989057.00
FFA RP751 Pumper $ 208, 373.00
E-ONE TDPM $ 170, 517.00
FSA Pumper 13 $ 208, 768.00
Crimson Star Pumper $ 197, 690.00
FFA RP751 Pumper $ 206, 838.00
E-ONE TDPM $ 1769125.00
FSA Pumper 13 $ 210, 876.00
Sutphen C 1 Pumper $ 216, 792.00
TR 12430- Exhibit D
Name of Manufacturer
Type Vehicle
SPECIFICATION # 15 - COMMERCIAL PUMPER -
FORMED ALUMINUM BODY (2 Doorl
Freightliner M2:
American LaFrance, LLC
Crimson Fire, LLC (Public Safety
Solutions Group)
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
Pierce Manufacturing, Inc.
Rosenbauer South Dakota, LLC
Toyne, Inc. (Southeastern
Apparatus Sales, LLC)
International Durastar:
American LaFrance, LLC
Crimson Fire, LLC (Public Safety
Solutions Group)
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
Pierce Manufacturing, Inc.
Rosenbauer South Dakota, LLC
Toyne, Inc. (Southeastern
Apparatus Sales, LLC)
Base
Unit Price
American LaFrance S/M Pumper $ 2129670.00
Crimson Star Pumper $ 1889773.00
KME Challenger FL 15COML $ 199, 783.00
Pierce Contender Series $ 1799598.00
FSA Pumper 13 $ 182, 408.00
Toyne FFCSA Pumper $ 208, 000.00
American LaFrance S/M Pumper
Crimson Star Pumper
KME Challenger FL15COML
Pierce Contender Series
FSA Pumper 13
Toyne FFCSA Pumper
SPECIFICATION # 15 - COMMERCIAL PUMPER -
FORMED GALVANNEAL STEEL BODY (2 Doom
Freightliner M2:
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
International Durastar:
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
KME Challenger FL 15COML
KME Challenger FL15COML
SPECIFICATION # 15 - COMMERCIAL PUMPER -
FORMED STAINLESS STEEL BODY (2 Doorl
Freightliner M2:
American LaFrance, LLC
Crimson Fire, LLC (Public Safety
Solutions Group)
Hall -Mark Fire Apparatus, Inc.
(E-ONE)
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
Toyne, Inc. (Southeastern
Apparatus Sales, LLC)
American LaFrance S/M Pumper
Crimson Star Pumper
E-ONE PSTS
KME Challenger FL15COML
Toyne FFCSA Pumper
$ 222, 246.00
$
188,817.00
$
197, 654.00
$
184, 671.00
$
184,516.00
$ 213, 500.00
$ 1959172.00
$ 192, 712.00
$ 213, 763.00
$ 2009801.00
$ 199,325.00
$ 204, 530.00
$ 212, 000.00
TR 12430- Exhibit D
Name of Manufacturer
Type Vehicle
SPECIFICATION # 15 — COMMERCIAL PUMPER —
FORMED STAINLESS STEEL BODY (2 Door)
(cont'd)
International Durastar:
American LaFrance, LLC
Crimson Fire, LLC (Public Safety
Solutions Group)
Hall -Mark Fire Apparatus, Inc.
(E-ONE)
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
Toyne, Inc. (Southeastern
Apparatus Sales, LLC)
)N # 16 —
Extruded Aluminum Body:
Hall -Mark Fire Apparatus, Inc.
(E-ONE)
Sutphen Corporation
Formed Aluminum Body:
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
Pierce Manufacturing, Inc.
Sutphen Corporation
Formed Galvanneal Steel Body:
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
Pierce Manufacturing, Inc.
Formed Stainless Steel Body:
Hall -Mark Fire Apparatus, Inc.
(E-ONE)
Kovatch Mobile Equip. Corp..
(KME Fire Apparatus)
Pierce Manufacturing, Inc.
TION # 16 —
Extruded Aluminum Body:
Crimson Fire, LLC (Public Safety
Solutions Group)
Rosenbauer South Dakota, LLC
Formed Aluminum Body:
Crimson Fire, LLC (Public Safety
Solutions Group)
American LaFrance S/M Pumper
Crimson Star Pumper
E-ONE PSIS
KME Challenger FL15COML
Toyne FFCSA Pumper
L I CUSTOM
Base
Unit Price
$ 2239902.00
$ 202, 899.00
$ 205,237.00
$ 202, 043.00
$ 217, 500.00
11
E-ONE 1"Yphoon Pumper $ 2679508.00
S-Series Custom $ 308, 970.00
KME Challenger FL 16LVL 1 $ 273, 541.00
Pierce Saber Series $ 269, 266.00
S-Series Custom $ 290, 993.00
KME Challenger FL 16LVL 1 $ 268, 943.00
Pierce Velocity SLT Series $ 337, 573.00
E-ONE Typhoon Pumper $ 271, 734.00
KME Challenger FL 16LVL 1 $ 278, 274.00
Pierce Impel SS Series $ 308, 890.00
I CUSTOM PUMPER - SPARTAN CHASSIS
Crimson Metro Star Pumper L 1 $ 269, 507.00
Spartan Force 16 $ 272,842.00
Crimson Metro Star Pumper L1
$ 260, 656.00
TR 12430- Exhibit D
Name of Manufacturer
SPECIFICATION # 16 -
(cont'd)
Formed Aluminum Body:
Rosenbauer South Dakota, LLC
Toyne, Inc. (Southeastern
Apparatus Sales, LLC)
Formed Stainless Steel Body:
Crimson Fire, LLC (Public Safety
Solutions Group)
Toyne, Inc. (Southeastern
Apparatus Sales, LLC)
[CATION # 16 -
Extruded Aluminum Body:
Ferrara Fire Apparatus, Inc.
Formed Aluminum Body:
Toyne, Inc. (Southeastern
Apparatus Sales, LLC)
Formed Stainless Steel Body:
Toyne, Inc. (Southeastern
Apparatus Sales, LLC)
LION # 16 —
Type Vehicle
Base
Unit Price
L I CUSTOM PUMPER - SPARTAN CHASSIS
Spartan Force 16 $ 2489128.00
AMERICAN LAFR.ANCE CHASSIS
Formed Aluminum Body:
American LaFrance, LLC
Formed Stainless Steel Body:
American LaFrance, LLC
1 # 17 —
Extruded Aluminum Body:
Ferrara Fire Apparatus, Inc.
Hall -Mark Fire Apparatus, Inc.
(E-ONE)
Rosenbauer South Dakota, LLC
Sutphen Corporation
Formed Aluminum Body:
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
Toyne Spartan Metro Star FFCSA $ 286, 000.00
Crimson Metro Star Pumper L1 $ 272,159.00
Toyne Spartan Metro Star FFCSA $ 290, 250.00
JSTOM PUMPER - HME CHASSIS
Intruder $ 277,618.00
Toyne 1871 W FFCSA $ 293, 500.00
Toyne 1871W FFCSA $ 297,500.00
JSTOM PUMPER -
American LaFrance Custom
S/M Pumper $ 300t634.00
American LaFrance Custom
S/M Pumper $ 301,992.00
:L II CUSTOM PUMPER - CUSTOM CHASSIS
Igniter XD LFD $ 399, 874.00
E-ONE Cyclone Pumper $ 373,084.00
Commander FSA 17 $ 3649916.00
Monarch Series Custom $ 4219112.00
KME Flatback FL17LVL2 $ 3579181.00
TR 12430- Exhibit D
Name of Manufacturer
17—
(cont'd)
Formed Aluminum Body:
Pierce Manufacturing, Inc.
Rosenbauer South Dakota, LLC
Formed Galvanneal Steel Body:
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
Pierce Manufacturing, Inc.
Formed Stainless Steel Body:
Hall -Mark Fire Apparatus, Inc.
(E-ONE)
Kovatch Mobile Equip. Corp.
(KME Fire Apparatus)
Pierce Manufacturing, Inc.
TI
fAn
Type Vehicle
EL II C
Extruded Aluminum Body:
Crimson Fire, LLC (Public Safety
Solutions Group)
Rosenbauer South Dakota, LLC
Formed Aluminum Body:
Crimson Fire, LLC (Public Safety
Solutions Group)
Rosenbauer South Dakota, LLC
Toyne, Inc. (Southeastern
Apparatus Sales, LLC)
Formed Stainless Steel Body:
Crimson Fire, LLC (Public Safety
Solutions Group)
Toyne, Inc. (Southeastern
Apparatus Sales, LLC)
TION #
Extruded Aluminum Body:
Ferrara Fire Apparatus, Inc.
Formed Aluminum Body:
Toyne, Inc. (Southeastern
Apparatus Sales, LLC)
Formed Stainless Steel Body:
Toyne, Inc. (Southeastern
Apparatus Sales, LLC)
Unit Price
Pierce Arrow XT Series $ 387, 678.00
Commander FSA 17 $ 3409030.00
KME Flatback FL17LVL2 $ 3529,582.00
Pierce Quantum Series $ 395,482.00
E-ONE Cyclone Pumper
$ 3949151.00
KME Flatback FL 17LVL2 $ 361, 913.00
Pierce Velocity Series $ 3999974.00
USTOM PUMPER - SPARTAN CEM SSIS
Crimson Metro Star Pumper L2 $ 366, 042.00
Spartan Gladiator 17 $ 373, 656.00
Crimson Metro Star Pumper L2 $ 341, 025.00
Spartan Gladiator 17 $ 346, 660.00
Toyne Spartan Gladiator $ 377,000.00
Crimson Metro Star Pumper L2 $ 3689450.00
Toyne Spartan Gladiator $ 381, 000.00
II CUSTOM
Spectr LFD
Toyne Spectr
Toyne Spectr
$ 3869017.00
$ 3799000.00
$ 383,000.00
TR 12430- Exhibit D
Name of Manufacturer
Type Vehicle
SPECIFICATION # 17 - LEVEL II CUSTOM PUMPER -
AMERICAN LAFRANCE CHASSIS
Formed Aluminum Body:
American LaFrance, LLC
Formed Stainless Steel Body:
American LaFrance, LLC
American LaFrance Custom
Base
Unit Price
Rescue Pumper $ 354, 804.00
American LaFrance Custom
Rescue Pumper $ 3569162.00
TR 12430- Exhibit D
MANUFACTURERS/DEALERS
American LaFrance LLC
1090 Newton Way
Summerville, SC 29483-7430
Contact: Kevin Hyde
Phone: 843-486-7510
Cell: 843-789-9809
Fax: 843-486-7580
Email: kevinhyde@americanlafrance.com
Braun Industries, Inc.
1170 Production Drive
Van Wert, OH 45891
Contact: Penny Richardson
Phone: 419-232-7020
Cell:
Fax: 419-232-7070
Email: pennyr@braunambulances.com
Crimson Fire, Inc.
(public Safety Solutions Group)
2525 Clarcona Road
Apopka, FL 32 703
Contact: James Schwaller
Phone: 407-798-0004
Cell: 352-427-6605
Fax: 407-798-0013
Email: j schwaller@epofc. com
ETR, L.L.C.
(AEV - American Emergency Vehicles)
920 Britt Court, Suite #252
Altamonte Springs, FL 32701
Contact: Jerry Michaluk
Phone: 407-339-6737
Cell: 407-701-0700
Fax: 407-339-8198
Email: jerry@etrllc.org
Excellance, Inc.
453 Lanier Road
Madison, AL 35758
Contact: Thomas R. Pugh
Phone: 800-882-9799
Cell: 256-468-6007
Fax: 256-772-8792
Email: tommy@excellance.com
Ferrara Fire Apparatus, Inc.
27855 James Chapel Road
Holden, LA 70744
Contact: Dave Carlton
Phone: 800-443-9006
Cell: 225-202-3287
Fax: 225-567-7680
Email: davec@ferrarafire.com
Hall -Mark Fire Apparatus
"NE & Horton)
3431 N.W. 27th Ave.
Ocala, FL 34475
Contact: Ed Martin
Phone: 352-629-6305
Cell: 352-266-4422
Fax: 352-629-3471
Email: emartin@hall-markfire.com
Kovatch Mobile Equipment Corp.
(KME Fire Apparatus)
1 Industrial Complex
Nesquehoning, PA 18240
Contact: Philip Gerace
Phone: 570-669-5174
Cell: 570-233-1452
Fax: 570-669-5124
Email: pgerace@kovatch.com
Pierce Manufacturing, Inc.
(Ten-8 Fire Equipment, Inc.)
2904 59th Ave. Drive East
Bradenton, FL 34208
Contact: Mark Jones
Phone: 800-228-8368
Cell: 941-704-6244
Fax. 941-756-7779
Email: mjones@ten8fire.com
Quality Emergency Vehicles
Sales & Service, Inc.
123 N. Orchard Street, Suite 1-B
Ormond Beach, FL 32174
Contact: Fred Allegretti
Phone*386-254-4911
Cell: 386-547-8089
Fax: 386-254-4933
Email: ambulancesales@aol.com
TR 12430- Exhibit D
AWARDED MANUFACTURERS/DEALERS
(continued)
Road Rescue Emergency Vehicles
(The Phoenix Group)
1323 Shelter Rock Road
Orlando, FL 32835
Contact: Gary Goetsch
Phone: 321-217-3201
Cell: 321-217-3201
Fax: 407-532-1880
Email: hotbirrdll@aol.com
Rosenbauer South Dakota, LLC
(EVS Firefighting ighting Technologies)
4661 Johnson Road, Suite 1
Coconut Creek, FL 33073
Contact: Robert Windesheim
Paul Stephenson
Phone: 954-428-5201
Cell: 954-734-3549
Fax. 954-428-5202
Email: rwindesheftn@ 1evs.com
pstephenson@evsfire.com
Stat-Line Industries
(McCoy Miller)
2050 Haines Street
Jacksonville, FL 32206
Contact: Allan Assaf
Phone: 904-356-6543
Cell: 904-343-2822
Fax: 904-356-0841
Email: mail@stat-line.com
Sutphen
Corporation
10140 Bellavista Circle Unit 1104
Miromar Lakes, FL 33913
Contact:
David Stonitsch
Phone:
239-267-5300
Cell:
239-357-8530
Fax:
239-590-9246
Email:
dstonitsch@hotmail.com
Toyne, Inc.
(Southeastern Apparatus Sales, LLQ
106 Corte Del Rosa
Venice, FL 34285
Contact: John Lovell
Phone: 256-362-9280
Cell: 205-541-1980
Fax: 256-362-9280
Email: john@seapparatus.com
mr-apparatus@yahoo.com
Wheeled Coach Industries, Inc.
2737 N. Forsyth Road
Winter Park, FL 32792
Contact: Art Sprague
Phone: 407-677-7777 x369
Cell: 407-718-1240
Fax: 800-513-8174
Email: art.sprague@wheeledcoach.com
TR 12430- Exhibit D
BASIC INFORMATION
REQUIRED
ON A VEHICLE PURCHASE ORDER
When filling out a purchase order for a vehicle that is to be purchased under the Florida Fire Chiefs'
Association, Florida Sheriffs Association & Florida Association of Counties Bid No. 11-10-1202, there
are certain items of information that must be on the purchase order, or enclosed with the purchase
order, so as to minimize the possibility of errors on the order.
This information includes, but is not limited to, the following:
• Date of order
• Purchase order number
• Originator of purchase order
• Name and number (phone & fax) of contact person responsible for receiving "Confirmation
of Order" and scheduling of delivery
• Delivery date required
• Contract number (11-10-1202)
• Contract specification number of vehicle(s), number of vehicles ordered and base price of
vehicles
• Type vehicle ordered (i.e. Type I Ambulance, Ford XLT F-450, 4x4)
• FIN CODE for the Florida Sheriffs Association (QE065) and your agency's FIN CODE when
ordering FORD products
• FAN CODE for the Florida Sheriffs Association (917872) and your agency's FAN CODE
when ordering GENERAL MOTORS products
• FAN CODE for the Florida Sheriffs Association (49313) and your agency's FAN CODE when
ordering CHRYSLER products
Inclusion of the above mentioned items will help prevent possible misunderstanding of the order
and will assist in any audit of the purchase orders, or vehicles, that may be deemed necessary in the
future.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION OF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
Base Specifications
SPECIFICATION #01 - TYPE I AMBULANCE
2 WHEEL DRIVE
(DUAL REAR WHEEL, CAB &CHASSIS)
ALL ITEMS FACTORY INSTALLED UNLESS OTHERWISE INDICATED
FORD, GENERAL MOTORS, DODGE OR APPROVED EQUIVALENT
1. ENGINE
a. Turbo diesel engine, minimum 5.9L displacement.
b. Must include the chassis manufacturer's "AMBULANCE PREP PACKAGE".
C. Heavy-duty alternator, minimum 200 amp.
d. Maintenance free heavy-duty batteries, 750 CCA minimum.
e. Manufacturer's heavy-duty engine cooling.
2. TRANSMISSION
a. Automatic transmission, 4 speed minimum with overdrive.
b. Manufacturer's heavy-duty cooling.
3. AXLES
a. Manufacturer's standard drive axle ratio for ambulance prep.
4. PERFORMANCE ITEMS
a. Power steering
b. Anti -lock brakes
C. Power brakes, disc type front, disc or drum rear.
d. Fuel capacity, 250 miles minimum without refueling
e. Heavy-duty front and rear shocks.
f. Front stabilizer bar.
TR 12430- Exhibit D
Base Specifications #OI - Type I Ambulance
5. COMFORT ITEMS
a. Factory installed air conditioning
b. Tinted glass (factory tint)
C. Minimum seating for two
d. Rubber floor mat instead of carpeting
e. AM/FM radio
f. Power door locks
g. Power windows
h. Speed control and tilt wheel.
6. SAFETY ITEMS
a. Driver and passenger lap and shoulder belt with retractor.
b. Driver and passenger air bags
C. Dual electric horns
d. Outside mirrors to provide vision for vehicles 96" wide.
e. Two speed wipers with intermittent.
f. Interior dome lights wired to right and left doors.
7. TIRES AND WHEELS
a. BSW, all season tread radial 16 inch tires.
b. Conventional spare tire and wheel
C. Jack and wheel wrench
8. CHASSIS, FRAME, CAB
a. Minimum GVWR 11,400 lbs.
b. Cab and chassis only
C. Cab to center of axle 84 inches
9. MODULAR BODY CONSTRUCTION
a. The ambulance body and patient compartment shall be sufficient in size to meet the
requirements of this specification and those of paragraph 3.10.1 of the current KKK-A-1822F.
TR 12430- Exhibit D
FLORIDA.
ASSOCIATION OF
COUNTIES
All About Florida,
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 FORD XLT F-350
Specification #Ol
(Type I Ambulance, 4s2)
The Ford XLT F-350, Type I Ambulance purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded
by manufacturer by specification.
BASE PRICE. $117,190.00
MANUFACTURER: Braun Industries, Inc.
BASE PRICE: $133,038.00
MANUFACTURER: Excellance, Inc.
BASE PRICE: $979987.00
MANUFACTURER: Pierce Manufacturing, Inc. (Medtec)
BASE PRICE: $105, 500.00
MANUFACTURER: Road Rescue Emergency Vehicles
BASE PRICE: ' $1021,500.00
MANUFACTURER: Wheeled Coach Industries, Inc.
$98,029.00
ETR, L.L.C. (AEV)
$1279434.00
Hall -Mark Fire Apparatus (Horton)
$1189775.00
Quality Emergency Vehicles (Osage)
$95,700,00
Stat-Line Industries (McCoy Miller)
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet KKK-A-1822F, or the most current revision for Type I Ambulance. Since
equipment needs and preferences are going to vary from agency to agency - any additional
options required or changes to the base unit desired by the purchaser shall be made through
the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORASSOCIATHANIDA
OF
COUNTIES
IES
All About 141oreda
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 FORD XLT F-450
Specification #O1
(Type I Ambulance, 4g2)
The Ford X.T F-450, Type I Ambulance purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded
by manufacturer by specification.
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
Purchasers
$1419778.00
Braun Industries, Inc.
$1379506.00
Excellance, Inc.
$1091,127.00
Pierce Manufacturing, Inc. (Medtec)
$1329500.00
Road Rescue Emergency Vehicles
$1149368.00
Wheeled Coach Industries, Inc.
$1159,854.00
ETR, L.L.C. (AEV )
$1601,515.00
Hall -Mark Fire Apparatus (Horton)
$1149775.00
Quality Emergency Vehicles (Osage)
$1131,000.00
Stat-Line Industries (McCoy Miller)
are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs'
Association,
of Counties have identified and equipped the
items required tc
equipment need:
options required
the manufactures
meet KKK-A-1822F, or the r.
and preferences are going
or changes to the base unit
listed.
Florida Sheriffs Association and Florida Association
base unit with those specifications and equipment
zost current revision for Type I Ambulance. Since
to vary from agency to agency - any additional
desired by the purchaser shall be made through
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
As,,sT)qx rR.).,,N1, Z
COUNTIES
AU About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 FORD XLT F-550
Specification #0 1
(Type I Ambulance, 4g2)
The Ford XLT F-550, 'Type I Ambulance purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSKs base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded
by manufacturer by specification.
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
$1191,593.00
ETR, L.L.C. (AEV)
$1119665.00
Pierce Manufacturing, Inc. (Medtec)
$1.169259.00
Wheeled Coach Industries, Inc.
$1629429.00
Hall -Mark Fire Apparatus (Horton)
$1351,500.00
Road Rescue Emergency Vehicles
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet KKK-A-1822F, or the most current revision for Type I Ambulance. Since
equipment needs and preferences are going to vary from agency to agency - any additional
options required or changes to the base unit desired by the purchaser shall be made through
the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
4�� t'q YryL�(/yt��}y�R�y�Iy/D `Aye^`
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8r FLORIDA ASSOCIATION OF COUNTIES
2012 CHEVY SILVERADO 3500 HD
Specification #01
(Type I Ambulance, 4g2)
The Chevy Silverado 3500 HD, Type I Ambulance purchased through this contract comes with all
the standard equipment as specified by the manufacturer for this model and FSKs base vehicle
specification(s) requirements which are included and made a part of this contract's vehicle base
price as awarded by manufacturer by specification.
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
$981,842.00
ETR, L.L.C. (AEV)
$1041,072.00
Pierce Manufacturing, Inc. (Medtec)
$98, 892.00
Stat-Line Industries (McCoy Miller)
$1.239,936, 00
Excellance, Inc.
$1259500.00
Road Rescue Emergency Vehicles
$1019600.00
Wheeled Coach
Industries, Inc.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet KKK-A-1822F, or the most current revision for Type I Ambulance. Since
equipment needs and preferences are going to vary from agency to agency - any additional
options required or changes to the base unit desired by the purchaser shall be made through
the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FEOR.IDA
ASSOCLATIONOF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 DODGE RAM 3500
Specification #Ol
(Type I Ambulance, 4s2)
The Dodge Ram 3500, Type I Ambulance purchased through this contract comes with all the
standard equipment as specified by the manufacturer for this model and FSA's base vehicle
specification(s) requirements which are included and made a part of this contract's vehicle base
price as awarded by manufacturer by specification.
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
$1239631.00
Braun Industries, Inc.
$1109504.00
Stat-Line Industries (McCoy Miller)
$1029500.00
Road Rescue Emergency Vehicles
$1039 500.00
Wheeled Coach Industries, Inc.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet KKK-A-1822F, or the most current revision for Type I Ambulance. Since
equipment needs and preferences are going to vary from agency to agency - any additional
options required or changes to the base unit desired by the purchaser shall be made through
the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOc:I T O OF
COUNTIES
All About 141orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 DODGE RAM 4500
Specification #0 1
(Type I Ambulance, 4x2)
The Dodge Ram 4500, Type I Ambulance purchased through this contract comes with all the
standard equipment as specified by the manufacturer for this model and FSA's base vehicle
specifications) requirements which are included and made a part of this contract's vehicle base
price as awarded by manufacturer by specification.
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
$1449891.00
Braun Industries, Inc.
$1429928.00
Excellance, Inc.
$1121,991.00
Pierce Manufacturing, Inc. (Medtec)
$132, 500.00
Road Rescue Emergency Vehicles
$115,000.00
Wheeled Coach Industries, Inc.
$1171,485.00
ETR, L.L.C. (AEV)
$1629463.00
Hall -Mark Fire Apparatus (Horton)
$122,775.00
Quality Emergency Vehicles (Osage)
$1179,530.00
Stat-Line Industries (McCoy Miller)
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet KKK-A-1822F, or the most current revision for Type I Ambulance. Since
equipment needs and preferences are going to vary from agency to agency - any additional
options required or changes to the base unit desired by the purchaser shall be made through
the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
F I,ORIDA►.
ASSOCIATION OF
COUNTIES
.All About 141oreda
FLORIDA FIRE CHI,EFS9 ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 DODGE RAM 5500
Specification #01
(Type I Ambulance, 4a2)
The Dodge Ram 5500, Type I Ambulance purchased through this contract comes with all the
standard equipment as specified by the manufacturer for this model and FSA's base vehicle
specification(s) requirements which are included and made a part of this contract's vehicle base
price as awarded by manufacturer by specification.
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
$1211,083.00
ETR, L.L.C. (AEA
$1159190.00
Pierce Manufacturing, Inc. (Medtec)
$1169450.00
Wheeled Coach Industries, Inc.
$1659,885.00
Hall -Mark Fire Apparatus (Horton)
$1339900.00
Road Rescue Emergency Vehicles
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet KKK-A-1822F, or the most current revision for Type I Ambulance. Since
equipment needs and preferences are going to vary from agency to agency - any additional
options required or changes to the base unit desired by the purchaser shall be made through
the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOUKRUN, OF
COITNTIES
All About 141orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
Base Specifications
SPECIFICATION
#02 -
TYPE I
AMBULANCE
2 WHEEL
DRIVE
MEDIUM
DUTY
(DUAL REAR WHEEL, CAB &CHASSIS)
ALL ITEMS FACTORY INSTALLED UNLESS OTHERWISE INDICATED
FORD, FREIGHTLINER, INTERNATIONAL OR APPROVED EQUIVALENT
1. ENGINE
a. Diesel engine, 6 cylinder minimum.
b. Heavy-duty alternator, minimum 250 amp.
C. Maintenance free heavy-duty batteries, 750 CCA minimum.
d. Manufacturer's heavy-duty engine cooling.
2. TRANSMISSION
a. Electronic Allison Transmission
b. Manufacturer's transmission oil cooler: water to oil heavy-duty cooling.
3. AXLES
a. Front Axle: 7,000 lbs.
b. Rear Axle: 12,000 lbs.
C. Front Suspension: 7,000 lbs.
d. Rear Suspension: 12,000 lbs. air suspension with dual instant
response leveling valves.
4. PERFORMANCE ITEMS
a. Power Steering
b. Anti -lock brakes
C. Power brakes, disc type front, disc or drum rear.
d. Fuel capacity, 250 miles minimum without refueling
e. Heavy-duty front and rear shocks.
TR 12430- Exhibit D
Base Specifications #02 - Type I Ambulance Medium Duty
5. COMFORT ITEMS
a. Factory installed air conditioning
b. Tinted glass (factory tint)
c. Dual air suspension seats with armrest
d. Rubber floor mat instead of carpeting
e. AM/FM radio
6. SAFETY ITEMS
a. Driver and passenger lap and shoulder belt with retractor.
b. Dual electric horns
C. Outside mirrors to provide vision for vehicles 96" Wide
d. Two speed Wipers with intermittent
e. Interior dome lights wired to right and left doors.
f. Halogen headlights With daytime running feature.
7. TIRES AND WHEELS
a. BSW, all season tread radial 19.5 inch tires
8. CHASSIS, FRAME, CAB
a. Minimum GVWR 16,500 lbs.
b. Cab to center of axle 100 inches minimum
9. MODULAR BODY CONSTRUCTION
a. The ambulance body and patient compartment shall be sufficient in size to meet the
requirements of this specification and those of paragraph 3.10.1 of the current KKK-A-1822F.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION OF
CUUNTIES
All About blorida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 FORD F-650
Specification #02
(Type I Ambulance, 4g2 Medium Duty)
The Ford F-650, 'Type I Medium Duty Ambulance purchased through this contract comes with all
the standard equipment as specified by the manufacturer for this model and FSA's base vehicle
specification(s) requirements which are included and made a part of this contract's vehicle base
price as awarded by manufacturer by specification.
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
$1 ?4, 382.00
Braun Industries, Inc.
$194,524.00
Hall -Mark Fire Apparatus (Horton)
$1589500.00
Road Rescue Emergency vehicles
$146,448.00
ETR, L.L.C. (AEV)
$156, 641.00
Pierce Manufacturing, Inc. (Medtec)
$1349500.00
Wheeled Coach Industries, Inc.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet KKK-A-1822F, or the most current revision for Type I Ambulance. Since
equipment needs and preferences are going to vary from agency to agency - any additional
options required or changes to the base unit desired by the purchaser shall be made through
the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate .vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION OF
COUNTIES
AU About 11orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 FREIGHTLINER M2
Specification #02
(Type I Ambulance, 4g2 Medium Duty)
The Freightliner M2, 'lope I Medium Duty Ambulance purchased through this contract comes
with all the standard equipment as specified by the manufacturer for this model and FSA's base
vehicle specification(s) requirements which are included and made a part of this contract's vehicle
base price as awarded by manufacturer by specification.
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER.
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
$1821,274.00
Braun Industries, Inc.
$1631,440.00
Excellance, Inc.
$1569989.00
Pierce Manufacturing, Inc. (Medtec)
$1399500.00
Wheeled Coach Industries, Inc.
$1471,730.00
E'TR, L.L.C. (AEV)
$2029153.00
Hall -Mark Fire Apparatus (Horton)
$1669500.00
Road Rescue Emergency Vehicles
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet KKK-A-1822F, or the most current revision for Type I Ambulance. Since
equipment needs and preferences are going to vary from agency to agency - any additional
options required or changes to the base unit desired by the purchaser shall be made through
the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATI(MN OF
COUNTIES
All About 141orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 INTERNATIONAL TERRASTAR SFA
Specification #02
(Type I Ambulance, 4z2 Medium Duty)
The International Terrastar SFA, Type I Medium Duty Ambulance purchased through this contract
comes with all the standard equipment as specified by the manufacturer for this model and FSNs
base vehicle specification(s) requirements which are included and made a part of this contract's
vehicle base price as awarded by manufacturer by specification.
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
$1609,026.00
Braun Industries, Inc.
$1471,066.00
Excellance, Inc.
$1451,997.00
Pierce Manufacturing, Inc. (Medtec)
$1481,500.00
Road Rescue Emergency Vehicles
$1329549.00
ETR, L.L.C. (AEV)
$1839094.00
Hall -Mark Fire Apparatus (Horton)
$1399355.00
Quality Emergency Vehicles (Osage)
$128, 500.00
Wheeled Coach Industries, Inc.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet KKK-A-1822F, or the most current revision for Type I Ambulance. Since
equipment needs and preferences are going to vary from agency to agency - any additional
options required or changes to the base unit desired by the purchaser shall be made through
the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION OF
COUNTIES
AU About ,Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 INTERNATIONAL DURA3TAR 4300M7
Specification #02
(Type I Ambulance, 4g2 Medium Duty)
The International Durastar 4300M7, Type I Medium Duty Ambulance purchased through this
contract comes with all the standard equipment as specified by the manufacturer for this model
and FSA's base vehicle specification(s) requirements which are included and made a part of this
contract's vehicle base price as awarded by manufacturer by specification.
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
$1889352.00
Braun Industries, Inc.
$1669163.00
Excellance, Inc.
$1639278.00
Pierce Manufacturing, Inc. (Medtec)
$1639500.00
Road Rescue Emergency Vehicles
$1499885.00
ETR, L.L.C. (AEV)
$1999992.00
Hall -Mark Fire Apparatus (Horton)
$1579350.00
Quality Emergency Vehicles (Osage)
$1489500.00
Wheeled Coach Industries, Inc.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet KKK-A-1822F, or the most current revision for Type I Ambulance. Since
equipment needs and preferences are going to vary from agency to agency - any additional
options required or changes to the base unit desired by the purchaser shall be made through
the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATIONOF
COUNTIES
AU About blorida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 INTERNATIONAL DURASTAR 430OLP
Specification #02
(Type I Ambulance, 4z2 Medium Duty)
The International Durastar 4300LP, Type I Medium Duty Ambulance purchased through this
contract comes with all the standard equipment as specified by the manufacturer for this model
and FSA's base vehicle specification(s) requirements which are included and made a part of this
contract's vehicle base price as awarded by manufacturer by specification.
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
$1891,086.00
Braun Industries, Inc.
$1701,091.00
Excellance, Inc.
$1679828.00
Pierce Manufacturing, Inc. (Medtec)
$1719500.00
Road Rescue Emergency Vehicles
$1589751.00
ETR, L.L.C. (AEV)
$2019260.00
Hall -Mark Fire Apparatus (Horton)
$1609945.00
Quality Emergency Vehicles (Osage)
$1529500.00
Wheeled Coach Industries, Inc.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet KKK-A-1822F, or the most current revision for Type I Ambulance. Since
equipment needs and preferences are going to vary from agency to agency - any additional
options required or changes to the base unit desired by the purchaser shall be made through
the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCLA.TION OF
COUNTIES
All About 141mida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 INTERNATIONAL DURASTAR 4400LP
Specification #02
(Type I Ambulance, 4g2 Medium Duty)
The International Durastar 4400LP, Type I Medium Duty Ambulance purchased through this
contract comes with all the standard equipment as specified by the manufacturer for this model
and FSA's base vehicle specification(s) requirements which are included and made a part of this
contract's vehicle base price as awarded by manufacturer by specification.
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER. -
BASE PRICE:
MANUFACTURER:
$1959902.00
Braun Industries, Inc.
$2021,732.00
Hall -Mark Fire Apparatus (Horton)
$1661,990.00
Quality Emergency Vehicles (Osage)
$1589350.00
Wheeled Coach Industries, Inc.
$1591,934.00
ETR, L.L.C. (AEV)
$1739284.00
Pierce Manufacturing, Inc. (Medtec)
$1729500.00
Road Rescue Emergency Vehicles
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet IUKK-A-1822F, or the most current revision for Type I Ambulance. Since
equipment needs and preferences are going to vary from agency to agency - any additional
options required or changes to the base unit desired by the purchaser shall be made through
the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
Assocuvt"ioN. Z) `
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 SPARTAN METRO STAR RT
Specification #02
(Type I Ambulance, 4z2 Medium Duty)
The Spartan Metro Star RT, Type I Medium Duty
comes with all the standard equipment as specified
base vehicle specification(s) requirements which ar+
vehicle base price as awarded by manufacturer by
BASE PRICE:
MANUFACTURER:
BASE PRICE:
N'[ANUFACTURER:
BASE PRICE:
MANUFACTURER:
$2691,628.00
Braun Industries, Inc.
Ambulance purchased through this contract
by the manufacturer for this model and FSA's
included and made a Dart of this contract's
specification.
$2901,375.00
Hall -Mark Fire Apparatus (Horton)
$2331,320.00
Wheeled Coach Industries, Inc.
$2369464,00
ETR, L.L.C. (AEV)
$245 9 500.00
Road Rescue
Emergency Vehicles
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet KKK-A-1822F, or the most current revision for 1`ype I Ambulance. Since
equipment needs and preferences are going to vary from agency to agency - any additional
options required or changes to the base unit desired by the purchaser shall be made through
the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION OF
COUNTIES
All About blorida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
Base Specifications
SPECIFICATION #03 - TYPE II AMBULANCE
2 WHEEL DRIVE -VAN
ALL ITEMS FACTORY INSTALLED UNLESS OTHERWISE INDICATED
FORD, SPRINTER, OR APPROVED EQUIVALENT
1. ENGINE
a. Diesel or gas engine, must meet KKK requirements.
b. Must include the chassis manufacturer's "AMBULANCE
PREP PACKAGE".
C. Heavy-duty alternator, minimum 200 amp.
d. Maintenance free heavy-duty batteries, 750 CCA minimum.
e. Manufacturer's heavy-duty engine cooling.
2, TRANSMISSION
a. Automatic transmission, 4 speed with overdrive.
b. Manufacturer's heavy-duty cooling.
3. AXLES
a. Manufacturer's standard drive axle ratio for ambulance prep.
4. PERFORMANCE ITEMS
a. Power steering
b. Anti -lock brakes
C. Power brakes, disc type front, disc or drum rear.
d. Fuel capacity, minimum 25 gallon
e. Heavy-duty front and rear shocks.
f. Front stabilizer bar.
TR 12430- Exhibit D
Base Specifications #03 - Type H Ambulance Van
5. COMFORT ITEMS
a. Factory installed air conditioning
b. Tinted glass (factory tint)
C. Dual captains chairs with armrest
d. Rubber floor mat instead of carpeting
e. AM/FM radio
f. Power door locks
g. Power windows
h. Speed control and tilt wheel.
6. SAFETY ITEMS
a. Driver and passenger lap and shoulder belt with retractor.
b. Driver and passenger air bags
C. Dual electric horns
d. Two speed wipers with intermittent
e. Interior dome lights wired to right and left doors.
7. TIRES AND WHEELS
a. BSW, all season tread radial 15 inch tires
b. Conventional spare tire and wheel
C. Jack and wheel wrench
8. CHASSIS, FRAME, CAB
a. Minimum GVWR 8,550 lbs.
b. 138" wheelbase
9. CONSTRUCTION
a. The ambulance patient compartment shall be sufficient in size to meet the requirements of
this specification and those of paragraph 3.10.1 of the current KKK-A-1822F.
TR 12430- Exhibit D
FLORIDASSOCIATION A
COUNTIES
AU About 11orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 FORD E-350
Specification #03
(Type II Ambulance, 4g2 Van)
The Ford E-350, Type II Ambulance Van purchased through this contract comes
standard equipment as specified by the manufacturer for this model and FSKs
specification(s) requirements which are included and made a part of this contract's
price as awarded by manufacturer by specification.
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
$55,?41.00
ETR, L.L.C. (AEV)
$64,230.00
Quality Emergency Vehicles (Osage)
$59, 990.00
Stat-Line Industries (McCoy Miller)
with all the
base vehicle
vehicle base
$539435,00
Pierce Manufacturing, Inc. (Medtec)
$59,500.00
Road Rescue Emergency Vehicles
$569532.00
Wheeled Coach
Industries, Inc.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet KKK-A-1822F, or the most current revision for Type II Ambulance. Since
equipment needs and preferences are going to vary from agency to agency - any additional
options required or changes to the base unit desired by the purchaser shall be made through
the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATIONOF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 SPRINTER
Specification #03
(Type II Ambulance, 4g2 Van)
The Sprinter, Type II Ambulance Van purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded
by manufacturer by specification.
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
$729571.00
ETR, L.L.C. (AEV)
$829500.00
Stat-Line Industries (McCoy Miller)
$789 500.00
Road Rescue Emergency Vehicles
$76,000.00
Wheeled Coach Industries, Inc.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet KKK-A-1822F, or the most current revision for Type II .Ambulance. Since
equipment needs and preferences are going to vary from agency to agency - any additional
options required or changes to the base unit desired by the purchaser shall be made through
the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION Of
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
Base Specifications
SPECIFICATION #04 -TYPE III AMBULANCE
2 WHEEL DRIVE
(DUAL REAR WHEEL, CAB &CHASSIS)
ALL ITEMS FACTORY INSTALLED UNLESS OTHERWISE INDICATED
FORD, GENERAL MOTORS, SPRINTER OR APPROVED EQUIVALENT
1. ENGINE
a. Diesel or gas engine, must meet KKK requirements.
b. Must include the chassis manufacturer's "AMBULANCE PREP PACKAGE".
C. Heavy-duty alternator, minimum 200 amp.
d. Maintenance free heavy-duty batteries, 750 CCA minimum.
e. Manufacturer's heavy-duty engine cooling.
2. TRANSMISSION
a. Automatic transmission, 4 speed with overdrive.
b. Manufacturer's heavy-duty cooling.
3. AXLES
a. Manufacturer's standard drive axle ratio for ambulance prep.
4. PERFORMANCE ITEMS
a. Power steering
b. Anti -lock brakes
C. Power brakes, disc type front, disc or drum rear.
d. Fuel capacity, 250 miles minimum without refueling
e. Heavy-duty front and rear shocks.
f. Front stabilizer bar.
TR 12430- Exhibit D
Base Specifications #04 - Type III Ambulance
5. COMFORT ITEMS
a. Factory installed air conditioning
b. Tinted glass (factory tint)
C. Minimum seating for two
d. Rubber floor mat instead of carpeting
e. AM/FM radio
f. Power door locks
g. Power windows
h. Speed control and tilt wheel.
6. SAFETY ITEMS
a. Driver and passenger lap and shoulder belt with retractor.
b. Driver and passenger air bags.
C. Dual electric horns
d. Outside mirrors to provide vision for vehicles 96" wide.
e. Two speed wipers with intermittent.
f. Interior dome lights wired to right and left doors.
7. TIRES AND WHEELS
a. BSW, all season tread radial 16" tires.
b. Conventional spare tire and wheel
C. Jack and wheel wrench
8. CHASSIS, FRAME, CAB
a. Minimum GVWR 10,500 lbs.
b. Cab/chassis cutaway
c. Wheel base 138" minimum
9. MODULAR BODY CONSTRUCTION
a. The ambulance body and patient compartment shall be sufficient in size to meet the
requirements of this specification and those of paragraph 3.10.1 of the current KKK-A-1822F.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION OF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 FORD XI. U350
Specification #04
(Type III Ambulance, 4s2)
The Ford XL E-350, Type III Ambulance purchased through this contract comes with all the
standard equipment as specified by the manufacturer for this model and FSA's base vehicle
specification(s) requirements which are included and made a part of this contract's vehicle base
price as awarded by manufacturer by specification.
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
$979306.00
Braun Industries, Inc.
$1089758,00
Excellance, Inc.
$86,104.00
Pierce Manufacturing, Inc. (Medtec)
$981,500.00
Road Rescue Emergency Vehicles
$991,200.00
Wheeled Coach Industries, Inc.
$85,198.00
FIR, L.L.C. (AEV)
$1229409.00
Hall -Mark Fire Apparatus (Horton)
$91,275.00
Quality Emergency Vehicles (Osage)
$91,217.00
Stat-Line Industries (McCoy Miller)
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet KKK-A-1822F, or the most current revision for Type III' Ambulance.
Since equipment needs and preferences are going to vary from agency to agency - any additional
options required or changes to the base unit desired by the purchaser shall be made through
the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCTATIONOF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 FORD XL E-450
Specification #04
(Type III Ambulance, 4g2)
The Ford XL E-450, Type III Ambulance purchased through this contract comes with all the
standard equipment as specified by the manufacturer for this model and FSA's base vehicle
specification(s) requirements which are included and made a part of this contract's vehicle base
price as awarded by manufacturer by specification.
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BABE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
$1199856.00
Braun Industries, Inc.
$1131,006.00
Excellance, Inc.
$959850.00
Pierce Manufacturing, Inc. (Medtec)
$1121,500.00
Road Rescue Emergency Vehicles
$1059,000.00
Wheeled Coach Industries, Inc.
$989882,00
ETR, L.L.C. (AEV)
$1461,784.00
Hall -Mark Fire Apparatus (Horton)
$1129675.00
Quality Emergency Vehicles (Osage)
$103, 556.00
Stat-Line Industries (McCoy Miller)
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet KKK-A-1822F, or the most current revision for Type III Ambulance. Since
equipment needs and preferences are going to vary from agency to agency - any additional
options required or changes to the base unit desired by the purchaser shall be made through
the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATIONNOF
COUNTIES
AU About :41orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 CHEVY G3500
Specification #04
(Type III Ambulance, 4g2)
The Chevy G3500, Type III Ambulance purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded
by manufacturer by specification.
BABE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
$1139572.00
Braun Industries, Inc.
$1219 382.00
Excellance, Inc.
$981,71 f .00
Pierce Manufacturing, Inc. (Medtec)
$1049500.00
Road Rescue Emergency Vehicles
$1069,000.00
Wheeled Coach
Industries, Inc.
$98,672.00
ETR, L.L.C. (AEV)
$1309520.00
Hall -Mark Fire Apparatus (Horton)
$99,215.00
Quality Emergency Vehicles (Osage)
$1.021,415.00
Stat-Line Industries (McCoy Miller)
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet KKK-A-1822F, or the most current revision for Type III Ambulance. Since
equipment needs and preferences are going to vary from agency to agency - any additional
options required or changes to the base unit desired by the purchaser shall be made through
the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
COUNTIES
All About 141orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 CHEVY G4500
Specification #04
(Type III Ambulance, 4x2)
The Chevy G4500, I)rpe III Ambulance purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSNs base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded
by manufacturer by specification.
EASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
$1401,531.00
Braun Industries, Inc.
$1249339.00
Excellance, Inc.
$1081,156.00
Pierce Manufacturing, Inc. (Medtec)
$1219500.00
Road Rescue Emergency Vehicles
$1119400.00
Wheeled Coach Industries, Inc.
$112, 365.00
ETR, L.L.C. (AEV)
$1569194.00
Hall -Mark Fire Apparatus � (Horton)
$1.209775,00
Quality Emergency Vehicles (Osage)
$1091,634.00
Stat-Line Industries (McCoy Miller)
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet KKK-A-1822F, or the most current revision for Type III Ambulance. Since
equipment needs to vary from agency to agency - any additional
options required desired by the purchaser shall be made through
the manufacturer
and preferences are going
or changes to the base unit
listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
F�Lyt ¢R.IDA`NOF
COUNTIES
All About Norida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 GMC G3500
Specification #04
(Type III Ambulance, 4g2)
The GMC G3500, 'I)rpe III Ambulance purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded
by manufacturer by specification.
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BABE PRICE:
MANUFACTURER:
$98, 672.00
ETR, L.L. C. (AEV)
$1301,520.00
Hall -Mark Fire Apparatus (Horton)
$999215.00
Quality Emergency Vehicles (Osage)
$1211,382.00
Excellance, Inc.
$98,716.00
Pierce Manufacturing, Inc. (Medtec)
$1049500.00
Road Rescue Emergency Vehicles
Purchasers are advised that the above referenced vehicle, specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet KKK-A-1822F, or the most current revision for Type III Ambulance. Since
equipment needs and preferences are going to vary from agency to agency - any additional
options required or changes to the base unit desired by the purchaser shall be made through
the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 GMC G4500
Specification #04
(Type III Ambulance, 4x2)
The GMC G4500, Type III Ambulance purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded
by manufacturer by specification.
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
BASE PRICE:
MANUFACTURER:
$1129365.00
ETR, L.L.C. (AEV)
$1569194.00
Hall -Mark Fire Apparatus (Horton)
$120,775.00
(duality Emergency Vehicles (Osage)
$1249339.00
Excellance, Inc.
$1089156.00
Pierce Manufacturing, Inc. (Medtec)
$1211,500.00
Road Rescue Emergency Vehicles
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet KKK-A-1822F, or the most current revision for Type III Ambulance. Since
equipment needs and preferences are going to vary from agency to agency - any additional
options required or changes to the base unit desired by the purchaser shall be made through
the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION` OF
COUNTIES
All About Rorida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 SPRINTER
Specification #04
(Type III Ambulance, 4g2)
The Sprinter, Type III Ambulance purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded
by manufacturer by specification.
BASE PRICE:
MANUFACTURER:
$979607.00
ETR, L.L. C. (AEV)
$1129925,00
Quality Emergency Vehicles (Osage)
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet KKK-A-1822F, or the most current revision for Type III Ambulance. Since
equipment needs and preferences are going to vary from agency to agency - any additional
options required or changes to the base unit desired by the purchaser shall be made through
the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCU'VY10INT OF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
Base Specifications
SPECIFICATION #05 - 75' NIID MOUNTED
Fil :4 z'"IrNg"4 ;j V41 Z74yo a 09
ALL ITEMS FACTORY INSTALLED UNLESS OTHERWISE INDICATED
THE CAB AND CHASSIS SHALL BE PROVIDED BY THE BODY MANUFACTURER
1. DOCUMENTATION, DELIVERY. TRAINING
a. When requested by end user, bidders to accurately state wheelbase, cab to axle, overall length,
bumper swing turn radius, curb -to -curb turning radius, overall height, overall width, GVWR,
angle of approach, angle of departure and SCAAN certification for drivetrain compatibility in
submitted specifications
b. Approval drawings provided prior to construction commencement
c. Two (2) sets of operator and service manuals
d. Delivery to be F.O.B. customer's location
e. Three (3) days of training by employee of manufacturer
f. Pump test certification by independent third party
g. Water tank capacity certification by independent third party
h. Aerial non-destructive, waterway flow test, performance and stability testing by independent
third party
i. 12 volt and, if applicable, 110 volt testing by independent third party
j . Vehicle weight, as measured by certified scales
2. CHASSIS
a. 110,000 psi heat treated steel frame rail with full length inner 110,000 psi C-channel liner
b. 10 gauge polished stainless steel 16" to 24" extended front bumper with aluminum diamond
plate gravel shield
C. Tow hooks or eyes front and rear attached to the frame
d. 22,500 pound minimum front axle, suspension, tubeless radial tires, steel disc wheels
e. 31, 000 pound minimum rear axle, suspension, tubeless radial tires, steel disc wheels
f. Front and rear mud flaps
g. NFPA 1901 Chapter 4.15.3 top speed rating requirement
TR 12430- Exhibit D
Base Specifications # 05 - 759 Mid Mounted Aerial Apparatus
h. S-cam air brakes or equivalent, as large as possible, with automatic slack adjusters
i. Manufacturer's standard compressor
j . Minimum 5000 cubic inch air reservoir capacity
k. Air dryer, color coded air lines, turn drain valves on reservoirs
1. ABS brakes
m. Power steering with tilt/telescopic wheel
n. Vehicle data recorder (VDR) in compliance with Chapter 4.11 with required software meeting
4.11.8
o. Electronic Stability Control shall be provided in compliance with NFPA 1901 Chapter 4.13.1.2
if the manufacturer cannot comply with Chapters 4.13.1.1 through 4.13.1.1.3.2.
p. Tire pressure monitoring system with Chapter 4.13.4
3. POWERTRAIN
a. Minimum 400 horsepower turbocharged diesel engine
b. Engine exhaust at front of right rear wheels
C. Secondary braking to meet NFPA
d. Engine manufacturer's statement of engine installation approval with approved cooling system
e. Drivelines to meet engine torque rating
f. Silicone coolant hoses with constant torque clamps
g. Automatic transmission
h. 50 gallon minimum fuel tank
i. OEM oil, fuel, transmission filters
4. CAB
a. Medium length tilt aluminum cab meeting NFPA 1901 Chapter 14.3.2
b. Seating for four, three in SCBA seats with SCBA brackets
C. Air ride driver seat, all others fixed position
d. All persons in 3-point seat belts per Chapter 14, seats equipped with seat belt/occupant
detection/warning system per Chapter 14
e. Electric over hydraulic cab tilt with manual back-up
f. Single tone cab paint finish with 10 year paint warranty pro -rated
g. Air conditioning and heating
h. Remote controlled mirrors (from driver's position) with separate flat and convex sections
i. DOT compliant headlights
j . Forward facing turn and warning lights
k. Cornering turn and warning lights
1. Minimum four (4) dome lights with red and clear bulbs
m. Minimum four (4) under cab step lights
n. Cab and compartment door ajar light and buzzer
o. One (1) engine compartment light
p. Color coded and function coded wiring
q. Alternator sized according to amp draw report
r. Minimum four (4) 750 CCA batteries
S. Load manager with automatic high idle function
t. Dual air horns with dual in -cab controls
5. AERIAL APPARATUS - ALUMINUM OR STEEL
a. Aerial shall meet or exceed all sections of NFPA 1901 Chapter 19
TR 12430- Exhibit D
Base Specifications # 05 - 75 " Mid Mounted Aerial Apparatus
b. Ladder material: aluminum or steel
C. Mid -mounted configuration
d. 4-section aerial with minimum elevation of 75' per NFPA requirements
e. Rated horizontal reach per NFPA requirements
f. Rungs shall meet all aspects of NFPA 1901 19.2.5
g. Rungs equipped with a slip resistant surface meeting NFPA 1901 19.2.5
h. Rungs spacing meeting NFPA 1901 19.2.5
i. Turntable with pedestal mounted controls meeting NFPA 1901 19.4
j . Aerial rated load capacity not flowing water: 500 lbs. minimum in addition to equipment
mounted at tip of ladder -
k. Aerial rated load capacity while flowing 1000 gpm: 500 lbs. minimum in addition to equipment
mounted at tip of ladder
1. Rated load capacities shall meet and /or exceed NFPA 1901 19.3
m. The aerial shall be rated in multiple configurations per Chapter 19.3.4
n. Extend/retract, rotate and hydraulic or electric over hydraulic controls meeting NFPA 1901
19.5 through 19.5.3.6.
o. Hydraulic pressure gauge at turntable controls
p. Illuminated Angle of Elevation Indicator meeting NFPA 1901 19.4.1
q. Flowmeter on pump panel meeting NFPA 1901 19.6.8
r. All aerial control devices shall meet NFPA 1901 19.17
S. Fall protection provisions shall be provided.
t. Bidders to state type of stabilizers and overall stabilizers spread
u. Aerial shall meet structural safety factors in accordance with NFPA 1901 19.20
V. Aerial shall meet NFPA 1901 stability safety factors Chapter 19.21
w. Lighted turntable area
X. The aerial manufacturer (the company that manufacturers the entire aerial -device) shall
maintain a Quality Control Program in accordance with NFPA 1901 Chapter 19.22
y. Special attention shall be paid to meeting all safety requirements per NFPA 1901 19.20
Z. Aerial shall be fully tested and certified by third party certified testing company per NFPA
1901 19.24 and 19.25
aa. 2-way intercom system between ladder tip and turntable control pedestal.
bb. Minimum 1000 gpm waterway system meeting NFPA 1901 with remote control nozzle (controls
at fly section and at turntable control pedestal) with movable manual pinned waterway or
remote control movable waterway.
cc. Maximum travel height 10 ft.
dd. Minimum 4" waterway discharge with 4" valve with handwheel or electric control on pump
panel
ee. Minimum 4" waterway inlet (non -gated) on rear or on side of body per NFPA 1901 Chapter
19.6.6
ff. Waterway relief valve and minimum 1.5" drain
gg. Stabilizer controls and stabilizer to aerial controls mounted on left side of apparatus body
at pump panel
hh. One (1) high intensity spotlights on ladder tip
n. Two high intensity flood lights on ladder base
jj . Painted finish on steel aerial -bidder shall provide copy of paint warranty on aerial
kk. Instruction plates and signs must be installed per NFPA 1901 Chapter 19.23
6. FIRE PUMP & PLUMBING
a. Minimum 1250 GPM pump as rated per NFPA 1901 Chapter 16
b. Air operated pump shift
TR 12430- Exhibit D
Base Specifications # 05 - 75 " Mid Mounted Aerial Apparatus
C. Discharge pressure relief valve
d. Intake pressure relief valve
e. Master drain valve
f. Electric dry type primer
g. Pump panel lights, 3 each side
h. Pump compartment light
i. OK to pump lights in cab and at pump panel
j . Engine cooler
k. Pump cooler
1. Two (2) 6" steamers, one on side panel
m. 2.5" left side gated suction
n. 1.5"' tank fill
o. Two (2) 2" crosslay hose beds over the pump compartment
p. Two (2) 2-1/2" left side discharges
q. Two (2) 2-1/2" right side discharges
r. Stainless steel schedule 10 piping with 10 year warranty
S. Panel gauge package: water tank level, tach, oil pressure, water temperature, voltmeter, light
and alarm system
t. Minimum 300 gallon polypropylene booster tank with lifetime warranty
u. 3" tank to pump connection
V. Minimum 10" x 8" fill tower with minimum 4" overflow tube
w. 15 ft. of soft suction hose sized for capacity of fire pump
7. APPARATUS BODY
a. Bidders to bid on each of their offered construction types:
• Extruded aluminum
• Formed aluminum
• Formed galvanneal steel
• Formed stainless steel
b. Bidders to state thicknesses, alloys and construction methods of all materials used in body
construction
C. High left side compartments
d. High right side compartments
e. Bidders to accurately state the total cubic footage of compartment space, along with each
compartment size
f. Lights in compartments to meet NPPA 1901 Chapter 13.10.5
g. Hose bed lighting must be provided per NFPA Chapter 1901 13.10.2
h. Back up alarm
i. Ladder storage for minimum 85' NFPA ground ladders, ladders to be included
j . Rear pike pole storage for minimum of six (6) pike poles fully enclosed at rear of apparatus
k. Slide out pump operator platform
1. Hose bed with hose restraints to be NFPA quint compliant
m. Steps and handrails for climbing from ground to turntable - bidders to state exact design
n. Lights at each step
o. Stop/turn/back up lights
p. DOT clearance and marker lights
q. License plate light
r. Rear deck lights
S. Rub rail along each side of body
t. Running boards at each pump panel
TR 12430- Exhibit D
Base Specifications #05 - 75" Mid Mounted Aerial Apparatus
u. Brushed stainless steel or black non -glare aluminum pump panels
8. EMERGENCY WARNING
a. NFPA Zone A lower and upper level lighting
b. NFPA Zone B / D lower level lighting
C. NFPA Zone C upper and lower level lighting
d. Electronic 200 watt siren/PA with minimum 100 watt speaker recessed in bumper
9. PAINT FINISH/REFLECTIVE STRIPING
a. Cab and body to be painted single tone with 10 year pro -rated paint and corrosion perforation
warranty
b. Wheels painted to match the cab and body
C. Reflective striping in accordance with Chapter 15.9.3
d. Reflective chevron on rear of apparatus in accordance with Chapter 15.9.3.2.
a. 1 year bumper to bumper mechanical, excluding normal wear and tear items
b. 10 year cab and body structural
C. 10 year paint pro -rated
d. 10 year corrosion perforation on cab and body
e. 20 year aerial structural
f. Lifetime frame warranty
g. 2 year front axle
h. 2 year rear axle
i. 5 year engine
j . 5 year fire pump
k. Lifetime booster tank
1. Manufacturer's standard 5 year warranty for transmission
TR 12430- Exhibit D
FLORIDA
ASSOCIATION OF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 75' NIID MOUNTED AERIAL APPARATUS
Specification #05
(Formed Stainless Steel Body - Aluminum Ladder)
The 75' Mid Mounted Aerial Apparatus, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL:
BASE PRICE:
MANUFACTURER:
Sutphen SL75
$6501,727.00
Sutphen Corporation
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a quint apparatus with a special emphasis on Chapters 1,
29 39 49 99 129 139 149 159 16, 18, 19, FMVSS (applicable areas) and NHTSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATIONOF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS", ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
Base Specifications
SPECIFICATION #06 - 75' REAR MOUNTED
Q �) V�l IZAA
ALL ITEMS FACTORY INSTALLED UNLESS OTHERWISE INDICATED
THE CAB AND CHASSIS SHALL BE PROVIDED BY THE BODY MANUFACTURER
1. DOCUMENTATION, DELIVERY, TRAINING
a. When requested by end user, bidders to accurately state wheelbase, cab to axle, overall
length, bumper swing turn radius, curb -to -curb turning radius, overall height, overall
width, GVWR, angle of approach, angle of departure and SCAAN certification for drivetrain
compatibility in submitted specifications
b. Approval drawings provided prior to construction commencement
c. Two (2) sets of operator and service manuals
d. Delivery to be F.O.B. customer's location
e. Three (3) days of training by employee of manufacturer
f. Pump test certification by independent third party
g. Water tank capacity certification by independent third party
h. Aerial non-destructive, waterway flow test, performance and stability testing by independent
third party
i. 12 volt and, if applicable, 110 volt testing by independent third party
j . Vehicle weight, as measured by certified scales
2. CHASSIS
a. 110,000 psi heat treated steel frame rail with full length inner 110,000 psi C-channel liner
b. 10 gauge polished stainless steel 169' to 24" extended front bumper with aluminum diamond
plate gravel shield
c. Tow hooks or eyes front and rear attached to the frame
d. 20,000 pound minimum front axle, suspension, tubeless radial tires, steel disc wheels
e. 31, 000 pound minimum rear axle, suspension, tubeless radial tires, steel disc wheels
f. Front and rear mud flaps
g. NFPA 1901 Chapter 4.15.3 top speed rating requirement
h. S-cam air brakes or equivalent, as large as possible, with automatic slack adjusters
TR 12430- Exhibit D
Base Specifications #06 - 75' Rear Mounted Aerial Apparatus
i. Manufacturer's standard compressor
j . Minimum 5000 cubic inch air reservoir capacity
k. Air dryer, color coded air lines, turn drain valves on reservoirs
1. ABS brakes
m. Power steering with tilt/telescopic wheel
n. Vehicle data recorder (VDR) in compliance with Chapter 4.11 with required software meeting
4.11.8
0. Electronic Stability Control shall be provided in compliance with NFPA 1901 Chapter
4.13.1.2 if the manufacturer cannot comply with Chapters 4.13.1.1 through 4.13.1.1.3.2.
p. Tire pressure monitoring system with Chapter 4.13.4
3. POWERTRAIN
a. Minimum 400 horsepower turbocharged diesel engine
b. Engine exhaust at front of right rear wheels
C. Secondary braking to meet NFPA
d. Engine manufacturer's statement of engine installation approval with approved cooling
system
e. Drivelines to meet engine torque rating
f. Silicone coolant hoses with constant torque clamps
g. Automatic transmission
h. 50 gallon minimum fuel tank
i. OEM oil, fuel, transmission filters
4. CAB
a. Medium length tilt aluminum cab meeting NFPA 1901 Chapter 14.3.2
b. Seating for four, three in SCBA seats with SCBA brackets
C. Air ride driver seat, all others fixed position
d. All persons in 3-point seat belts per Chapter 14, seats equipped with seat belt/occupant
detection/warning system per Chapter 14
e. Electric over hydraulic cab tilt with manual back-up
f. Single tone cab paint finish with 10 year paint warranty pro -rated
g. Air conditioning and heating
h. Remote controlled mirrors (from driver's position) with separate flat and convex sections
i. DOT compliant headlights
j . Forward facing turn and warning lights
k. Cornering turn and warning lights
1. Minimum four (4) dome lights with red and clear bulbs
m. Minimum four (4) under cab step lights
n. Cab and compartment door ajar light and buzzer
0. One (1) engine compartment light
p. Color coded and function coded wiring
q. Alternator sized according to amp draw report
r. Minimum four (4) 750 CCA batteries
S. Load manager with automatic high idle function
t. Dual air horns with dual in -cab controls
5. AERIAL APPARATUS - ALUMINUM OR STEEL
a. Aerial shall meet or exceed all sections of NFPA 1901 Chapter 19
TR 12430- Exhibit D
Base Specifications # 06 - 75 " Rear Mounted Aerial Apparatus
b. Ladder material: aluminum or steel
C. Rear -mounted configuration
d. 3-section aerial with minimum elevation of 75' per NFPA requirements
e. Rated horizontal reach per NFPA requirements
f. Rungs shall meet all aspects of NFPA 1901 19.2.5
g. Rungs equipped with a slip resistant surface meeting NFPA 1901 19.2.5
h. Rungs spacing meeting NFPA 1901 19.2.5
i. Turntable with pedestal mounted controls meeting NFPA 1901 19.4
j . Aerial rated load capacity not flowing water: 500 lbs. minimum in addition to equipment
mounted at tip of ladder
k. Aerial rated load capacity while flowing 1000 gpm: 500 lbs. minimum in addition to
equipment mounted at tip of ladder
1. Rated load capacities shall meet and /or exceed NFPA 1901 19.3
m. The aerial shall be rated in multiple configurations per Chapter 19.3.4
n. Extend/retract, rotate and hydraulic or electric over hydraulic controls meeting NFPA 1901
19.5 through 19.5.3.6.
o. Hydraulic pressure gauge at turntable controls
p. Illuminated Angle of Elevation Indicator meeting NFPA 1901 19.4.1,
q. Flowmeter on turntable control pedestal meeting NFPA 1901 19.6.8
r. All aerial control devices shall meet NFPA 1901 19.17
S. Fall protection provisions shall be provided.
t. Bidders to state type of stabilizers and overall stabilizers spread
u. Aerial shall meet structural safety factors in accordance with NFPA 1901 19.20
V. Aerial shall meet NFPA 1901 stability safety factors Chapter 19.21
w. Lighted turntable area
X. The aerial manufacturer (the company that manufacturers the entire aerial device) shall
maintain a Quality Control Program in accordance with NFPA 1901 Chapter 19.22
y. Special attention shall be paid to meeting all safety requirements per NFPA 1901 19.20
Z. Aerial shall be fully tested and certified by third party certified testing company per NFPA
1901 19.24 and 19.25
aa. 2-way intercom system between ladder tip and turntable control pedestal.
bb. Minimum 1000 gpm waterway system meeting NFPA 1901 with remote control nozzle
(controls at fly section and at turntable control pedestal) with movable manual pinned
waterway or remote control movable waterway.
cc. Minimum 4" rear waterway inlet with pressure gauge and long handled chrome cap
dd. Minimum 4" waterway discharge with 4" valve with handwheel or electric control on pump
panel
ee. Waterway relief valve and minimum 1.5" drain at rear of apparatus
ff. Stabilizer controls and stabilizer to aerial controls mounted on rear of apparatus body
gg. One (1) high intensity spotlights on ladder tip
hh. Two high intensity flood lights on ladder base
ii. Painted finish on steel aerial -bidder shall provide copy of paint warranty on aerial
Instruction plates and signs must be installed per NFPA 1901 Chapter 19.23
6. FIRE PUMP & PLUMBING
a. Minimum 1250 GPM pump as rated per NFPA 1901 Chapter 16
b. Air operated pump shift
C. Discharge pressure relief valve
d. Intake pressure relief valve
e. Master drain valve
TR 12430- Exhibit D
Base Speciftcations # 06 - 75 " Rear Mounted Aerial Apparatus
f. Electric dry type primer
g. Pump panel lights, 3 each side
h. Pump compartment light
i. OK to pump lights in cab and at pump panel
j . Engine cooler
k. Pump cooler
1. Two (2) 6" steamers, one on side panel
m. 2.5" left side gated suction
n. 1.5" tank fill
o. Two (2) 2" crosslay hose beds over the pump compartment
p. Two (2) 2-1/2" left side discharges
q. Two (2) 2-1/2" right side discharges
r. Stainless steel schedule 10 piping with 10 year warranty
S. Panel gauge package: water tank level, tach, oil pressure, water temperature, voltmeter,
light and alarm system
t. Minimum 300 gallon polypropylene booster tank with lifetime warranty
U. 3" tank to pump connection
V. Minimum 10" x 8" fill tower with minimum 4" overflow tube
W. 15 ft. of soft suction hose sized for capacity of fire pump
7. APPARATUS BODY
a. Bidders to bid on each of their offered construction types:
• Extruded aluminum
• Formed aluminum
• Formed galvanneal steel
• Formed stainless steel
b. Bidders to state thicknesses, alloys and construction methods of all materials used in body
construction
C. High left side compartments
d. High right side compartments
e. Bidders to accurately state the total cubic footage of compartment space, along with each
compartment size
f. Lights in compartments to meet NFPA 1901 Chapter 13.10.5
g. Hose bed lighting must be provided per NFPA Chapter 1901 13.10.2
h. Back up alarm
i. Rear ladder storage for minimum 85' NFPA ground ladders fully enclosed at rear of apparatus,
ladders to be included
j . Rear pike pole storage for minimum of six (6) pike poles fully enclosed at rear of apparatus
k. Slide out pump operator platform
1. Hose bed with hose restraints to be NFPA quint compliant
m. Steps and handrails for climbing from ground to turntable - bidders to state exact design
n. Lights at each step
0. Stop/turn/back up lights
p. DOT clearance and marker lights
q. License plate light
r. Rear deck lights
S. Rub rail along each side of body
t. Running boards at each pump panel
u. Brushed stainless steel or black non -glare aluminum pump panels
TR 12430- Exhibit D
Base Specifications # 06 - 75 " Rear Mounted Aerial Apparatus
0
9.
10.
EMERGENCY WARNING
a. NFPA Zone A lower and upper level lighting
b. NFPA Zone B / D lower level lighting
C. NFPA Zone C upper and lower level lighting
d. Electronic 200 watt siren/PA with minimum
PAINT FINISH/REFLECTIVE STRIPING
100 watt speaker recessed in bumper
a. Cab and body to be painted single tone with 10 year pro -rated paint and corrosion perforation
warranty
b. Wheels painted to match the cab and body
C. Reflective striping in accordance with Chapter 15.9.3
d. Reflective chevron on rear of apparatus in accordance with Chapter
15.9.3.2.
a. 1 year bumper to bumper mechanical, excluding normal wear and tear items
b. 10 year cab and body structural
C. 10 year paint pro -rated
d. 10 year corrosion perforation on cab and body
e. 20 year aerial structural
f. Lifetime frame warranty
g. 2 year front axle
h. 2 year rear axle
i. 5 year engine
j . 5 year fire pump
k. Lifetime booster tank
1. Manufacturer's standard 5 year warranty for transmission
TR 12430- Exhibit D
FLORIDA
ASSOCI ATIO OF
COOTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 75' REAR MOUNTED AERIAL APPARATUS
Specification #06
(Extruded Aluminum Body - Aluminum Ladder)
The 75' Rear Mounted Aerial Apparatus, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL: E-ONE HP 75
BASE PRICE: $519,797.00
MANUFACTURER: Hall -Mark Fire Apparatus (E-ONE)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current. NFPA 1901, (2009 edition)
and all chapters that are appropriate for a quint apparatus with a special emphasis on Chapters 1,
29 3, 4, 99 12, 139 149 159 16, 189 199 FMVSS (applicable areas) and NHTSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION OF
COUNTIES
AU About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 75' REAR MOUNTED AERIAL APPARATUS
Specification #06
(Extruded Aluminum Body - Steel Ladder)
The 75' Rear Mounted Aerial Apparatus, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL: Crimson 75RMA
BASE PRICE: $5659033.00
MANUFACTURER: Crimson Fire (Public Safety...)
MODEL: Intruder
BASE PRICE: $499, 648.00
MANUFACTURER: Ferrara Fire Apparatus, Inc.
Igniter XD
$551,566.00
Ferrara Fire Apparatus, Inc.
Spartan Metro Star 75'
$5101,188.00
Rosenbauer South Dakota, LLC
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a quint apparatus with a special emphasis on Chapters 1,
29 39, 4, 9, 129 139 14, 159 169 18, 19, FMVSS (applicable areas) and NHTSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLOR.IDA
ASSOCINHON OF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 75' REAR MOUNTED AERIAL APPARATUS
Specification #06
(Formed Aluminum Body -Aluminum Ladder)
The 75' Rear Mounted Aerial Apparatus, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL: Pierce Impel 75' HDL
BASE PRICE: $5559691.00
MANUFACTURER: Pierce Manufacturing, Inc.
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a quint apparatus with a special emphasis on Chapters 1,
2, 31, 49 99 129 13, 149 159 16, 189 199 FMVSS (applicable areas) and NSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
F.LOR.IDA
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 75' REAR MOUNTED AERIAL APPARATUS
Specification #06
(Formed Aluminum Body - Steel Ladder)
The 75' Rear Mounted Aerial Apparatus, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL: American LaFrance 75RML
BASE PRICE: $5811,901.00
MANUFACTURER: American LaFrance, LLC
MODEL:
BASE PRICE:
MANUFACTURER:
MODEL:
BASE PRICE:
MANUFACTURER:
KME Predator AerialCat FL0675
$5879390.00
Kovatch Mobile Equip. Corp. (KME)
Spartan Metro Star 75'
$4991,929.00
Rosenbauer South Dakota, LLC
Crimson 75RMA
$5469291.00
Crimson Fire (Public Safety...)
Pierce Impel 75' HDL
$5559141,00
Pierce Manufacturing, Inc.
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a quint apparatus with a special emphasis on Chapters 1,
2, 3, 49 99 129 139 14, 159 16, 189 199 FMVSS (applicable areas) and NHTSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION OF
Cf»TIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 75' REAR MOUNTED AERIAL APPARATUS
Specification #06
(Formed Stainless Steel Body -Steel Ladder)
The 75' Rear Mounted Aerial Apparatus, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL: American LaFrance 75RML Crimson 75RMA
BASE PRICE: $5849987.00 $5729135.00
MANUFACTURER: American La.France, LLC Crimson Fire (Public Safety... )
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a quint apparatus with a special emphasis on Chapters 1,
2, 39 49 99 129, 13, 149, 159 169 18, 19, FMVSS (applicable areas) and NHTSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION -Of
COLTN'TIES
AU About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF, COUNTIES
Base Specifications
PECIFICATION #07 - 100' MID MOUNTED
ALL ITEMS FACTORY INSTALLED UNLESS OTHERWISE INDICATED
THE CAB AND CHASSIS SHALL BE PROVIDED BY THE BODY MANUFACTURER
1. DOCUMENTATION, DELIVERY. TRAINING
a. When requested by end user, bidders to accurately state wheelbase, cab to axle, overall length,
bumper swing turn radius, curb -to -curb turning radius, overall height, overall width, GVWR,
angle of approach, angle of departure and SCAAN certification for drivetrain compatibility in
submitted specifications
b. Approval drawings provided prior to construction commencement
c. Two (2) sets of operator and service manuals
d. Delivery to be F.O.B. customer's location
e. Three (3) days of training by employee of manufacturer
f. Pump test certification by independent third party
g. Water tank capacity certification
h. Aerial non-destructive, performance and stability testing by independent third party
i. 12 volt and, if applicable, 110 volt testing by independent third party
j . Vehicle weight, as measured by certified scales
2. CHASSIS
a. 110,000 psi heat treated steel frame rail with full length inner 110,000 psi C-channel liner
or integral torque box frame
b. 10 gauge polished stainless steel 16" to 24" extended front bumper with aluminum diamond
plate gravel shield
C. Tow hooks or eyes front and rear attached to the frame
d. 22,500 pound minimum front axle, suspension, tubeless radial tires, steel disc wheels
e. 40,000 pound minimum rear axle, suspension, tubeless radial tires, steel disc wheels
f. Front and rear mud flaps
g. NFPA 1901 Chapter 4.15.3 top speed rating requirement
h. S-cam air brakes or equivalent, as large as possible, with automatic slack adjusters
TR 12430- Exhibit D
Base Specif[cations #07 - 100" Mid Mounted Aerial Apparatus
i. Manufacturer's standard compressor
j . Minimum 5000 cubic inch air reservoir capacity
k. Air dryer, color coded air lines, turn drain valves on reservoirs
1. ABS brakes
m. Power steering with tilt/telescopic wheel
n. Vehicle data recorder (VDR) in compliance with Chapter 4.11 with required software meeting
4.11.8
0. Electronic Stability Control shall be provided in compliance with NFPA 1901 Chapter 4.13.1.2
if the manufacturer cannot comply with Chapters 4.13.1.1 through 4.13.1.1.3.2.
p. Tire pressure monitoring system with Chapter 4.13.4
3. POWERTRAIN
a. Minimum 450 horsepower turbocharged diesel engine with 1450 ft. lb. torque rating
b. Engine exhaust at front of right rear wheels
C. Secondary braking to meet NFPA
d. Engine manufacturer's statement of engine installation approval with approved cooling system
e. Drivelines to meet engine torque rating
f. Silicone coolant hoses with constant torque clamps
g. EVS 4000 automatic transmission
h. 50 gallon minimum fuel tank
i. OEM oil, fuel, transmission filters
4. CAB
a. Medium length tilt aluminum cab meeting NFPA 1901 Chapter 14.3.2
b. Seating for four, three in SCBA seats with SCBA brackets
C. Air ride driver seat, all others fixed position
d. All persons in 3-point seat belts per Chapter 14, seats equipped with seat belt/occupant
detection/warning system per Chapter 14
e. Electric over hydraulic cab tilt with manual back-up
f. Single tone cab paint finish with 10 year paint warranty pro -rated
g. Air conditioning and heating
h. Remote controlled mirrors (from driver's position) with separate flat and convex sections
i. DOT compliant headlights
j . Forward facing turn and warning lights
k. Cornering turn and warning lights
1. Minimum four (4) dome lights with red and clear bulbs
m. Minimum four (4) under cab step lights
n. Cab and compartment door ajar light and buzzer
0. One (1) engine compartment light
p. Color coded and function coded wiring
q. Alternator sized according to amp draw report
r. Minimum four (4) 750 CCA batteries
S. Load manager with automatic high idle function
t. Dual air horns with dual in -cab controls
5. AERIAL APPARATUS - ALUMINUM OR STEEL
a. Aerial shall meet or exceed all sections of NFPA 1901 Chapter 19
b. Ladder material: aluminum or steel
C. Mid -mounted configuration
TR 12430- Exhibit D
Base Specifications #07 - 100' Mid Mounted Aerial Apparatus
d. 5-section aerial with minimum elevation of 100' per NFPA reqirements
e. Rated horizontal reach per NFPA requirements
f. Rungs shall meet all aspects of NFPA 1901 19.2.5
g. Rungs equipped with a slip resistant surface meeting NFPA 1901 19.2.5
h. Rungs spacing meeting NFPA 1901 19.2.5
i. Turntable with pedestal mounted controls meeting NFPA 1901 19.4
j . Aerial rated load capacity not flowing water: 500 lbs. minimum in addition to equipment
mounted at tip of ladder
k. Aerial rated load capacity while flowing 1000 gpm: 500 lbs. minimum in addition to equipment
mounted at tip of ladder
1. Rated load capacities shall meet and /or exceed NFPA 1901 19.3
m. The aerial shall be rated in multiple configurations per Chapter 19.3.4
n. Extend/retract, rotate and hydraulic or electric over hydraulic controls meeting NFPA 1901
19.5 through 19.5.3.6.
o. Hydraulic pressure gauge at turntable controls
p. Illuminated Angle of Elevation Indicator meeting NFPA 1901 19.4.1
q. Flowmeter on turntable control pedestal meeting NFPA 1901 19.6.8
r. All aerial control devices shall meet NFPA 1901 19.17
S. Fall protection provisions shall be provided.
t. Bidders to state type of stabilizers and overall stabilizers spread
u. Aerial shall meet structural safety factors in accordance with NFPA 1901 19.20
V. Aerial shall meet NFPA 1901 stability safety factors Chapter 19.21
w. Lighted turntable area
X. The aerial manufacturer (the company that manufacturers the entire aerial device) shall
maintain a Quality Control Program in accordance with NFPA 1901 Chapter 19.22
y. Special attention shall be paid to meeting all safety requirements per NFPA 1901 19.20
Z. Aerial shall be fully tested and certified by third party certified testing company per NFPA
1901 19.24 and 19.25
aa. 2-way intercom system between ladder tip and turntable control pedestal.
bb. Minimum 1000 gpm waterway system meeting NFPA 1901 with remote control nozzle (controls
at fly section and at turntable control pedestal) with movable manual pinned waterway or
remote control movable waterway.
cc. Minimum 4" waterway discharge with 4" valve with handwheel or electric control on pump
panel
dd. Minimum 4" waterway inlet (non -gated) on rear or on side of body per NFPA 1901 Chapter
19.6.6
ee. Waterway relief valve and minimum 1.5"drain
ff. Stabilizer controls and stabilizer to aerial controls mounted on rear of apparatus body
gg. One (1) high intensity spotlights on ladder tip
hh. Two high intensity flood lights on ladder base
ii. Painted finish on steel aerial -bidder shall provide copy of paint warranty on aerial
jj. Instruction plates and signs must be installed per NFPA 1901 Chapter 19.23
6. FIRE PUMP & PLUMBING
a. Minimum 1500 GPM pump as rated per NFPA 1901
b. Air operated pump shift
C. Discharge pressure relief valve
d. Intake pressure relief valve
e. Master drain valve
f. Electric dry type primer
g. Pump panel lights, 3 each side
Chapter 16
TR 12430- Exhibit D
Base Specifications #07 - 100" Mid Mounted Aerial Apparatus
h. Pump compartment light
i. OK to pump lights in cab and at pump pane
j . Engine cooler
k. Pump cooler
1. Two (2) 6" steamers, one on side panel
m. 2.59' left side gated suction
n. 1.5" tank fill
o. Two (2) 2" crosslay hose beds over the pump compartment
p. Two (2) 2-1 /2" left side discharges
q. Two (2) 2-1/2" right side discharges
r. Stainless steel schedule 40 piping with 10 year warranty
S. Panel gauge package: water tank level, tach, oil pressure, water temperature, voltmeter, light
and alarm system
t. Minimum 300 gallon polypropylene booster tank with lifetime warranty
u. 3" tank to pump connection
V. Minimum 10" x 8" fill tower with minimum 4" overflow tube
W. 15 ft. of soft suction hose sized for capacity of fire pump
7. APPARATUS BODY
a. Bidders to bid on each of their offered construction types:
• Extruded aluminum
• Formed aluminum
Formed galvanneal steel
• Formed stainless steel
b. Bidders to state thicknesses, alloys and construction methods of all materials used in body
construction
C. High left side compartments
d. High right side compartments
e. Bidders to accurately state the total cubic footage of compartment space, along with each
compartment size
f. Lights in compartments to meet NFPA 1901 Chapter 13.10.5
g. Hose bed lighting must be provided per NFPA Chapter 1901 13.10.2
h. Back up alarm
i. Rear ladder storage for minimum 11 5'NFPA ground ladders fully enclosed at rear of apparatus,
ladders to be included
j . Rear pike pole storage for minimum of six (6) pike poles fully enclosed at rear of apparatus
k. Slide out pump operator platform
1. Hose bed with hose restraints to be NFPA quint compliant
m. Steps and handrails for climbing from ground to turntable - bidders to state exact design
n. Lights at each step
0. Stop/turn/back up lights
p. DOT clearance and marker lights
q. License plate light
r. Rear deck lights
S. Rub rail along each side of body
t. Running boards at each pump panel
u. Brushed stainless steel or black non -glare aluminum pump panels
TR 12430- Exhibit D
Base Specifications #07 - 100" Mid Mounted Aerial Apparatus
8. EMERGENCY WARNING
a. NFPA Zone A lower and upper level lighting
b. NFPA Zone B / D lower level lighting
C. NFPA Zone C upper and lower level lighting
d. Electronic 200 watt siren/PA with minimum 100 watt speaker recessed in bumper
9. PAINT FINISH/REFLECTIVE STRIPING
a. Cab and body to be painted single tone with 10 year pro -rated paint and corrosion perforation
warranty
b. Wheels painted to match the cab and body
C. Reflective striping in accordance with Chapter 15.9.3
d. Reflective chevron on rear of apparatus in accordance with Chapter 15.9.3.2.
a. 1 year bumper to bumper mechanical, excluding normal wear and tear items
b. 10 year cab and body structural
C. 10 year paint pro -rated
d. 10 year corrosion perforation on cab and body
e. 20 year aerial structural
f. Lifetime frame warranty
g. 2 year front axle
h. 2 year rear axle
j . 5 year fire pump
k. Lifetime booster tank
1. Manufacturer's standard 5 year warranty for transmission
TR 12430- Exhibit D
FLORIDA` �^
I,NTION OF
COL NTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 100' NIID MOUNTED AERIAL APPARATUS
Specification #07
(Extruded Aluminum Body - Steel Ladder)
The 100' Mid Mounted Aerial Apparatus, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base, price as awarded by
manufacturer by specification.
MODEL: Igniter XD Spectr
BASE PRICE: $7551,677.00 $7331,191.00
MANUFACTURER: Ferrara Fire Apparatus, Inc. Ferrara Fire Apparatus, Inc.
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a quint apparatus with a special emphasis on Chapters 1,
2, 39 49 99, 129 139 14, 159 169 18, 19, FMVSS (applicable areas) and NHTSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA.
OCIATKYN OF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 100' MID MOUNTED AERIAI. APPARATUS
Specification #07
(Formed Aluminum Body -Steel Ladder)
The 100' Mid Mounted Aerial Apparatus, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL: KME Predator AerialCat FL07100 Pierce Arrow XT HDL
BABE PRICE: $8001,204.00 $7531,201.00
MANUFACTURER: Kovatch Mobile Equip. Corp. (KME) Pierce Manufacturing, Inc.
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a quint apparatus with a special emphasis on Chapters 1,
29 31, 4, 9, 129 139 14, 159 16, 189 19, FMVSS (applicable areas) and NHTSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCLAMOIN" OF
COUNTEES
All About 11orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 100' NIID MOUNTED AERIAL APPARATUS
Specification #07
(Formed Stainless Steel Body - Aluminum Ladder)
The 100' Mid Mounted Aerial Apparatus, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSNs base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL: Sutphen SL 100
BASE PRICE: $7449 560.00
MANUFACTURER: Sutphen Corporation
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a quint apparatus with a special emphasis on Chapters 1,
2, 39 41 9, 12, 13, 14, 159 169 18, 19, FMVSS (applicable areas) and NHTSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION OF
COUNTIES
All About 141oridd
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
Base Specifications*wns
SPECIFICATION #08 - 100' REAR MOUNTED
FiMz"
�1 FW41;J V41 ZT04
ALL ITEMS FACTORY INSTALLED UNLESS OTHERWISE INDICATED
THE CAB AND CHASSIS SHALL BE PROVIDED BY THE BODY MANUFACTURER
1. DOCUMENTATION, DELIVERY, TRAINING
a. When requested by end user, bidders to accurately state wheelbase, cab to axle, overall length,
bumper swing turn radius, curb -to -curb turning radius, overall height, overall width, GVWR,
angle of approach, angle of departure and SCAAN certification for drivetrain compatibility
in submitted specifications
b. Approval drawings provided prior to construction commencement
C. Two (2) sets of operator and service manuals
d. Delivery to be F.O.B. customer's location
e. Three (3) days of training by employee of manufacturer
f. Pump test certification by independent third party
g. Water tank capacity certification
h. Aerial non-destructive, performance and stability testing by independent third party
i. 12 volt and, if applicable, 110 volt testing by independent third party
j . Vehicle weight, as measured by certified scales
2. CHASSIS
a. 110,000 psi heat treated steel frame rail with full length inner 110,000 psi C-channel liner
or integral torque box frame
b. 10 gauge polished stainless steel 16" to 24" extended front bumper with aluminum diamond
plate gravel shield
C. Tow hooks or eyes front and rear attached to the frame
d. 20,000 pound minimum front axle, suspension, tubeless radial tires, steel disc wheels
e. 48,000 pound minimum rear axle, suspension, tubeless radial tires, steel disc wheels
f. Front and rear mud flaps
g. NFPA 1901 Chapter 4.15.3 top speed rating requirement
h. S-cam air brakes or equivalent, as large as possible, with automaticslack adjusters
TR 12430- Exhibit D
Base Specifications #08 - I00' Rear Mounted Aerial Apparatus
i. Manufacturer's standard compressor
j . Minimum 5000 cubic inch air reservoir capacity
k. Air dryer, color coded air lines, turn drain valves on reservoirs
1. ABS brakes
m. Power steering with tilt/telescopic wheel
n. Vehicle data recorder (VDR) in compliance with Chapter 4.11 with required software meeting
4.11.8
0. Electronic Stability Control shall be provided in compliance with NFPA 1901 Chapter 4.13.1.2
if the manufacturer cannot comply with Chapters 4.13.1.1 through 4.13.1.1.3.2.
p. Tire pressure monitoring system with Chapter 4.13.4
3. POWERTRAIN
a. Minimum 450 horsepower turbocharged diesel engine with 1450 ft. lb. torque rating
b. Engine exhaust at front of right rear wheels
C. Secondary braking to meet NFPA
d. Engine manufacturer's statement of engine installation approval with approved cooling system
e. Drivelines to meet engine torque rating
f. Silicone coolant hoses with constant torque clamps
g. EVS 4000 automatic transmission
h. 50 gallon minimum fuel tank
i. OEM oil, fuel, transmission filters
4. CAB
a. Medium length tilt aluminum cab meeting NFPA 1901 Chapter 14.3.2
b. Seating for four, three in SCBA seats with SCBA brackets
c. Air ride driver seat, all others fixed position
d. All persons in 3-point seat belts per Chapter 14, seats equipped with seat belt/occupant
detection/warning system per Chapter 14
e. Electric over hydraulic cab tilt with manual back-up
f. Single tone cab paint finish with 10 year paint warranty pro -rated
g. Air conditioning and heating
h. Remote controlled mirrors (from driver's position) with separate flat and convex sections
i. DOT compliant headlights
j . Forward facing turn and warning lights
k. Cornering turn and warning lights
1. Minimum four (4) dome lights with red and clear bulbs
m. Minimum four (4) under cab step lights
n. Cab and compartment door ajar light and buzzer
o. One (1) engine compartment light
p. Color coded and function coded wiring
q. Alternator sized according to amp draw report
r. Minimum four (4) 750 CCA batteries
S. Load manager with automatic high idle function
t. Dual air horns with dual in -cab controls
5. AERIAL APPARATUS - ALUMINUM OR STEEL
a.
Aerial shall meet
or exceed all
sections of NFPA 1901 Chapter 19
b.
Ladder material:
aluminum or
steel
TR 12430- Exhibit D
Base Specifications #08 - 100' Rear Mounted Aerial Apparatus
C. Rear -mounted configuration
d. 4-section aerial with minimum elevation of 100' per NFPA requirements
e. Rated horizontal reach per NFPA requirements
f. Rungs shall meet all aspects of NFPA 1901 19.2.5
g. Rungs equipped with a slip resistant surface meeting NFPA 1901 19.2.5
h. Rungs spacing meeting NFPA 1901 19.2.5
i. Turntable with pedestal mounted controls meeting NFPA 1901 19.4
j . Aerial rated load capacity not flowing water: 500 lbs. minimum
in addition to equipment mounted at tip of ladder
k. Aerial rated load capacity while flowing 1000 gpm: 500 lbs. minimum in addition to equipment
mounted at tip of ladder
1. Rated load capacities shall meet and /or exceed NFPA 1901 19.3
m. The aerial shall be rated in multiple configurations per Chapter 19.3.4
n. Extend/retract, rotate and hydraulic or electric over hydraulic controls meeting NFPA 1901
19.5 through 19.5.3.6.
0. Hydraulic pressure gauge at turntable controls
p. Illuminated Angle of Elevation Indicator meeting NFPA 1901 19.4.1
q. Flowmeter on turntable control pedestal meeting NFPA 1901 19.6.8
r. All aerial control devices shall meet NFPA 1901 19.17
S. Fall protection provisions shall be provided.
t. Bidders to state type of stabilizers and overall stabilizers spread
u. Aerial shall meet structural safety factors in accordance with NFPA 1901 19.20
V. Aerial shall meet NFPA 1901 stability safety factors Chapter 19.21
w. Lighted turntable area
x. The aerial manufacturer (the company that manufacturers the entire aerial device) shall
maintain a Quality Control Program in accordance with NFPA 1901 Chapter 19.22
y. Special attention shall be paid to meeting all safety requirements per NFPA 1901 19.20
Z. Aerial shall be fully tested and certified by third party certified testing company per NFPA
1901 19.24 and 19.25
aa. 2-way intercom system between ladder tip and turntable control pedestal.
bb. Minimum 1000 gpm waterway system meeting NFPA 1901 with remote control nozzle (controls
at fly section and at turntable control pedestal) with. movable manual pinned waterway or
remote control movable waterway.
cc. Minimum 4" rear waterway inlet with pressure gauge and long handled chrome cap
dd. Minimum 4" waterway discharge with 4" valve with handwheel or electric control on pump
panel
ee. Waterway relief valve and minimum 1.5" drain at rear of apparatus
ff. Stabilizer controls and stabilizer to aerial controls mounted on rear of apparatus body
gg. One (1) high intensity spotlights on ladder tip
hh. Two high intensity flood lights on ladder base
ii. Painted finish on steel aerial -bidder shall provide copy of paint warranty on aerial
jj . Instruction plates and signs must be installed per NFPA 1901 Chapter 19.23
6. FIRE PUMP & PLUMBING
a. Minimum 1500 GPM pump as rated per NFPA 1901 Chapter 16
b. Air operated pump shift
C. Discharge pressure relief valve
d. Intake pressure relief valve
e. Master drain valve
f. Electric dry type primer
TR 12430- Exhibit D
Base Specifications #08 - 100" Rear Mounted Aerial Apparatus
g. Pump panel lights, 3 each side
h. Pump compartment light
i. OK to pump lights in cab and at pump pane
j . Engine cooler
k. Pump cooler
1. Two (2) 6" steamers, one on side panel
m. 2.5" left side gated suction
n. 1.5"' tank fill
o. Two (2) 2" crosslay hose beds over the pump compartment
p. Two (2) 2-1/2" left side discharges
q. Two (2) 2-1/2" right side discharges
r. Stainless steel schedule 40 piping with 10 year warranty
S. Panel gauge package: water tank level, tach, oil pressure, water temperature, voltmeter, light
and alarm system
t. Minimum 300 gallon polypropylene booster tank with lifetime warranty
U. 3" tank to pump connection
V. Minimum 10" x 8" fill tower with minimum 4" overflow tube
W. 15 ft. of soft suction hose sized for capacity of fire pump
7. APPARATUS BODY
a. Bidders to bid on each of their offered construction types:
• Extruded aluminum
• Formed aluminum
• Formed galvanneal steel
• Formed stainless steel
b. Bidders to state thicknesses, alloys and construction methods of all materials used in body
construction
C. High left side compartments
d. High right side compartments
e. Bidders to accurately state the total cubic footage of compartment space, along with each
compartment size
f. Lights in compartments to meet NFPA 1901 Chapter 13.10.5
g. Hose bed lighting must be provided per NFPA Chapter 1901 13.10.2
h. Back up alarm
i. Rear ladder storage for minimum 1 15'NFPA ground ladders fully enclosed at rear of apparatus,
ladders to be included
j . Rear pike pole storage for minimum of six (6) pike poles fully enclosed at rear of apparatus
k. Slide out pump operator platform
1. Hose bed with hose restraints to be NFPA quint compliant
m. Steps and handrails for climbing from ground to turntable - bidders to state exact design
n. Lights at each step
0. Stop/turn/back up lights
p. DOT clearance and marker lights
q. License plate light
r. Rear deck lights
S. Rub rail along each side of body
t. Running boards at each pump panel
u. Brushed stainless steel or black non -glare aluminum pump panels
TR 12430- Exhibit D
Base Specifications #08 - 1OO" Rear Mounted Aerial Apparatus
A
9.
10.
EMERGENCY WARNING
a. NFPA Zone A lower and upper level lighting
b. NFPA Zone B / D lower level lighting
C. NFPA Zone C upper and lower level lighting
d. Electronic 200 watt siren/PA with minimum
PAINT FINISH/REFLECTIVE STRIPING
100 watt speaker recessed in bumper
a. Cab and body to be painted single tone with 10 year pro -rated paint and corrosion perforation
warranty
b. Wheels painted to match the cab and body
C. Reflective striping in accordance with Chapter 15.9.3
d. Reflective chevron on rear of apparatus in accordance with Chapter
1.:::: ►M111
15.9.3.2.
a. 1 year bumper to bumper mechanical, excluding normal wear and tear items
b. 10 year cab and body structural
C. 10 year paint pro -rated
d. 10 year corrosion perforation on cab and body
e. 20 year aerial structural
f. Lifetime frame warranty
g. 2 year front axle
h. 2 year rear axle
j . 5 year fire pump
k. Lifetime booster tank
1. Manufacturer's standard 5 year warranty for transmission
TR 12430- Exhibit D
F,tEOR�a^�IDA
IONNOF
COUNTIES
All About blorida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 100' REAR MOUNTED AERIAL APPARATUS
Specification #08
(Extruded Aluminum Body - Aluminum Ladder)
The 1 00'Rear Mounted Aerial Apparatus, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL: E-ONE HP TOOL
BASE PRICE: $6931366.00
MANUFACTURER: Hall -Mark Fire Apparatus (E-ONE)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a quint apparatus with a special emphasis on Chapters 1,
29 39 49, 8, 12, 139 149 159 169 189 19, FMVSS (applicable areas) and NHTSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
F"EORIDA
A:SSOC ATION O
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 100' REAR MOUNTED AERIAL APPARATUS
Specification #08
(Extruded Aluminum Body - Steel Ladder)
The 1 00'Rear Mounted Aerial Apparatus, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price -as awarded by
manufacturer by specification.
MODEL:
BASE PRICE:
MANUFACTURER:
MODEL:
BASE PRICE.
MANUFACTURER:
Crimson 100RMA
$674,072.00
Crimson Fire (Public Safety...)
Spectr
$6311,376.00
Ferrara Fire Apparatus, Inc.
Igniter XD
$6629036.00
Ferrara Fire Apparatus, Inc.
Spartan Gladiator 100'
$6521394.00
Rosenbauer South Dakota, LLC
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a quint apparatus with a special emphasis on Chapters 1,
2, 3, 49 89 129 13, 14, 159 169, 18, 19, FMVSS (applicable areas) and NHTSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any .options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
I
TR 12430- Exhibit D
FEORIDA
ASSOCIATION O
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 100' REAR MOUNTED AERIAL APPARATUS
Specification #08
(Formed Aluminum Body - Aluminum Ladder)
The 1 00'Rear Mounted Aerial Apparatus, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL: Pierce Arrow XT HDL
BASE PRICE: $6659648.00
MANUFACTURER: Pierce Manufacturing, Inc.
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a quint apparatus with a special emphasis on Chapters 1,
2, 3, 41, 8, 12, 139 14, 15, 16, 189 19, FMVSS (applicable areas) and NHTSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as, a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION OF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 100' REAR MOUNTED AERIAL APPARATUS
Specification #08
(Formed Aluminum Body - Steel Ladder)
The 1 00'Rear Mounted Aerial Apparatus, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL: American LaFrance 100RMA
BASE PRICE: $7509442.00
MANUFACTURER: American LaFrance, LLC
MODEL: Pierce Arrow XT HDL
BASE PRICE: $6539206.00
MANUFACTURER: Pierce Manufacturing, Inc.
KME Predator AerialCat FLOS 103
$6671,180.00
Kovatch Mobile Equip. Corp. (KME)
Spartan Gladiator 100'
$6201,552.00
Rosenbauer South Dakota, LLC
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a quint apparatus with a special emphasis on Chapters 1,
2, 39 4, 89 12, 13, 149 151, 16, 181, 19, FMVSS (applicable areas) and NHTSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION OF
COOTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 100' REAR MOUNTED AERIAL APPARATUS
Specification #08
(Pori ed Stainless Steel Body - Aluminum Ladder)
The 1 00'Rear Mounted Aerial Apparatus, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL: Pierce Arrow XT HAL-SS
BASE PRICE: $6731,564.00
MANUFACTURER: Pierce Manufacturing, Inc.
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a quint apparatus with a special emphasis on Chapters 1,
29 39 41 8, 129 139 14, 15, 169 189 19, FMVSS (applicable areas) and NHTSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA.. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION OF
COUNTIES
Asti About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 100' REAR MOUNTED AERIAL APPARATUS
Specification #08
(Formed Stainless Steel Body - Steel Ladder)
The 100' Rear Mounted Aerial Apparatus, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL: American LaFrance 100RMA Crimson 100RMA
BASE PRICE: $7531,942.00 $6771,950.00
MANUFACTURER: American LaFrance, LLC Crimson Fire (Public Safety...)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a quint apparatus with a special emphasis on Chapters 1,
29 39 4, 8, 12, 139 14, 159 16, 18, 199 FMVSS (applicable areas) and NHTSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
F'I..ORIDA
ASSOCIATION OF
COUNTIES
AU About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
Base Specifications
FICATION #09 -
AERIAL PLATFORM
ALL ITEMS FACTORY INSTALLED UNLESS OTHERWISE INDICATED
THE CAB AND CHASSIS SHALL BE PROVIDED BY THE BODY MANUFACTURER
1. DOCUMENTATION. DELIVERY. TRAINING
a. When requested by end user, bidders to accurately state wheelbase, cab to axle, overall length,
bumper swing turn radius, curb -to -curb turning radius, overall height, overall width, GVWR,
angle of approach, angle of departure and SCAA.N certification for drivetrain compatibility in
submitted specifications
b. Approval drawings provided prior to construction commencement
C. Two (2) sets of operator and .service manuals
d. Delivery to be F.O.B. customer's location
e. Three (3) days of training by employee of manufacturer
f. Pump test certification by independent third party
g. Water tank capacity certification by independent third party
h. Aerial non-destructive, waterway flow test, performance and stability testing by independent
third party
i. 12 volt and, if applicable, 110 volt testing by independent third party
j . Vehicle weight, as measured by certified scales
2. CHASSIS
a. 110,000 psi heat treated steel frame rail with full length inner 110,000 psi C-channel liner
or integral torque box frame
b. 10 gauge polished stainless steel 16" to 24" extended front bumperwith aluminum diamond
plate gravel shield
C. Tow hooks or eyes front and rear attached to the frame
d. 22,500 pound minimum front axle, suspension, tubeless radial tires, steel disc wheels
e. 52,000 pound minimum rear axle, suspension, tubeless radial tires, steel disc wheels
f. Front and rear mud flaps
g. NFPA 1901 Chapter 4.15.3 top speed rating requirement
TR 12430- Exhibit D
Base Specifications #09 -Mid Mounted Aerial Platform
h. S-cam air brakes or equivalent, as large as possible, with automatic slack adjusters
i. Manufacturer's standard compressor
j . Minimum 5000 cubic inch air reservoir capacity
k. Air dryer, color coded air lines, turn drain valves on reservoirs
1. ABS brakes
m. Power steering with tilt/telescopic wheel
n. Vehicle data recorder (VDR) in compliance with Chapter 4.11 with required software meeting
4.11.8
o. Electronic Stability Control shall be provided in compliance with NFPA 1901 Chapter 4.13.1.2
if the manufacturer cannot comply with Chapters 4.13.1.1 through 4.13.1.1.3.2.
p. Tire pressure monitoring system with Chapter 4.13.4
3. POWERTRAIN
a. Minimum 450 horsepower turbocharged diesel engine with 1450 ft. lb. torque rating
b. Engine exhaust at front of right rear wheels
C. Secondary braking to meet NFPA
d. Engine manufacturer's statement of engine installation approval with approved cooling system
e. Drivelines to meet engine torque rating
f. Silicone coolant hoses with constant torque clamps
g. EVS 4000 automatic transmission
h. 50 gallon minimum fuel tank
i. OEM oil, fuel, transmission filters
4. CAB
a. Medium length tilt aluminum cab meeting NFPA 1901 Chapter 14.3.2
b. Seating for four, three in SCBA seats with SCBA brackets
c. Air ride driver seat, all others fixed position
d. All persons in 3-point seat belts per Chapter 14, seats equipped with seat belt/occupant
detection/warning system per Chapter 14
e. Electric over hydraulic cab tilt with manual back-up
f. Single tone cab paint finish with 10 year paint warranty pro -rated
g. Air conditioning and heating
h. Remote controlled mirrors (from driver's position) with separate flat and convex sections
i. DOT compliant headlights
j . Forward facing turn and warning lights
k. Cornering turn and warning lights
1. Minimum four (4) dome lights with red and clear bulbs
m. Minimum four (4) under cab step lights
n. Cab and compartment door ajar light and buzzer
o. One (1) engine compartment light
p. Color coded and function coded wiring
q. Alternator sized according to amp draw report
r. Minimum four (4) 750 CCA batteries
S. Load manager with automatic high idle function
t. Dual air horns with dual in -cab controls
5. AERIAL APPARATUS - ALUMINUM OR STEEL
a. Aerial shall meet or exceed all sections of NFPA 1901 Chapter 19
TR 12430- Exhibit D
Base Specifications #09 - Mid Mounted Aerial Platform
b. Ladder material: aluminum or steel
C. Mid -mounted configuration
d. 4-section or 5-section aerial with minimum elevation of 95' per NFPA requirements
e. Rated horizontal reach per NFPA requirements
f. Rungs shall meet all aspects of NFPA 1901 19.2.5
g. Rungs equipped with a slip resistant surface meeting NFPA 1901 19.2.5
h. Rungs spacing meeting NFPA 1901 19.2.5
i. Turntable with pedestal mounted controls meeting NFPA 1901 19.4
j . Platform rated load capacity not flowing water: 1000 lbs. plus equipment
k. Platform rated load capacity while flowing 1000 gpm: 500 lbs. in addition to permanently
affixed equipment
1. Rated load capacities shall meet and /or exceed NFPA 1901 19.3
m. The aerial shall be rated in multiple configurations per Chapter 19.3.4
n. Extend/retract, rotate and hydraulic or electric over hydraulic controls meeting NFPA 1901
19.5 through 19.5.3.6.
o. Hydraulic pressure gauge at turntable controls
p. Illuminated Angle of Elevation Indicator meeting NFPA 1901 19.4.1
q. Flowmeter on turntable control pedestal meeting NFPA 1901 19.6.8
r. All aerial control devices shall meet NFPA 1901 19.17
S. Fall protection provisions shall be provided.
t. Bidders to state type of stabilizers and overall stabilizers spread
u. Aerial shall meet structural safety factors in accordance with NFPA 1901 19.20
V. Aerial shall meet NFPA 1901 stability safety factors Chapter 19.21
w. Lighted turntable area
X. The aerial manufacturer (the company that manufacturers the entire aerial device) shall
maintain a Quality Control Program in accordance with NFPA 1901 Chapter 19.22
y. Special attention shall be paid to meeting all safety requirements per NFPA 1901 19.20
Z. Aerial shall be fully tested and certified by third party certified testing company per NFPA
1901 19.24 and 19.25
aa. 2-way intercom system between ladder tip and turntable control pedestal.
bb. Minimum 1000 gpm waterway system meeting NFPA 1901 with remote control nozzle (controls
in platform and at turntable control pedestal).
cc. Minimum 4" rear or side waterway inlet with pressure gauge and long handled chrome cap
dd. Minimum 4" waterway discharge with 4" valve with handwheel or electric control on pump
panel
ee. Waterway relief valve and minimum 1.5" drain
ff. Stabilizer controls and stabilizer to aerial controls mounted on center or rear of apparatus
body
gg. One (1) high intensity spotlights on ladder tip
hh. Two high intensity flood lights on ladder base
ii. Painted finish on steel aerial -bidder shall provide copy of paint warranty on aerial
Instruction plates and signs must be installed per NFPA 1901 Chapter 19.23
kk. Platform construction and design must meet NFPA 1901 Chapter 19.7.6
11. Platform operating positions must meet NFPA 1901 Chapter 19.9
6. FIRE PUMP & PLUMBING
a. Minimum 1500 GPM pump as rated per NFPA 1901 Chapter 16
b. Air operated pump shift
C. Discharge pressure relief valve
d. Intake pressure relief valve
TR 12430- Exhibit D
Base Specifications #09 - Mid Mounted Aerial Platform
e. Master drain valve
f. Electric dry type primer
g. Pump panel lights, 3 each side
h. Pump compartment light
i. OK to pump lights in cab and at pump panel
j . Engine cooler
k. Pump cooler
1. Two (2) 6" steamers, one on side panel
m. 2.5" left side gated suction
n. 1.5" tank fill
0. Two (2) 2" crosslay hose beds over the pump compartment
P. Two (2) 2-1/2" left side discharges
q. Two (2) 2-1/2"' right side discharges
r. Stainless steel schedule 40 piping with 10 year warranty
S. Panel gauge package: water tank level, tach, oil pressure, water temperature, voltmeter, light
and alarm system
t. Minimum 300 gallon polypropylene booster tank with lifetime warranty
V. 3" tank to pump connection
V. Minimum 10" x 8" fill tower with minimum 4" overflow tube
W. 15 ft. of soft suction hose sized for capacity of fire pump
7. APPARATUS BODY
a. Bidders to bid on each of their offered construction types:
• Extruded aluminum
• Formed aluminum
• Formed galvanneal steel
• Formed stainless steel
b. Bidders to state thicknesses, alloys and construction methods of all materials used in body
construction
C. Maximum number of left side compartments available
d. Maximum number of right side compartments available
e. Bidders to accurately state the total cubic footage of compartment space, along with each
compartment size
f. Lights in compartments to meet NFPA 1901 Chapter 13.10.5
g. Hose bed lighting must be provided per NFPA Chapter 1901 13.10.2
h. Back up alarm
i. Rear ladder storage for minimum 1 15'NFPA ground ladders fully enclosed at rear of apparatus,
ladders to be included
j . Rear pike pole storage for minimum of six (6) pike poles fully enclosed at rear of apparatus
k. Slide out pump operator platform
1. Hose bed with hose restraints to be NFPA quint compliant
m. Steps and handrails for climbing from ground to turntable - bidders to state exact design
n. Lights at each step
0. Stop/turn/back up lights
p. DOT clearance and marker lights
q. License plate light
r. Rear deck lights
S. Rub rail along each side of body
t. Running boards at each pump panel
U. Brushed stainless steel or black non -glare aluminum pump panels
TR 12430- Exhibit D
Base Specifications #09 -Mid Mounted Aerial Platform
8. EMERGENCY WARNING
a. NFPA Zone A lower and upper level lighting
b. NFPA Zone B / D lower level lighting
C. NFPA Zone C upper and lower level lighting
d. Electronic 200 watt siren/PA with minimum 100 watt speaker recessed in bumper
9. PAINT FINISH /REFLECTIVE STRIPING
a. Cab and body to be painted single tone with 10 year pro -rated paint and corrosion perforation
warranty
b. Wheels painted to match the cab and body
C. Reflective striping in accordance with Chapter 15.9.3
d. Reflective chevron on rear of apparatus in accordance with Chapter 15.9.3.2.
�0ri
a. 1 year bumper to bumper mechanical, excluding normal wear and tear items
b. 10 year cab and body structural
C. 10 year paint pro -rated
d. 10 year corrosion perforation on cab and body
e. 20 year aerial structural
f. Lifetime frame warranty
g. 2 year front axle
h. 2 year rear axle
i. 5 year fire pump
j . Lifetime booster tank
k. Manufacturer's standard 5 year warranty for transmission
TR 12430- Exhibit D
FLORIDA
ASSOCIATIOIN OF
COUNTIES
All About 141orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 MID MOUNTED AERIAL PLATFORM
Specification #09
(Extruded Aluminum Body -Aluminum Ladder)
The Mid Mounted Aerial Platform, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL: E-ONE HP 95 MM
BABE PRICE: $8491,613.00
MANUFACTURER: Hall -Mark Fire Apparatus (E-ONE)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a quint apparatus with a special emphasis on Chapters 1,
2, 39 4, 8, 129 13, 141, 159 169 18, 19, FMVSS (applicable areas) and NHTSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association,
of Counties have identified and equipped
items required to
vary from agency
by the purchaser
meet all current NFPA.
to agency, any
shall be made
the
additional
Florida Sheriffs Association and Florida Association
base unit with those specifications and equipment
Since equipment
needs and
preferences
are going to
options required
or changes
to the
base
unit desired
through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FI,ORIDA
A SSOCI NYMN Of
COUNTIES
AU About blorida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 MID MOUNTED AERIAL PLATFORM
Specification #09
(Extruded Aluminum Body - Steel Ladder)
The Mid Mounted Aerial Platform, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL:
BASE PRICE:
MANUFACTURER:
MODEL:
BASE PRICE:
MANUFACTURER:
Crimson MM 100'
$8549583,00
Crimson Fire (Public Safety...)
Spectr
$8449351.00
Ferrara Fire Apparatus, Inc.
Igniter XD
$8689463.00
Ferrara Fire Apparatus, Inc.
Spartan Gladiator
$7989554.00
Rosenbauer South Dakota, LLC
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a quint apparatus with a special emphasis on Chapters 1,
29 3, 49, 89 129 139 14, 15, 169 189 19, FMVSS (applicable areas) and NHTSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOC A IONN O
COUNTIES
All About Noreda
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 MID MOUNTED AERIAL PLATFORM
Specification #09
(Formed Aluminum Body - Steel Ladder)
The Mid Mounted Aerial Platform, purchased through this contract comes with all the standard
equipment as specified by . the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL: American LaFrance 100MMP
BASE PRICE: $8861,602.00
MANUFACTURER: American LaFrance, LLC
MODEL. Pierce Arrow XT Mid Mount
BASE PRICE: $8941,531.00
MANUFACTURER: Pierce Manufacturing, Inc.
KME Predator AerialCat FLO9100
$8301,497.00
Kovatch Mobile Equip. Corp. (KME)
Spartan Gladiator
$7809512.00
Rosenbauer South Dakota, LLC
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a quint apparatus with a special emphasis on Chapters 1,
21 31 4, 8, 12, 13, 149 159 16, 189 19, FMVSS (applicable areas) and NHTSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCL TION' OF
COLYNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 MID MOUNTED AERIAL PLATFORM
Specification #09
(Formed Stainless Steel Body - Aluminum Ladder)
The Mid Mounted Aerial Platform, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL:
BASE PRICE:
MANUFACTURER:
SPH 100
$9699128.00
Sutphen Corporation
SP110
$190149357.00
Sutphen Corporation
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a quint apparatus with a special emphasis on Chapters 1,
2, 39 49 8, 129 13, 149 15, 169 18, 19, FMVSS (applicable areas) and NHTSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCLATIOIN OF
COUNTIES
All About 141or°ida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 MID MOUNTED AERIAL PLATFORM
Specification #09
(Formed Stainless Steel Body - Steel Ladder)
The Mid Mounted Aerial Platform, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL:
BASE PRICE:
MANUFACTURER:
American LaFrance 100MMP
$8919503.00
American LaFrance, LLC
Crimson MM 100'
$8581,330.00
Crimson Fire (Public Safety...)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a quint apparatus with a special emphasis on Chapters 1,
2, 39 4, 89 12, 139 149 159, 169 189 19, FMVSS (applicable areas) and NHTSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION O
COLTNTIES
All About 141orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8t FLORIDA ASSOCIATION OF COUNTIES
Base Specifications*wns
SPECIFICATION # 10 -REAR MOUNTED
AERIAL PLATFORM
ALL ITEMS FACTORY INSTALLED UNLESS OTHERWISE INDICATED
THE CAB AND CHASSIS SHALL BE PROVIDED BY THE BODY MANUFACTURER
1. DOCUMENTATION, DELIVERY, TRAINING
a. When requested by end user, bidders to accurately state wheelbase, cab to axle, overall length,
bumper swing turn radius, curb -to -curb turning radius, overall height, overall width, GVWR,
angle of approach, angle of departure and SCAAN certification for drivetrain compatibility in
submitted specifications
b. Approval drawings provided prior to construction commencement
c. Two (2) sets of operator and service manuals
d. Delivery to be F.O.B. customer's location
e. Three (3) days of training by employee of manufacturer
f. Pump test certification by independent third party
g. Water tank capacity certification by independent third party
h. Aerial non-destructive, waterway flow test, performance and stability testing by independent
third party
i. 12 volt and, if applicable, 110 volt testing by independent third party
j . Vehicle weight, as measured by certified scales
2. CHASSIS
a. 110,000 psi heat treated steel frame rail with full length inner 110,000 psi C-channel liner
or integral torque box frame
b. 10 gauge polished stainless steel 16" to 24" extended front bumper with aluminum diamond
plate gravel shield
C. Tow hooks or eyes front and rear attached to the frame
d. 20,000 pound minimum front axle, suspension, tubeless radial tires, steel disc wheels
e. 50,000 pound minimum rear axle, suspension, tubeless radial tires, steel disc wheels
f. Front and rear mud flaps
g. NFPA 1901 Chapter 4.15.3 top speed rating requirement
TR 12430- Exhibit D
Base Speci, fications # 10 — Rear Mounted Aerial Platform
h. S-cam air brakes or equivalent, as large as possible, with automatic slack adjusters
i. Manufacturer's standard compressor
j . Minimum 5000 cubic inch air reservoir capacity
k. Air dryer, color coded air lines, turn drain valves on reservoirs
I. ABS brakes
m. Power steering with tilt/telescopic wheel
n. Vehicle data recorder "R) in compliance with Chapter 4.11 with required software meeting
4.11.8
0. Electronic Stability Control shall be provided in compliance with NFPA 1901 Chapter 4.13.1.2
if the manufacturer cannot comply with Chapters 4.13.1.1 through 4.13.1.1.3.2.
p. Tire pressure monitoring system with Chapter 4.13.4
3. POWERTRAIN
a. Minimum 450 horsepower turbocharged diesel engine with 1450 ft. lb. torque rating
b. Engine exhaust at front of right rear wheels
C. Secondary braking to meet NFPA
d. Engine manufacturer's statement of engine installation approval with approved cooling system
e. Drivelines to meet engine torque rating
f. Silicone coolant hoses with constant torque clamps
g. EVS 4000 automatic transmission
h. 50 gallon minimum fuel tank
i. OEM oil, fuel, transmission filters
4. CAB
a. Medium length tilt aluminum cab meeting NFPA 1901 Chapter 14.3.2
b. Seating for four, three in SCBA seats with SCBA brackets
c. Air ride driver seat, all others fixed position
d. All persons in 3-point seat belts per Chapter 14, seats equipped with seat belt/occupant
detection/warning system per Chapter 14
e. Electric over hydraulic cab tilt with manual back-up
f. Single tone cab paint finish with 10 year paint warranty pro -rated
g. Air conditioning and heating
h. Remote controlled mirrors (from driver's position) with separate flat and convex sections
i. DOT compliant headlights
j . Forward facing turn and warning lights
k. Cornering turn and warning lights
I. Minimum four (4) dome lights with red and clear bulbs
m. Minimum four (4) under cab step lights
n. Cab and compartment door ajar light and buzzer
o. One (1) engine compartment light
p. Color coded and function coded wiring
q. Alternator sized according to amp draw report
r. Minimum four (4) 750 CCA batteries
S. Load manager with automatic high idle function
t. Dual air horns with dual in -cab controls
5. AERIAL APPARATUS - ALUMINUM OR STEEL
a. Aerial shall meet or exceed all sections of NFPA 1901 Chapter 19
TR 12430- Exhibit D
Base Specifications # 1 O - Rear Mounted Aerial Platform
b. Ladder material: aluminum or steel
C. Rear -mounted configuration
d. Minimum 3-section aerial with minimum elevation of 100' per NFPA requirements
e. Rated horizontal reach per NFPA requirements
f. Rungs shall meet all aspects of NFPA 1901 19.2.5
g. Rungs equipped with a slip resistant surface meeting NFPA 1901 19.2.5
h. Rungs spacing meeting NFPA 1901 19.2.5
i. Turntable with pedestal mounted controls meeting NFPA 1901 19.4
j . Platform rated load capacity not flowing water: 1000 lbs. plus equipment
k. Platform rated load capacity while flowing 1000 gpm: 500 lbs. in addition to permanently
affixed equipment
1. Rated load capacities shall meet and /or exceed NFPA 1901 19.3
m. The aerial shall be rated in multiple configurations per Chapter 19.3.4
n. Extend/retract, rotate and hydraulic or electric over hydraulic controls meeting NFPA 1901
19.5 through 19.5.3.6.
0. Hydraulic pressure gauge at turntable controls
p. Illuminated Angle of Elevation Indicator meeting NFPA 1901 19.4.1 -
q. Flowmeter on turntable control pedestal meeting NFPA 1901 19.6.8
r. All aerial control devices shall meet NFPA 1901 19.17
S. Fall protection provisions shall be provided.
t. Bidders to state type of stabilizers and overall stabilizers spread
u. Aerial shall meet structural safety factors in accordance with NFPA 1901 19.20
V. Aerial shall meet NFPA 1901 stability safety factors Chapter 19.21
w. Lighted turntable area
X. The aerial manufacturer (the company that manufacturers the entire aerial device) shall
maintain a Quality Control Program in accordance with NFPA 1901 Chapter 19.22
y. Special attention shall be paid to meeting all safety requirements per NFPA 1901 19.20
Z. Aerial shall be fully tested and certified by third party certified testing company per NFPA
1901 19.24 and 19.25
aa. 2-way intercom system between ladder tip and turntable control pedestal.
bb. Minimum 1000 gpm waterway system meeting NFPA 1901 with remote control nozzle (controls
in platform and at turntable control pedestal) .
cc. Minimum 4" rear waterway inlet with pressure gauge and long handled chrome cap
dd. Minimum 4" waterway discharge with 4" valve with handwheel or electric control on pump
panel
ee. Waterway relief valve and minimum 1.5" drain at rear of apparatus
ff. Stabilizer controls and stabilizer to aerial controls mounted on rear of apparatus body
gg. One (1) high intensity spotlights on ladder tip
hh. Two high intensity flood lights on ladder base
ii. Painted finish on steel aerial -bidder shall provide copy of paint warranty on aerial
�l. Instruction plates and signs must be installed per NFPA 1901 Chapter 19.23
kk. Platform construction and design must meet NFPA 1901 Chapter 19.7.6
11. Platform operating positions must meet NFPA 1901 Chapter 19.9
6. FIRE PUMP & PLUMBING
a. Minimum 1500 GPM pump as rated per NFPA 1901 Chapter 16
b. Air operated pump shift
C. Discharge pressure relief valve
d. Intake pressure relief valve
e. Master drain valve
TR 12430- Exhibit D
Base Specifications # 1 O - Rear Mounted Aerial Platform
f. Electric dry type primer
g. Pump panel lights, 3 each side
h. Pump compartment light
i. OK to pump lights in cab and at pump panel
j . Engine cooler
k. Pump cooler
I. Two (2) 6" steamers, one on side panel
m. 2.5" left side gated suction
n. 1.5" tank fill
o. Two (2) 2" crosslay hose beds over the pump compartment
p. Two (2) 2-1/2" left side discharges
q. Two (2) 2-1/2" right side discharges
r. Stainless steel schedule 40 piping with 10 year warranty
S. Panel gauge package: water tank level, tach, oil pressure, water temperature, voltmeter, light
and alarm system
t. Minimum 300 gallon polypropylene booster tank with lifetime warranty
u. 3» tank to pump connection
V. Minimum 10" x 8" fill tower with minimum 4" overflow tube
W. 15 ft. of soft suction hose sized for capacity of fire pump
7. APPARATUS BODY
a. Bidders to bid on each of their offered construction types:
• Extruded aluminum
• Formed aluminum
• Formed galvanneal steel
• Formed stainless steel
b. Bidders to state thicknesses, alloys and construction methods of all materials used in body
construction
C. High left side compartments
d. High right side compartments
e. Bidders to accurately state the total cubic footage of compartment space, along with each
compartment size
f. Lights in compartments to meet NFPA 1901 Chapter 13.10.5
g. Hose bed lighting must be provided per NFPA Chapter 1901 13.10.2
h. Back up alarm
i. Rear ladder storage for minimum 11 5'NFPA ground ladders fully enclosed at rear of apparatus,
ladders to be included
j . Rear pike pole storage for minimum of six (6) pike poles fully enclosed at rear of apparatus
k. Slide out pump operator platform
1. Hose bed with hose restraints to be NFPA quint compliant
m. Steps and handrails for climbing from ground to turntable - bidders to state exact design
n. Lights at each step
o. Stop/turn/back up lights
p. DOT clearance and marker lights
q. License plate light
r. Rear deck lights
S. Rub rail along each side of body
t. Running boards at each pump panel
u. Brushed stainless steel or black non -glare aluminum pump panels
TR 12430- Exhibit D
Base Specifications # 1 O - Rear Mounted Aerial Platform
8. EMERGENCY WARNING
a. NFPA Zone A lower and upper level lighting
b. NFPA Zone B / D lower level lighting
C. NFPA Zone C upper and lower level lighting
d. Electronic 200 watt siren/PA with minimum
9. PAINT FINISH/REFLECTIVE STRIPING
100 watt speaker recessed in bumper
a. Cab and body to be painted single tone with 10 year pro -rated paint and corrosion perforation
warranty
b. Wheels painted to match the cab and body
C. Reflective striping in accordance with Chapter 15.9.3
d. Reflective chevron on rear of apparatus in accordance with Chapter 15.9.3.2.
a. 1 year bumper to bumper mechanical, excluding normal wear and tear items
b. 10 year cab and body structural
C. 10 year paint pro -rated
d. 10 year corrosion perforation on cab and body
e. 20 year aerial structural
f. Lifetime frame warranty
g. 2 year front axle
h. 2 year rear axle
i. 5 year fire pump
j . Lifetime booster tank
k. Manufacturer's standard 5 year warranty for transmission
TR 12430- Exhibit D
FLORIDA
AS,SOCIATION O
COUNTIES
All About 11orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 REAR MOUNTED AERIAL PLATFORM
Specification # 10
(Extruded Aluminum Body - Aluminum Ladder)
The Rear Mounted Aerial Platform, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL: E-ONE HP 100P
BASE PRICE: $8201,298.00
MANUFACTURER: Hall -Mark Fire Apparatus (E-ONE)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a quint apparatus with a special emphasis on Chapters 1,
29 39 4, 8, 129 13, 149 159 169, 189 19, FMVSS (applicable areas) and NHTSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATIOIN OF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 REAR MOUNTED AERIAL PLATFORM
Specification # 10
(Extruded Aluminum Body -Steel Ladder)
The Rear Mounted Aerial Platform, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL:
BASE PRICE:
MANUFACTURER:
MODEL:
BASE PRICE:
MANUFACTURER:
Crimson Star RM 100'
$7569389.00
Crimson Fire (Public Safety...)
Spectr
$7291,318.00
Ferrara Fire Apparatus, Inc.
Igniter XD
$7631430.00
Ferrara Fire Apparatus, Inc.
Spartan Gladiator
$7349810.00
Rosenbauer South Dakota, LLC
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a quint apparatus with a special emphasis on Chapters 1,
29 39 4, 89 129 139 14, 151, 16, 18, 19, FMVSS (applicable areas) and NHTSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASS()CL` rX.) 01"
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 REAR MOUNTED AERIAL PLATFORM
Specification # 10
(Formed Aluminum Body - Aluminum Ladder)
The Rear Mounted Aerial Platform, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL: Pierce Arrow XT Rear Mount PAP
BASE PRICE: $8501,581.00
MANUFACTURER: Pierce Manufacturing, Inc.
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a quint apparatus with a special emphasis on Chapters 1,
29 39 4, 8, 12, 139 14, 159 169 189 19, FMVSS (applicable areas) and NHTSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
V;SOCIATION' OF
COUNTIES
Att About .Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 REAR MOUNTED AERIAL PLATFORM
Specification # 10
(Formed Aluminum Body -Steel Ladder)
The Rear Mounted Aerial Platform, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSNs base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL:
BASE PRICE:
MANUFACTURER:
MODEL:
BASE PRICE:
MANUFACTURER.
American LaFrance 10ORMP
$7889974.00
American LaFrance, LLC
Pierce Arrow XT Rear Mount PAP
$7999259,00
Pierce Manufacturing, Inc.
KME Predator AerialCat FLO10102
$7919297.00
Kovatch Mobile Equip. Corp. (KME)
Spartan Gladiator
$7101,125,00
Rosenbauer South Dakota, LLC
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate. for a quint apparatus with a special emphasis on Chapters 1,
29 3, 49 89 129 139 149 159 169 18, 19, FMVSS (applicable areas) and NHTSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
.
FLORIDA
ASSOCLVIONKOF
COCJNTIES
All About 141orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 REAR MOUNTED AERIAL PLATFORM
Specification # 10
(Formed Stainless Steel Body -Steel Ladder)
The Rear Mounted Aerial Platform, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL: American LaFrance 100RMP Crimson Star RM 100'
BASE PRICE: $7929,399.00 $7601,631.00
MANUFACTURER: American LaFrance, LLC Crimson Fire (Public Safety...)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a quint apparatus with a special emphasis on Chapters 1,
29 31, 49, 8, 129 139 14, 159 161, 189 19, FMVSS (applicable areas) and NHTSA standards, we realize
equipment needs and preferences are going to vary from agency to agency. Any options required or
changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION, O
COUNTIES
Art About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
Base Specifications
SPECIFICATION # 11 -MEDIUM DUTY RESCUE.,
ALL ITEMS FACTORY INSTALLED UNLESS OTHERWISE INDICATED
FREIGHTLINER, INTERNATIONAL OR APPROVED EQUIVALENT
1. DOCUMENTATION, DELIVERY, TRAINING
AItATUS
a. When requested by end user, bidders to accurately state wheelbase, cab to axle, overall
length, overall height, overall width, GVWR, angle of approach, angle of departure
b. Approval drawings provided prior to construction commencement
C. Two (2) sets of operator and service manuals
d. Delivery to be F.O.B. customer's location
e. Vehicle orientation as outlined in NFPA 1901
f. 12 volt and, if applicable, 110 volt testing by independent third party
g. Vehicle weight, as measured by certified scales
2. COMMERCIAL 2-DOOR CHASSIS
a. Two wheel drive; minimum 108" cab to axle
b. 110,000 psi heat treated steel frame rail system
C. 12,000 pound minimum front axle, suspension, tubeless radial tires, steel disc wheels;
23,000 pound minimum rear axle, suspension, tubeless radial tires, steel disc wheels
d. Vehicle Data Recorder per Chapter 4.11 with required software
e. Electronic Stability Control shall be provided in compliance with NFPA 1901 Chapter 4.13.1.2
if the manufacturer cannot comply with Chapters 4.13.1.1 through 4.13.1.1.3.2.
f. Tire pressure monitoring system per Chapter 4.13.4
g. Chrome or stainless steel front bumper
h. Tow hooks or eyes front and rear attached to the frame
i. Front and rear mud flaps
j. S-cam air brakes or equivalent, as large as possible, with automatic slack adjusters
k. Minimum 13.2 cfm gear driven air compressor
1. Air dryer, turn drain valves on reservoirs
m. ABS brakes
n. Power steering with tilt/telescopic wheel, if available
I
TR 12430- Exhibit D
Base Specifications # 11 - Medium Duty Rescue Apparatus
3. POWERTRAIN
a. Minimum 330 horsepower turbocharged diesel engine
b. Engine exhaust at front of right rear wheels
C. Secondary engine braking
d. Drivelines to meet engine torque rating
e. Automatic transmission
f. 50 gallon minimum fuel tank
g. OEM oil, fuel, transmission filters
4. 2-DOOR CAB
a. Seating for three (3), seats with NFPA compliant seat belts and seat belt warning system
b. NFPA compliant 12-volt switches and instruments
C. Air conditioning and heating
d. Engine compartment light
e. Dome/step lights meeting NFPA 1901
f. Single tone cab paint finish with OEM standard paint warranty
g. Driver remote controlled mirrors with separate flat and convex sections
h. Dual type headlights
i. Forward facing turn and warning lights
j . Minimum two (2) under cab step lights
k. Cab and compartment door ajar light and buzzer
1. Engine compartment light
m. 270 amp alternator
n. Minimum two (2) 750 CCA batteries
o. Load manager with automatic high idle function
p. Dual air horns with dual in -cab controls
q. 110 volt battery charger receptacle near driver's door
5. APPARATUS BODY
a. Bidders to bid on each of their offered construction types:
• Extruded aluminum
• Formed aluminum
b. Minimum 15' body length (outside length, do not include rear step in 15' calculation of body
length) non -walk-in type
C. Body compartments shall be configured
• Two (2) transverse compartment(s) forward of rear wheels
• One (1) transverse compartment over rear axle each side
• One (1) full depth/full height compartment behind rear axle one each side
• One (1) full height x as deep as possible compartment on rear of body
d. Bidder to state compartment sizes
e. Minimum of 480 cubic feet of use able storage space
f. Compartment lights per NFPA Chapter 13.10.5
g. License plate light
h. One pair of 12-volt rear body upper scene lights per NFPA 1901
6. EMERGENCY WARNING
a. NFPA 1901 upper and lower warning light package
TR 12430- Exhibit D
Base Specifications # 11 - Medium Duty Rescue Apparatus
b. Electronic siren with siren speaker
7. PAINT FINISH
a. Cab OEM finish and body to be painted matching color
b. Single tone cab paint finish
C. Wheels painted to match the cab and body
d. NFPA 1901 required reflective stripe, on cab and body sides on cab door inner panels, chevron
stripe on rear of body
a. 1 year bumper to bumper mechanical, excluding normal wear and tear items
b. OEM chassis manufacturer's standard warranty
C. 10 year paint on body pro -rated
TR 12430- Exhibit D
FLORIDA
ASSOCIATION OF
COUNTIES
All About 141orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 FREIGHTLINER M2-106
Specification # 11
(Medium Duty Rescue Apparatus - 4g2)
The Freightliner M2-106, Medium Duty Rescue Apparatus, purchased through this contract comes
with all the standard equipment as specified by the manufacturer for this model and FSA's base
vehicle specification(s) requirements which are included and made a part of this contract's vehicle
base price as awarded by manufacturer by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
Crimson Star MR
$1581,867.00
Extruded Aluminum
Crimson Fire (Public Safety...)
E-ONE REHN
$1551,999.00
Extruded Aluminum
Hall -Mark Fire Apparatus (E-ONE)
Rescue Force FLS 11 FTLNR
$157,500.00
Extruded Aluminum
Wheeled Coach Industries, Inc.
FFA 108 MDR Rescue
$1639914.00
Extruded Aluminum
Ferrara Fire Apparatus, Inc.
FSA Rescue 11
$1781,200.00
Extruded Aluminum
Rosenbauer South Dakota, LLC
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a special service vehicle with a special emphasis on Chapters
1, 29 39 41 109 129 13, 14, 15, 25 (if applicable), FMVSS (applicable areas) and NHTSA standards,
we realize equipment needs and preferences are going to vary from agency to agency. Any options
required or changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION OF
COUNTIES
All About Nor°ida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 INTERNATIONAL DURA3TAR
Specification #11
(Medium Duty Rescue Apparatus - 4g2)
The International Durastar, Medium Duty Rescue Apparatus, purchased through this contract comes
with all the standard equipment as specified by the manufacturer for this model and FSA's base
vehicle specification(s) requirements which are included and made a part of this contract's vehicle
base price as awarded by manufacturer by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
Crimson Star MR
$1621,549.00
Extruded Aluminum
Crimson Fire (Public Safety...)
E-ONE REHN
$1609,899.00
Extruded Aluminum
Hall -Mark Fire Apparatus (E-ONE)
Rescue Force FLS 11INTL
$1679500.00
Extruded Aluminum
Wheeled Coach Industries, Inc.
FFA 108 MDR Rescue
$1621,379.00
Extruded Aluminum
Ferrara Fire Apparatus, Inc.
FSA Rescue 11
$17%018.00
Extruded Aluminum
Rosenbauer South Dakota, LLC
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a special service vehicle with a special emphasis on Chapters
19 21 39 4, 109 129 13, 14, 15, 25 (if applicable), FMVSS (applicable areas) and NHTSA standards,
we realize equipment needs and preferences are going to vary from agency to agency. Any options
required or changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430 Exhibit D
FI..ORIDA
SSOCIRFoK OF
Ct)UNTIES
All About 141orida
FLORIDA FIRE CHIEFS' ASSOCIATION.
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 FREIGHTLINER M2-106
Specification # 11
(Medium Duty Rescue Apparatus - 4x2)
The Freightliner M2-106, Medium Duty Rescue Apparatus, purchased through this contract comes
with all the standard equipment as specified by the manufacturer for this model and FSA's base
vehicle specification(s) requirements which are included and made a part of this contract's vehicle
base price as awarded by manufacturer by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
American LaFrance
$1709316.00
Formed Aluminum
American LaFrance,
16' W/AR
LLC
Pierce MDR
$1659411.00
Formed Aluminum
Pierce Manufacturing, Inc.
Toyne Medium Rescue
$1989,600.00
Formed Aluminum
Toyne, Inc. (Southeastern...)
KME FLIIMDR
$1691,404.00
Formed Aluminum
Kovatch Mobile Equip.
Corp. (KME)
FSA Rescue 11
$1549442.00
Formed Aluminum
Rosenbauer South Dakota, LLC
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a special service vehicle with a special emphasis on Chapters
19 2, 39 49 10, 12, 13, 14, 15, 25 (if applicable), FAWSS (applicable areas) and NHTSA standards,
we realize equipment needs and preferences are going to vary from agency to agency. Any options
required or changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION € F
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 INTERNATIONAL DURASTAR
Specification # 11
(Medium Duty Rescue Apparatus - 4g2)
The International Durastar, Medium Duty Rescue Apparatus, purchased through this contract comes
with all the standard equipment as specified by the manufacturer for this model and FSKs base
vehicle specification(s) requirements which are included and made a part of this contract's vehicle
base price as awarded by manufacturer by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
American I.aFrance
$1769390,00
Formed Aluminum
American LaFrance,
169 W/AR
LLC
Pierce MDR
$1749065.00
Formed Aluminum
Pierce Manufacturing, Inc.
Sutphen CR Series
$2581,980.00
Formed Aluminum
Sutphen Corporation
KME FLI 1MDR
$1659607.00
Formed Aluminum
Kovatch Mobile Equip.
FSA Rescue 11
$1551,259.00
Formed Aluminum
Rosenbauer South
Corp. (KME)
Dakota, LLC
Rescue Toyne Medium Rescue
$2049300.00
Formed Aluminum
Toyne, Inc. (Southeastern...)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a special service vehicle with a special emphasis on Chapters
11 2, 39 49 109 129 139 14, 15, 25 (if applicable), FMVSS (applicable areas) and NHTSA standards,
we realize equipment needs and preferences are going to vary from agency to agency. Any options
required or changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
COUNTIES
All About 141orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
SL FLORIDA ASSOCIATION OF COUNTIES
Base Specifications
SPECIFICATION # 12 -HEAVY RESCUE APPARATUS
ALL ITEMS FACTORY INSTALLED UNLESS OTHERWISE INDICATED
THE CAB AND CHASSIS SHALL BE PROVIDED BY THE BODY MANUFACTURER
1. DOCUMENTATION, DELIVERY, TRAINING
a. When requested by end user, bidders to accurately state wheelbase, cab to axle, overall length,
bumper swing turn radius, curb -to -curb turning radius, overall height, overall width, GVWR,
angle of approach, angle of departure and SCAAN certification for drivetrain compatibility in
submitted specifications
b. Approval drawings provided prior to construction commencement
C. Two (2) sets of operator and service manuals
d. Delivery to be F.O.B. customer's location
e. Vehicle orientation as outlined in NFPA 1901
f. Pump test certification (if applicable) by independent third party
g. Water tank capacity (if applicable) certification
h. 12 volt and, if applicable, 110 volt testing by independent third party
i. Vehicle weight, as measured by certified scales
2. CHASSIS
a. 110, 000 psi heat treated steel frame rail with full length inner 110, 000 psi C-channel liner
b. 10 gauge polished stainless steel 16" to 24" extended front bumper with aluminum diamond
plate gravel shield
c. Tow hooks or eyes front and rear attached to the frame
d. 18,000 pound minimum front axle, suspension, tubeless radial tires, steel disc wheels
e. 24,000 pound minimum rear axle, suspension, tubeless radial tires, steel disc wheels
f. Front and rear mud flaps
g. NFPA 1901 Chapter 4.15.3 top speed rating requirement
h. S-cam air brakes, as large as possible, with automatic slack adjusters
i. Manufacturer's standard compressor
j . Minimum 5000 cubic inch air reservoir capacity
k. Air dryer, color coded air lines, turn drain valves on reservoirs
TR 12430- Exhibit D
Base Specifications # 12 - Heavy Rescue Apparatus
1. ABS brakes
m. Power steering with tilt/telescopic wheel
n. Vehicle data recorder (VDR) in compliance with Chapter 4.11 with required software meeting
4.11.8
0. Electronic Stability Control shall be provided in compliance with NFPA 1901 Chapter 4.13.1.2
if the manufacturer cannot comply with Chapters 4.13.1.1 through 4.13.1.1.3.2, or model
to have been tilt table tested and certified per Chapter 4.13.1.1.1
p. Tire pressure monitoring system with Chapter 4.13.4
3. POWERTRAIN
a. Minimum 350 horsepower turbocharged diesel engine with 1000 ft. lb. torque rating
b. Minimum EVS 3000 transmission
C. Engine exhaust at front of right rear wheels
d. Secondary braking to meet NFPA
e. Engine manufacturer's statement of engine installation approval with approved cooling system
f. Drivelines to meet engine torque rating
g. Silicone coolant hoses with constant torque clamps
h. 50 gallon minimum fuel tank
i. OEM oil, fuel, transmission filters
4. CAB
a. Medium length tilt aluminum cab meeting NFPA 1901 Chapter 14.3.2
b. Seating for four, three in SCBA seats with SCBA brackets
C. Air ride driver seat, all others fixed position
d. All persons in 3-point seat belts per Chapter 14, seats equipped with seat belt/occupant
detection/warning system per Chapter 14
e. Electric over hydraulic cab tilt with manual back-up
f. Single tone cab paint finish with 10 year paint warranty pro -rated
g. Air conditioning and heating
h. Remote controlled mirrors (from driver's position) with separate flat and convex sections
i. DOT compliant headlights
j . Forward facing turn and warning lights
k. Cornering turn and warning lights
1. Minimum four (4) dome lights with red and clear bulbs
m. Minimum four (4) under cab step lights
n. Cab and compartment .door ajar light and buzzer
0. One (1) engine compartment light
p. Color coded and function coded wiring
q. Alternator sized according to amp draw report
r. Minimum four (4) 750 CCA batteries
S. Load manager with automatic high idle function
t. Dual air horns with dual in -cab controls
5. APPARATUS BODY
a. Bidders to bid on each of their offered construction types:
• Extruded aluminum
• Formed aluminum
TR 12430- Exhibit D
Base Specifications # 12 - Heavy Rescue Apparatus
Lei
7.
b. Minimum 18' body length (outside body length, do not include rear step in 18' body length
calculation) non -walk-in type body
C. Body compartments shall be configured
• Two (2) transverse compartment(s) forward of rear wheels
• One (1) transverse compartment over rear axle each side
• One (1) full depth/full height compartment behind rear axle one each side
• One (1) full height x as deep as possible compartment on rear of body
d. Bidder to state compartment sizes
e. Minimum of 520 cubic feet of use able storage space
f. Compartment lights per NFPA Chapter 13.10.5
g. License plate light
h. One pair of 12-volt rear body upper scene lights per NFPA 1901
i. Two (2) 12-volt upper side body scene lights per side (4 lights total)
j . Minimum 10" rear step for access for rear storage compartment, step surface to meet NFPA
1901 requirements for slip -resistance, with NFPA compliant handrails
EMERGENCY WARNING
a. NFPA Zone A lower and upper level lighting
b. NFPA Zone B / D lower level lighting
C. NFPA Zone C upper and lower level lighting
d. Electronic 200 watt siren/PA with minimum
PAINT FINISH
100 watt speaker recessed in bumper
a. Cab and body to be painted single tone
b. Wheels. painted to match the cab and body
C. Minimum 4" reflective stripe on cab and body,
1901
chevron striping on rear of body per NFPA
a. 1 year bumper to bumper mechanical, excluding normal wear and tear items
b. 10 year cab and body structural
C. 10 year paint pro -rated
d. 10 year corrosion perforation on cab and body
e. Lifetime frame warranty
f. Manufacturer's standard warranty for front and rear axle
g. 5 year engine
h. Manufacturer's standard 5 year warranty for transmission
i. 2 year fire pump (if applicable)
j . Lifetime booster tank (if applicable)
TR 12430- Exhibit D
FEORIDA
ASSOCIATION OF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 HEAVY RESCUE APPARATUS
Specification # 12
(Extruded Aluminum Body)
The Heavy Rescue Apparatus, purchased through this contract comes with all the standard equipment
as specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL:
BASE PRICE:
N[ANUFACTURER:
MODEL:
BASE PRICE:
MANUFACTURER:
MODEL:
BASE PRICE:
MANUFACTURER:
Crimson Star HR
$2379303.00
Crimson Fire (Public Safety...)
Intruder MFDXL
$2359984.00
Ferrara Fire Apparatus, Inc.
Spartan Force
$2471,658.00
Rosenbauer South Dakota, LLC
Igniter XD XMFD
$2711,243.00
Ferrara Fire Apparatus, Inc.
E-ONE REHN Typhoon
$2449925.00
Hall -Mark Fire Apparatus (E-ONE)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a special service vehicle with a special emphasis on Chapters
1, 29 3, 4, 109 12, 13, 14, 15, 25 (if applicable), FMVSS (applicable areas) and NHTSA standards,
we realize equipment needs and preferences are going to vary from agency to agency. Any options
required or changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATIONOF
COUNTIES
AU About 141orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 HEAVY RESCUE APPARATUS
Specification # 12
(Formed Aluminum Body)
The Heavy Rescue Apparatus, purchased through this contract comes with all the standard equipment
as specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL: American LaFrance 18' W/ACR
BASE PRICE: $2731,887.00
MANUFACTURER: American LaFrance, LLC
MODEL: Pierce Saber HDR
BASE PRICE: $2721,561.00
MANUFACTURER: Pierce Manufacturing, Inc.
MODEL: Sutphen R Series
BASE PRICE: $3551,247.00
MANUFACTURER: Sutphen Corporation
KME Predator FL 12HDR
$2671,534.00
Kovatch Mobile Equip. Corp. (KME)
Spartan Force
$2299727.00
Rosenbauer South Dakota, LLC
Spartan Heavy Rescue
$2741,000.00
Toyne, Inc. (Southeastern...)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition)
and all chapters that are appropriate for a special service vehicle with a special emphasis on Chapters
19 21 31 4, 10, 129 13, 14, 15, 25 (if applicable), FEWSS (applicable areas) and NI -VISA standards,
we realize equipment needs and preferences are going to vary from agency to agency. Any options
required or changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCI TIO OT"
COL NTIES
AU About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
iPECIFI
Base Specifications
TION # 13 - 251
N MOBILE
WATER SUPPLY FIRE APPARATUS
ALL ITEMS FACTORY INSTALLED UNLESS OTHERWISE INDICATED
FREIGHTLINER, INTERNATIONAL OR APPROVED EQUIVALENT
1. DOCUMENTATION, DELIVERY, TRAINING
a, When requested by end user, bidders to accurately state wheelbase, cab to axle, overall
length, bumper swing turn radius, curb -to -curb turning radius, overall height, overall width,
GVWR, angle of approach, angle of departure in submitted specifications
b. Approval drawings provided prior to construction commencement
c. Two (2) sets of operator and service manuals
d. Delivery to be F.O.B. customer's location
e. Pump test certification by independent third party
f. Water tank capacity certification
g. 12 volt and, if applicable, 110 volt testing by independent third party
h. Vehicle weight, as measured by certified scales
2. COMMERCIAL 2-DOOR CHASSS
a. Two wheel drive
b. Upgraded electrical system for emergency vehicle use to include a minimum of two batteries,
minimum alternator(s) output of 220 amps.
C. 110,000 psi heat treated steel frame with full length inner C-channel liner
d. 16, 000 pound minimum front axle, suspension, tubeless radial tires, steel disc wheels; 44, 000
pound minimum rear tandem axle, suspension, tubeless radial tires, steel disc wheels
e. Vehicle Data Recorder per Chapter 4.11 with required software
f. Electronic Stability Control shall be provided in compliance with NFPA 1901 Chapter 4.13.1.2
if the manufacturer cannot comply with Chapters 4.13.1.1 through 4.13.1.1.3.2.
g. Tire pressure monitoring system per Chapter 4.13.4
h. Chrome or stainless steel front bumper
i. Tow hooks or eyes front and rear attached to the frame
j . Front and rear mud flaps
TR 12430- Exhibit D
.Base Specifications #13 - 2500 Gallon Mobile Water Supply Fire Apparatus
k. S-cam air brakes, as large as possible, with automatic slack adjusters
1. Minimum 13.2 cfm gear driven air compressor
m. Air dryer, turn drain valves on reservoirs
n. ABS brakes
0. Power steering with tilt/telescopic wheel, if available
3. POWERTRAIN
a. Minimum 330 horsepower turbocharged diesel engine
b. Engine exhaust at front of right rear wheels
C. Secondary engine braking to meet NFPA
d. Drivelines to meet engine torque rating
e. Automatic transmission
f. 50 gallon minimum fuel tank
g. OEM oil, fuel, transmission filters
4. 2-DOOR CAB
a. Seating for two (2) - bucket style vinyl seats with NFPA compliant seat belts and seat belt
warning system
b. NFPA compliant 12-volt switches and instruments
c. Air conditioning and heating
d. Engine compartment light
e. Dome/step lights meeting NFPA 1901
f. Single tone cab paint finish with OEM standard paint warranty
g. Driver remote controlled mirrors with separate flat and convex sections
h. Dual type headlights
i. Forward facing turn and warning lights
j . Minimum two (2) under cab step lights
k. Cab and compartment door ajar light and buzzer
1. Engine compartment light
m. 270 amp alternator
n. Minimum two (2) 750 CCA batteries
0. Load manager with automatic high idle function
p. Dual air horns with dual in -cab controls
q. 110 volt battery charger receptacle near driver's door
5. FIRE PUMP & PLUMBING
a. Minimum 500 gpm midship mounted PTO pump per NFPA 1901
b. Discharge pressure relief valve
c.. Intake pressure relief valve
d. Master drain valve
e. Electric dry type primer
f. Pump panel lights, 3 each side
g. Pump compartment light
h. OK to pump lights in cab and at pump panel
i. Engine cooler
j . Pump cooler
k. One (1) 4. 5" minimum steamer, on left side panel
1. 2.5" left side gated suction
Chapter 16
TR 12430- Exhibit D
Base Specifications # 13 - 2500 Gallon Mobile Water Supply Fire Apparatus
m. 2-1 /2" tank fill pump to tank fill
n. Two 2.5" direct gated external tank fills
o. Two 2" crosslay hose beds over the pump compartment
p. One 2.5" left side discharge
q. One 2.5" right side discharge
r. Stainless steel piping with 10 year warranty
S. Panel gauge package: water tank level, tach, oil pressure, water temperature, voltmeter, light
and alarm system
t. Side mount pump panel with gauges and all pump controls on driver side pump panel
u. 2500 gallon polypropylene booster tank with lifetime warranty
V. 3" tank to pump connection
w. Minimum 10" x 8" fill tower with minimum 4" overflow tube
X. 10" Square tank dump valve with manual control with 3-way
dump capability
6. APPARATUS BODY
a. Bidders to bid on each of their offered construction types:
• Extruded aluminum
• Formed aluminum
• Formed galvanneal steel
• Formed stainless steel
b. Bidders to state thicknesses, alloys and construction methods of all materials used in body
construction
C. Hard suction rack for two (2) lengths 10" x 4.5" minimum of hard suction
d. Compartments: low side compartments both sides of body forward of and behind rear wheels;
bidders to accurately state the total cubic footage of compartment space, along with each
compartment size
e. Lights in compartments to meet NFPA 1901 Chapter 13.10.5
f. Back up alarm
g. Hose bed with hose restraints to be NFPA compliant; including one (1) adjustable divider
h. Steps and handrails for climbing from ground to hose bed - bidders to state exact design
i. Lights at each step
j. Stop/turn/back up lights
k. DOT clearance and marker lights
1. License plate light
m. Rear deck lights
n. Rub rail along each side of body and rear of body
o. Running boards at each pump panel
p. Brushed stainless steel or black non -glare aluminum pump panels
q. Hose bed lighting must be provided per NFPA 1901 Chapter 13.10.2
7. EMERGENCY WARNING
a. NFPA Zone A lower and upper level lighting
b. NFPA Zone B / D lower level lighting
C. NFPA Zone C upper and lower level lighting
d. Electronic 200 watt siren/PA with minimum
100 watt speaker recessed in bumper
TR 12430- Exhibit D
Base Specifications # 13 - 2500 Gallon Mobile Water Supply Fire Apparatus
8. PAINT FINISH
a. Body to be painted single tone with 10 year pro -rated paint and corrosion perforation warranty
b. Wheels painted to match the cab and body
c. Cab paint to be covered by cab manufacturer's paint warranty
a. 1 year bumper to bumper mechanical, excluding normal wear and tear items
b. 10 year body structural
C. 10 year paint pro -rated on body
d. 10 year corrosion perforation on body
e. OEM Chassis manufacturer's standard warranty
f. 5 year fire pump warranty
g. Lifetime warranty on water tank
TR 12430- Exhibit D
F�.LS`OR.I`DAF
COUNTIES
All About Plorida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 FREIGHTLINER M2-106
Specification # 13
(2500 Gallon Mobile Water Supply Fire Apparatus)
The Freightliner M2-106, 2500 Gallon Mobile Water Supply Fire Apparatus, purchased through this
contract comes with all the standard equipment as specified by the manufacturer for this model and
FSA's base vehicle specification(s) requirements which are included and made a part of this contract's
vehicle base price as awarded by manufacturer by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
Crimson Star Tanker
$2121,368.00
Extruded Aluminum
Crimson Fire (Public Safety... )
E-ONE TTSA
$2079330.00
Extruded Aluminum
Hall -Mark Fire Apparatus (E-ONE)
FFA T2500 Tanker
$2499330.00
Extruded Aluminum
Ferrara Fire Apparatus, Inc.
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for mobile water supply Chapter 7, FMVSS (applicable areas) and NHTSA standards, we
realize equipment needs and preferences are going to vary from agency to agency. Any options required
or changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FEORIDA
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 INTERNATIONAL WORKSTAR
Specification # 13
(2500 Gallon Mobile Water Supply Fire Apparatus)
The International Workstar, 2500 Gallon Mobile Water Supply Fire Apparatus, purchased through
this contract comes with all the standard equipment as specified by the manufacturer for this model
and FSA's base vehicle specifications) requirements which are included and made a part of this
contract's vehicle base price as awarded by manufacturer by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
Crimson Star Tanker
$211, 764.00
Extruded Aluminum
Crimson Fire (Public Safety...)
E-ONE TTSA
$2109127.00
Extruded Aluminum
Hall -Mark Fire Apparatus (E-ONE)
FFA T2500 Tanker
$2479484.00
Extruded Aluminum
Ferrara Fire Apparatus, Inc.
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for mobile water supply Chapter 7, FMVSS (applicable areas) and NHTSA standards, we
realize equipment needs and preferences are going to vary from agency to agency. Any options required
or changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION OF
COUNTIES
All About 141orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 FREIGHTLINER M2-106
Specification # 13
(2500 Gallon Mobile Water Supply Fire Apparatus)
The Freightliner M2-106, 2500 Gallon Mobile Water Supply Fire Apparatus, purchased through this
contract comes with all the standard equipment as specified by the manufacturer for this model and
FSA's base vehicle specification(s) requirements which are included and made a part of this contract's
vehicle base price as awarded by manufacturer by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
American LaFrance T/A Tanker KME Flatback FL132500
$2551,828.00 $236,125.00
Formed Aluminum Formed Aluminum
American LaFrance, LLC Kovatch Mobile Equip. Corp. (KME)
Pierce Contender Series
$2061,391.00
Formed Aluminum
Pierce Manufacturing, Inc.
Toyne FFCSA 2500
$233,500.00
Formed Aluminum
Toyne, Inc. (Southeastern...)
FSA Tanker 13
$2039365.00
Formed Aluminum
Rosenbauer South
Dakota, LLC
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for mobile water supply Chapter 7, FWSS (applicable areas) and NHTSA standards, we
realize equipment needs and preferences are going to vary from agency to agency. Any options required
or changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOC ATIO O
COUNTIES
All About 141orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 INTERNATIONAL WORKSTAR
Specification # 13
(2500 Gallon Mobile Water Supply Fire Apparatus)
The International Workstar, 2500 Gallon Mobile Water Supply Fire Apparatus, purchased through
this contract comes with all the standard equipment as specified by the manufacturer for this model
and FSA's base vehicle specification(s) requirements which are included and made a part of this
contract's vehicle base price as awarded by manufacturer by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
American LaFrance
$2809281.00
Formed Aluminum
American LaFrance,
T/A Tanker KME Flatback FL132500
$2319803.00
Formed Aluminum
LLC Kovatch Mobile Equip. Corp. (KME)
Pierce Contender Series
$2111,598.00
Formed Aluminum
Pierce Manufacturing, Inc.
Toyne FFCSA 2500
$2371,250.00
Formed Aluminum
Toyne, Inc. (Southeastern...)
FSA Tanker 13
$2079103,00
Formed Aluminum
Rosenbauer South
Dakota, LLC
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for mobile water supply Chapter 7, FMVSS (applicable areas) and NHTSA standards, we
realize equipment needs and preferences are going to vary from agency to agency. Any options required
or changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION O
COUNTIES
All About Iblorida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 FREIGHTLINER M2-106
Specification # 13
(2500 Gallon Mobile Water Supply Fire Apparatus)
The Freightliner M2-106, 2500 Gallon Mobile Water Supply Fire Apparatus, purchased through this
contract comes with all the standard equipment as specified by the manufacturer for this model and
FSA's base vehicle specification(s) requirements which are included and made a part of this contract's
vehicle base price as awarded by manufacturer by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
KME Flatback FL132500
$227,000.00
Formed Gavanneal Steel
Kovatch Mobile Equip. Corp. (KME)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for mobile water supply Chapter 7, FMVSS (applicable areas) and NHTSA standards, we
realize equipment needs and preferences are going to vary from agency to agency. Any options required
or changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the e
unit only. The Florida Fire Chiefs'
of Counties have identified and e
items
required to meet all currer
vary from agency
by the purchaser
to agency, any
shall be made
Bove referenced vehicle specification comes equipped as a base
Association, Florida Sheriffs Association and Florida Association
tuipped the base unit with those specifications and equipment
t NFPA. Since equipment needs and preferences are going to
additional options required or changes to the base unit desired
through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
F(�EOR�g.IDAHAIN F
COLYN L IES
All About blorida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 INTERNATIONAL WORKSTAR
Specification # 13
(2500 Gallon Mobile Water Supply Fire Apparatus)
The International Workstar, 2500 Gallon Mobile Water Supply Fire Apparatus, purchased through
this contract comes with all the standard equipment as specified by the manufacturer for this model
and FSA's base vehicle specification(s) requirements which are included and made a part of this
contract's vehicle base price as awarded by manufacturer by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
KME Flatback FL 132500
$222, 681.00
Formed Gavanneal Steel
Kovatch Mobile Equip. Corp. (KME)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for mobile water supply Chapter 7, FMVSS (applicable areas) and NHTSA standards, we
realize equipment needs and preferences are going to vary from agency to agency. Any options required
or changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FILORIDA
ASSO IATIO OF
COUNTIES
All About 11orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 FREIGHTLINER M2-106
Specification # 13
(2500 Gallon Mobile Water Supply Fire Apparatus)
The Freightliner M2-106, 2500 Gallon Mobile Water Supply Fire Apparatus, purchased through this
contract comes with all the standard equipment as specified by the manufacturer for this model and
FSA's base vehicle specification(s) requirements which are included and made a part of this contract's
vehicle base price as awarded by manufacturer by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
Crimson Star Tanker
$2179103.00
Formed Stainless Steel
Crimson Fire (Public Safety...)
Toyne FFCSA-2500
$2409200.00
Formed Stainless Steel
Toyne, Inc. (Southeastern...)
KME Flatback FL 132500
$2439952.00
Formed Stainless Steel
Kovatch Mobile Equip. Corp. (KME)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for mobile water supply Chapter 7, FMVSS (applicable areas) and NHTSA standards, we
realize equipment needs and preferences are going to vary from agency to agency. Any options required
or changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA.
ASSOCIATION OF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 INTERNATIONAL WORKSTAR
Specification # 13
(2500 Gallon Mobile Water Supply Fire Apparatus)
The International Workstar, 2500 Gallon Mobile Water Supply Fire Apparatus, purchased through
this contract comes with all the standard equipment as specified by the .manufacturer for this model
and FSNs base vehicle specification(s) requirements which are included and made a part of this
contract's vehicle base price as awarded by manufacturer by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
Crimson Star Tanker
$214,970.00
Formed Stainless Steel
Crimson Fire (Public Safety...)
Sutphen CTS-2500 Tanker
$283,629.00
Formed Stainless Steel
Sutphen Cororation
KME Flatback FL 132500
$2391636.00
Formed Stainless Steel
Kovatch Mobile Equip. Corp. (KME)
Toyne FFCSA-2500
$2469500.00
Formed Stainless Steel
Toyne, Inc. (Southeastern...)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for mobile water supply Chapter 7, FMVSS (applicable areas) and NH'I'SA standards, we
realize equipment needs and preferences are going to vary from agency to agency. Any options required
or changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
<4015SO I ATIO OF;
COUNTIES
All About 141orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
Base Specifications*wns
SPECIFICATION # 14 - WILDLAND FIRE APPARATUS
ALL ITEMS FACTORY INSTALLED UNLESS OTHERWISE INDICATED
FORD, DODGE, INTERNATIONAL OR APPROVED EQUIVALENT
1. DOCUMENTATION, DELIVERY, TRAINING
a. When requested by end user, bidders to accurately state wheelbase, cab to axle, overall
length, bumper swing turn radius, curb -to -curb turning radius, overall height, overall width,
GVWR, angle of approach, angle of departure in submitted specification
b. Approval drawings provided prior to construction commencement
C. Two (2) sets of operator and service manuals
d. Delivery to be F.O.B. customer's location
e. Vehicle weight measured by certified scale
2. COMMERCIAL 2-DOOR CHASSIS
a. Cab to axle - 60"
b. GVWR - 19,000 lbs -
c. Heavy service suspension
d. Turbo diesel engine with heavy duty cooling
e. Manufacturer's standard front and rear axles
f. Power steering
g. Tires - all season with steel wheels
h. Alternator(s) meeting 12-volt system requirements
i. Battery system to meet 12-volt system requirements
j . Fuel tank - minimum 40 gallon
k. Front tow hooks
3. POWER TRAIN
a. Diesel engine
b. Automatic transmission
C. OEM fuel tank, largest available
TR 12430- Exhibit D
Base Specifications cations # 14 - Wildland Fire Apparatus
d. Limited slip differential, if available as standard equipment
4. 2-DOOR CAB
a. Seating for three (3) - full width vinyl bench seat
b. Single tone cab paint finish with OEM standard paint warranty
C. Air conditioning and heating
d. Mirrors with separate flat and convex sections - extended trailer towing mirrors
e. Dual type headlights
f. Forward facing turn and warning lights
g. Minimum two (2) under cab step lights
h. Engine compartment light
i. Slip resistant running boards under cab doors per NFPA 1906
5. FIRE PUMP & PLUMBING
a. Minimum 18 HP gasoline engine driven pump (NFPA 1906) with electric start capable of 150
gpm @ 100 psi
b. Primer
C. Lighted pump control panel
d. Throttle
e. Pump cooler or recirculation line
f. 2-1/2 91) suction gated for drafting
g. 1" tank fill
h. One 1-1/2" discharge
i. One 1" discharge
j . Gauge package: Sight type water tank level in booster tank, single master pressure gauge
k. 300 gallon skid type polypropylene booster tank with lifetime warranty
1. 2 1 /2" tank to pump connection
m. Minimum 8" square fill tower with minimum 4" overflow tube
n. Electric rewind hose reel with 1 50 ft. of 1" red rubber booster hose
6. APPARATUS BODY
a. Extruded aluminum all welded body with bolt on modular aluminum diamond plate
compartments, two (2) per side
b. Bidders to state thickness, alloys and construction methods of all materials used in body
construction
C. Bidders to accurately state the total cubic footage of compartment space, along with each
compartment size
d. One (1) light in each compartment
e. Backup alarm
f. Stirrup type step for climbing from ground to flat bed - bidders to state exact design
g. Lights at each step
h. Stop/turn/backup lights
i. DOT clearance and marker lights
j . License plate light
k. Rear deck lights
1. No wood used in mounting
TR 12430- Exhibit D
Base Specifications # 14 - Wildland Fire Apparatus
7. EMERGENCY WARNING
a. Fully compliant with NFPA 1906, Wildland Fire Apparatus
b. Electronic 200 watt siren/PA with minimum 100 watt speaker
8. PAINT FINISH
a. Apparatus body left unpainted
a. One (1) year bumper to bumper mechanical, excluding normal wear and and tear items
b. OEM Chassis manufacturer's standard warranty
TR 12430- Exhibit D
FLORIDA.
ASSOCIATION OF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 FORD F-550
Specification # 14
(Wildland Fire Apparatus)
The Ford F-550, Wildland Fire Apparatus, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSNs base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL: Wildland Brush
BASE PRICE: $859970.00
MANUFACTURER: American LaFrance, LLC
MODEL:
BASE PRICE:
MANUFACTURER:
MODEL:
BASE PRICE:
MANUFACTURER:
Wildland
$849586.00
Hall -Mark Fire Apparatus (E-ONE)
Pierce F550 Wildland
$88,067.00
Pierce Manufacturing, Inc.
Wildland Brush
$99,060.00
Ferrara Fire Apparatus, Inc.
KME Wildland FL 14WFA
$100, 597.00
Kovatch Mobile Equip. Corp. (KME)
Wildland Brush
$931,300.00
Toyne, Inc. (Southeastern...)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1906, FMVSS
(applicable areas) and NHTSA standards, we realize equipment needs and preferences are going to
vary from agency to agency. Any options required or changes required by purchaser shall be made
through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 DODGE RAM 5500
Specification # 14
(Wildland Fire Apparatus)
The Dodge Ram 5500, Wildland Fire Apparatus, purchased through this contract comes with all
the standard equipment as specified by the manufacturer for this model and FSA's base vehicle
specification(s) requirements which are included and made a part of this contract's vehicle base price
as awarded by manufacturer by specification.
MODEL:
BASE PRICE:
NL424LTFACTURERO
MODEL.
BABE PRICE:
MANUFACTURER:
Wildland Brush
$899020.00
American LaFrance, LLC
Wildland
$859661.00
Hall -Mark Fire Apparatus (E-ONE)
Wildland Brush
$1021,589.00
Ferrara Fire Apparatus, Inc.
KME Wildland FLI4WFA
$100,071.00
Kovatch Mobile Equip. Corp. (KME)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1906, FMVSS
(applicable areas) and NHTSA standards, we realize equipment needs and preferences are going to
vary from agency to agency. Any options required or changes required by purchaser shall be made
through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION OF
All About Floridd
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 INTERNATIONAL DURASTAR 4300M7
Specification # 14
(Wildland Fire Apparatus)
The International Durastar 4300M7, Wildland Fire Apparatus, purchased through this contract
comes with all the standard equipment as specified by the manufacturer for this model and FSA's
base vehicle specification(s) requirements which are included and made a part of this contract's
vehicle base price as awarded by manufacturer by specification.
MODEL:
BASE PRICE:
MANUFACTURER:
MODEL:
BASE PRICE:
MANUFACTURER:
Wildland Brush
$95,594.00
American LaFrance, LLC
Wildland Brush
$1341,700.00
Toyne, Inc. (Southeastern...)
KME Wildland FL 14WFA
$1311,480.00
Kovatch Mobile Equip. Corp. (KME)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1906, FMVSS
(applicable areas) and NHTSA standards, we realize equipment needs and preferences are going to
vary from agency to agency. Any options required or changes required by purchaser shall be made
through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION OF
COOTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
Base Specifications
;IFICATION # 15 -
OMMERCML
ALL ITEMS FACTORY INSTALLED UNLESS OTHERWISE INDICATED
FREIGHTLINER, INTERNATIONAL OR APPROVED EQUIVALENT
1. COMMERCIAL 2-DOOR CHASSIS
a. Two wheel drive
b. 110,000 psi heat treated steel frame rail system
C. 12,000 pound minimum front axle, suspension, tubeless radial tires, steel disc wheels;
23,000 pound minimum rear axle, suspension, tubeless radial tires, steel disc wheels
d. Vehicle Data Recorder per Chapter 4.11 with required software
e. Electronic Stability Control shall be provided in compliance with NFPA 1901 Chapter
4.13.1.2 if the manufacturer cannot comply with Chapters 4.13.1.1 through 4.13.1.1.3.2.
f. Tire pressure monitoring system per Chapter 4.13.4
g. Chrome or stainless steel front bumper
h. Tow hooks or eyes front and rear attached to the frame
i. Front and rear mud flaps
j . S-cam air brakes or equivalent, as large as possible, with automatic slack adjusters
k. Minimum 13.2 cfm gear driven air compressor
1. Air dryer, turn drain valves on reservoirs
m. ABS brakes
n. Power steering with tilt/telescopic wheel, if available
2. POWERTRAIN
a. Minimum 330 horsepower turbocharged diesel engine, 850 lb. torque rating, minimum
b. Engine exhaust at front of right rear wheels
C. Secondary engine braking
d. Drivelines to meet engine torque rating
e. Automatic transmission
f. 50 gallon minimum fuel tank
g. OEM oil, fuel, transmission filters
TR 12430- Exhibit D
Base Specifications # 15 - Commercial Pumper
3. 2-DOOR CAB
a. Seating for two (2) - bucket style vinyl seats with NFPA compliant seat belts and seat belt
warning system
b. Console between seats for storage of radios, 12-volt switches, and maps/notebooks
C. Air conditioning and heating
d. Engine compartment light
e. Dome/step lights meeting NFPA 1901
f. Single tone cab paint finish with OEM standard paint warranty
g. Driver remote controlled mirrors with separate flat and convex sections
h. Dual type headlights
i. Forward facing turn and warning lights
j . Minimum two (2) under cab step lights
k. Cab and compartment door ajar light and buzzer
1. Engine compartment light
m. 270 amp alternator
n. Minimum two (2) 750 CCA batteries
o. Load manager with automatic high idle function
p. Dual air horns with dual in -cab controls
q. Receptacle near driver's door with onboard battery charger
4. LIGHTS AND SIRENS
a. NFPA compliant warning lighting package - manufacturer's standard package
b. Electronic 200 watt siren/PA with minimum 100 watt speaker recessed in bumper
5. BODY
a. Bidders to bid on each of their offered construction types:
• Extruded aluminum
• Formed aluminum
• Formed galvanneal steel
• Formed stainless steel
b. Bidders to state thicknesses, alloys and construction methods of all materials used in body
construction
C. Minimum of 3 compartments driver side of body, full height compartments
d. Minimum of 2 low side compartments right side of body
C. Lights in compartments to meet NFPA 1901 Chapter 13.10.5
f. One (1) full height, full depth compartment rear of body
g. Back up alarm
h. Right side brackets for 24' 2-section, 14' roof, 10' attic ladders and 2 pike poles, ladders to
be included
i. Hose bed with hose restraints to be NFPA compliant; including one (1) adjustable divider
j . Steps and handrails for climbing from ground to hose bed - bidders to state exact design
k. Lights at each step
1. Stop/turn/back up lights
m. DOT clearance and marker lights
n. License plate light
0. Two (2) rear deck lights
p. Rub rail along each side of body and rear of body
q. Running boards at each pump panel
TR 12430 Exhibit D
Base Specifications # 15 - Commercial Pumper
r. Brushed stainless steel or black non -glare aluminum pump panels
S. Hose bed lighting must be provided per NFPA 1901 Chapter 13.10.2
t. Minimum 4" reflective stripe on cab and body, chevron striping on rear of body per NFPA
1901
6. PUMP
a.
1250 gpm drive shaft driven split shaft pump per NFPA 1901 Chapter 16
b.
One 3" deck gun discharge
C.
Four 2.5" discharge outlets (includes one (1) rear 2-1 /2" discharge)
d.
One 2.5" suction inlet on left pump panel
e.
Two 6" steamer inlets with caps
f.
Discharge and inlet pressure reliefs
g.
Two 1.75" crosslays with 2" piping
h.
One 3" tank to pump line
i.
One 2" tank fill line
j .
30 degrees turn downs
k.
Anti -vibration gauges
1.
Color coded pump panel tags
m.
Stainless steel plumbing with 10-year warranty
n.
Side mount pump panel with all pump controls, instruments, and gauges located on the
driver side pump panel (not in a compartment)
0.
15 ft. of soft suction hose sized for capacity of fire pump
7. WATER TANK
a. 750-gallon T-type tank (U.S.) poly.
b. Lifetime warranty
C. 12" x 12" fill tower
8. COMPARTMENTS
a. Manufacturer will submit cubic feet and size of compartments per request
a. 1 year bumper to bumper mechanical, excluding normal wear and tear items
b. 10 year body structural
C. 10 year paint pro -rated on body
d. 10 year corrosion perforation on body
e. OEM Chassis manufacturer's standard warranty
f. 5 year fire pump warranty
g. Lifetime tank warranty
TR 12430- Exhibit D
FLORIDA
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 FREIGHTLINER M2
Specification # 15
(Commercial Pumper - 2 Door)
The Freightliner M2, Commercial Pumper, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
Crimson Star Pumper
$1981,057.00
Extruded Aluminum
Crimson Fire (Public Safety...)
E-ONE TDPM
$1709517.00
Extruded Aluminum
Hall -Mark Fire Apparatus (E-ONE)
FFA RP751 Pumper
$2081,373.00
Extruded Aluminum
Ferrara Fire Apparatus, Inc.
FSA Pumper 13
$2089,768.00
Extruded Aluminum
Rosenbauer South Dakota, LLC
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATIONOF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 INTERNATIONAL DURASTAR
Specification # 15
(Commercial Pumper - 2 Door)
The International Durastar, Commercial Pumper, purchased through this contract comes with all
the standard equipment as specified by the manufacturer for this model and FSA's base vehicle
specification(s) requirements which are included and made a part of this contract's vehicle base price
as awarded by manufacturer by specification.
MODEL: Crimson Star Pumper FFA RP751 Pumper
BASE PRICE: $1971,690.00 $206, 838.00
BODY: Extruded Aluminum Extruded Aluminum
MANUFACTURER: Crimson Fire (Public Safety...) Ferrara Fire Apparatus, Inc.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
E-ONE TDPM
$1769125,00
Extruded Aluminum
Hall -Mark Fire Apparatus
Sutphen C 1 Pumper
$2169792.00
Extruded Aluminum
Sutphen Corporation
FSA Pumper 13
$2109876.00
Extruded Aluminum
(E-ONE) Rosenbauer South Dakota, LLC
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION OF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA. ASSOCIATION OF COUNTIES
2012 FREIGHTLINER M2
Specification # 15
(Commercial Pumper - 2 Door)
The Freightliner M2, Commercial Pumper, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSKs base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL: American LaFrance S/M Pumper
BASE PRICE: $2129670.00
BODY: Formed Aluminum
MANUFACTURER: American LaFrance, LLC
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
KME Challenger FL15COML
$1999783.00
Formed Aluminum
Kovatch Mobile Equip. Corp. (KME)
FSA Pumper 13
$1821,408.00
Formed Aluminum
Rosenbauer South Dakota, LLC
Crimson Star Pumper
$1889773.00
Formed Aluminum
Crimson Fire (Public Safety...)
Pierce Contender Series
$1799598.00
Formed Aluminum
Pierce Manufacturing, Inc..
Toyne FFCSA Pumper
$2081,000.00
Formed Aluminum
Toyne, Inc. (Southeastern...)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
AS -SO IATIO Of
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 INTERNATIONAL DURASTAR
Specification # 15
(Commercial Pumper - 2 Door)
The International Durastar, Commercial Pumper, purchased through this contract comes with all
the standard equipment as specified by the manufacturer for this model and FSA's base vehicle
specification(s) requirements which are included and made a part of this contract's vehicle base price
as awarded by manufacturer by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
American LaFrance S/M Pumper
$2229246.00
Formed Aluminum
American LaFrance, LLC
KME Challenger FL15COML
$1971,654.00
Formed Aluminum
Kovatch Mobile Equip. Corp. (KME)
FSA Pumper 13
$184, 516.00
Formed Aluminum
Rosenbauer South
Dakota, LLC
Crimson Star Pumper
$1881,817.00
Formed Aluminum
Crimson Fire (Public Safety...)
Pierce Contender Series
$1849671.00
Formed Aluminum
Pierce Manufacturing, Inc.
Toyne FFCSA Pumper
$2139500.00
Formed Aluminum
Toyne, Inc. (Southeastern...)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for mobile water supply Chapter 7, FMVSS (applicable areas) and NHTSA standards, we
realize equipment needs and preferences are going to vary from agency to agency. Any options required
or changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FI.,ORIDA
ASSOCINTIONOF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 FREIGHTLINER M2
Specification # 15
(Commercial Pumper - 2 Door)
The Freightliner M2, Commercial Pumper, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
KME Challenger FL15COML
$1951,172.00
Formed Galvanneal Steel
Kovatch Mobile Equip. Corp. (KME)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
A SSOCIATION OF
COUNTIES
AU About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 INTERNATIONAL DURASTAR
Specification # 15
(Commercial Pumper - 2 Door)
The International Durastar, Commercial Pumper, purchased through this contract comes with all
the standard equipment as specified by the manufacturer for this model and FSA's base vehicle
specification(s) requirements which are included and made a part of this contract's vehicle base price
as awarded by manufacturer by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
KME Challenger FL15COML
$192, 712.00
Formed Galvanneal Steel
Kovatch Mobile Equip. Corp. (KME)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for mobile water supply Chapter 7, FMVSS (applicable areas) and NHTSA standards, we
realize equipment needs and preferences are going to vary from agency to agency. Any options required
or changes required by purchaser shall be made through the vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
A.Sso to rR.) OF
+COUNTIES
All About 141orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 FREIGHTLINER M2
Specification # 15
(Commercial Pumper - 2 Door)
The Freightliner M2, Commercial Pumper, purchased through this contract comes with all the standard
equipment as specified by the manufacturer for this model and FSA's base vehicle specification(s)
requirements which are included and made a part of this contract's vehicle base price as awarded by
manufacturer by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
American LaFrance S/M Pumper
$2131,763.00
Formed Stainless Steel
American LaFrance, LLC
E-ONE PSTS
$1999325.00
Formed Stainless Steel
Hall -Mark Fire Apparatus (E-ONE)
Toyne FFCSA Pumper
BASE PRICE: $2121,000.00
BODY: Formed Stainless Steel
MANUFACTURER: Toyne, Inc. (Southeastern...)
Crimson Star Pumper
$2009801.00
Formed Stainless Steel
Crimson Fire (Public Safety...)
KME Challenger FL 15COML
$2041,530,00
Formed Stainless Steel
Kovatch Mobile Equip. Corp. (KME)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options, required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add / delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCLATION OF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 INTERNATIONAL DURASTAR
Specification # 15
(Commercial Pumper - 2 Door)
The International Durastar, Commercial Pumper, purchased through this contract comes with all
the standard equipment as specified by the manufacturer for this model and FSKs base vehicle
specification(s) requirements which are included and made a part of this contract's vehicle base price
as awarded by manufacturer by specification.
MODEL:
BASE -PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
American LaFrance S/M Pumper
$22%902.00
Formed Stainless Steel
American LaFrance, LLC
E-ONE PSIS
$2059237.00
Formed Stainless Steel
Hall -Mark Fire Apparatus (E-ONE)
Toyne FFCSA Pumper
$2179500.00
Formed Stainless Steel
Toyne, Inc. (Southeastern...)
Crimson Star Pumper
$2029899.00
Formed Stainless Steel
Crimson Fire (Public Safety...)
KME Challenger FL15COML
$2029043.00
Formed Stainless Steel
Kovatch Mobile Equip. Corp. (KME)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION O
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
Base Specifications
SPECIFICATION #
i - LEVEL I C
M
ALL ITEMS FACTORY INSTALLED UNLESS OTHERWISE INDICATED
THE CUSTOM CAB AND CHASSIS SHALL BE PROVIDED BY THE BODY MANUFACTURER
1. CHASSIS
a. 110,000 psi heat treated steel frame rail system
b. 10 gauge polished stainless steel 16" to 24" extended front bumper with aluminum diamond
plate gravel shield
c. Tow hooks or eyes front and rear attached to the frame
d. 18,000 pound minimum front axle, suspension, tubeless radial tires, steel disc wheels
e. 24,000 pound minimum rear axle, suspension, tubeless radial tires, steel disc wheels
f. Front and rear mud flaps
g. NFPA 1901 Chapter 4.15.3 top speed rating requirement
h. S-cam air brakes or equivalent, as large as possible, with automatic slack adjusters
. Manufacturer's standard compressor
j . Minimum 4200 cubic inch air reservoir capacity
k. Air dryer, color coded air lines, turn drain valves on reservoirs
1. ABS brakes
m. Power steering with tilt/telescopic wheel
n. Vehicle data recorder (VDR) in compliance with Chapter 4.11 with required software meeting
4.11.8
0. Electronic Stability Control shall be provided in compliance with NFPA 1901 Chapter 4.13.1.2
if the manufacturer cannot comply with Chapters 4.13.1.1 through 4.13.1.1.3.2.
p. Tire pressure monitoring system with Chapter 4.13.4
2. POWERTRAIN
a. Minimum 350 horsepower turbocharged diesel engine with 1000 ft. lb. torque rating
b. Engine exhaust at front of right rear wheels
C. Secondary engine braking
d. Engine manufacturer's statement of engine installation approval with approved cooling system
e. Drivelines to meet engine torque rating
f. Silicone coolant hoses with constant torque clamps
g. Automatic transmission
TR 12430- Exhibit D
Base Specifications # 16 - Level I Custom Pumper
h. 50 gallon minimum fuel tank
i. OEM oil, fuel, transmission filters
3. CAB
a. Manufacturer's standard medium length tilt aluminum cab meeting NFPA 1901 Chapter
14.3.2
b. Seating for four, three in SCBA seats with SCBA brackets
c. Air ride driver seat, all others fixed position
d. All persons in 3-point seat belts per Chapter 14, seats equipped with seat belt/occupant
detection/warning system per Chapter 14
e. Electric over hydraulic cab tilt with manual back-up
f. Single tone cab paint finish with 10 year paint warranty pro -rated
g. Air conditioning and heating
h. Remote controlled mirrors (from driver's position) with separate flat and convex sections
i. DOT compliant headlights
j . Forward facing turn and warning lights
k. Cornering turn and warning lights
1. Minimum four (4) dome lights with red and clear bulbs
m. Minimum four (4) under cab step lights
n. Cab and compartment door ajar light and buzzer
o. One (1) engine compartment light
p. Color coded and function coded wiring
q. Alternator sized according to amp draw report
r. Minimum four (4) 750 CCA batteries
S. Load manager with automatic high idle function
t. Dual air horns with dual in -cab controls
4. LIGHTS AND SIRENS
a. NFPA compliant upper and lower level warning light package
b. Siren/PA - 200 watts
C. 100-watt speaker
d. Two rear deck lights
5. BODY
a. Bidders to bid on each of their offered construction types:
• Extruded aluminum
• Formed aluminum
• Formed galvanneal steel
• Formed stainless steel
b. Bidders to state thicknesses, alloys and construction methods of all materials used in body
construction
C. Minimum of 3 compartments driver side of body, full height compartments
d. Minimum of 2 low side compartments right side of body
e. Lights in compartments to meet NFPA 1901 Chapter 13.10.5
f. One (1) full height, full depth compartment rear of body
g. Back up alarm
h. Right side brackets for 24' 2-section, 14' roof, 10' attic ladders and 2 pike poles, ladders to
be included
i. Hose bed with hose restraints to be NFPA compliant; including one (1) adjustable divider
j . Steps and handrails for climbing from ground to hose bed - bidders to state exact design
TR 12430- Exhibit D
Base Specifications # 16 - Level I Custom Pumper
k. Lights at each step
1. Stop/turn/back up lights
m. DOT clearance and marker lights
n. License plate light
o. Two (2) rear deck lights
p. Rub rail along each side of body and rear of body
q. Running boards at each pump panel
r. Brushed stainless steel or black non -glare aluminum pump panels
S. Hose bed lighting must be provided per NFPA 1901 Chapter 13.10.2
t. Minimum 4" reflective stripe on cab and body, chevron striping on rear of body per NFPA
1901
6. PUMP
a. 1250 gpm drive shaft driven split shaft pump per NFPA 1901 Chapter 16
b. One 3" deck gun discharge
C. Four 2.5" discharge outlets (includes one (1) rear 2-1/2" discharge)
d. One 2.5" suction inlet on left pump panel
e. Two 6" steamer inlets with caps
f. Discharge and inlet pressure reliefs
g. Two 1.75" crosslays with 2" piping
h. One 3" tank to pump line
i. One 2" tank fill line
j . 30 degrees turn downs
k. Anti -vibration gauges
1. Color coded pump panel tags
m. Stainless steel plumbing with 10-year warranty
n. Side mount pump panel with all pump controls, instruments, and gauges located on the
drivers side pump panel (not in a compartment)
0. 15 ft. of soft suction hose sized for capacity of fire pump
7. WATER TANK
a. 750-gallon T-type tank (U.S.) poly.
b. Lifetime warranty
C. 12" x 12" fill tower
8. COMPARTMENTS
a. Manufacturer will submit cubic feet and size of compartments with bid.
a. 1 year bumper to bumper mechanical, excluding normal wear and tear items
b. 10 year cab and body structural
C. 10 year paint pro -rated
d. 10 year corrosion perforation on cab and body
e. Lifetime frame warranty
f. 2 year axle warranty
g. 5 year engine warranty
h. 5 year transmission warranty
i. 5 year fire pump warranty
j . Lifetime booster tank
TR 12430- Exhibit D
FLORIDA
ASSOCIATION OF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 LEVEL I CUSTOM PUMPER
Specification # 16
(Custom Chassis - 4 Door)
The Custom Pumper, purchased through this contract comes with all the standard equipment as
specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
E-One Typhoon Pumper
$2571,508.00
Extruded Aluminum
Hall -Mark Fire Apparatus (E-ONE)
S Series Custom
$3081,970.00
Extruded Aluminum
Sutphen Corporation
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FI,OR.IDA
ASSOCINTION OF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 LEVEL I CUSTOM PUMPER
Specification # 16
(Custom Chassis - 4 Door)
The Custom Pumper, purchased through this contract comes with all the standard equipment as
specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
KME Challenger FL 16LVL 1
$2739541.00
Formed Aluminum
Kovatch Mobile Equip. Corp. (KME)
S-Series Custom
$2901,993.00
Formed Aluminum
Sutphen Corporation
Pierce Saber Series
$2699266.00
Formed Aluminum
Pierce Manufacturing, Inc
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
F1, ASSOCIATION,
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 LEVEL I CUSTOM PUMPER
Specification # 16
(Custom Chassis - 4 Door)
The Custom Pumper, purchased through this contract comes with all the standard equipment as
specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL: KME Challenger FL 16LVL 1 Pierce Velocity SLT Series
BASE PRICE: $2689943.00 $3379573.00
BODY: Formed Galvanneal Steel Formed Galvanneal Steel
MANUFACTURER: Kovatch Mobile Equip. Corp. (KME) Pierce Manufacturing, Inc
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOC] 'ATIONKOF
COUNTIES
AU About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 LEVEL I CUSTOM PUMPER
Specification # 16
(Custom Chassis - 4 Door)
The Custom Pumper, purchased through this contract comes with all the standard equipment as
specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
E-ONE Typhoon Pumper
$2711,734.00
Formed Stainless Steel
Hall -Mark Fire Apparatus (E-ONE)
Pierce Impel SS Series
$3089890.00
Formed Stainless Steel
Pierce Manufacturing, Inc.
KME Challenger FL 1 6LVL 1
$2781,274.00
Formed Stainless Steel
Kovatch Mobile Equip. Corp. (KME)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed. .
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCTATI€.CNN OF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 LEVEL I CUSTOM PUMPER
Specification # 16
(Spartan Chassis - 4 Door)
The Custom Pumper, purchased through this contract comes with all the standard equipment as
specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL: Crimson Metro Star Pumper L1
BASE PRICE: $2691,507.00
BODY: Extruded Aluminum
MANUFACTURER: Crimson Fire (Public Safety... )
Spartan Force 16
$2729842.00
Extruded Aluminum
Rosenbauer South Dakota, LLC
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association.
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATIONOF
COUNTIES
All About 11orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 LEVEL I CUSTOM PUMPER
Specification # 16
(Spartan Chassis - 4 Door)
The Custom Pumper, purchased through this contract comes with all the standard equipment as
specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
Crimson Metro Star Pumper L 1
$260,656.00
Formed .Aluminum
Crimson Fire (Public Safety...}
Toyne Spartan Metro Star FFCSA
$2861,000.00
Formed Aluminum
Toyne, Inc. (Southeastern...)
Spartan Force 16
$2489128.00
Formed Aluminum
Rosenbauer South Dakota, LLC
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATIONTOF
COUNTIES
All About 141oreda
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 LEVEL I CUSTOM PUMPER
Specification # 16
(Spartan Chassis - 4 Door)
The Custom Pumper, purchased through this contract comes with all the standard equipment as
specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
Crimson Metro Star Pumper L1
$2721,159.00
Formed Stainless Steel
Crimson Fire (Public Safety... )
Toyne Spartan Metro Star FFCSA
$2901,250.00
Formed Stainless Steel
Toyne, Inc. (Southeastern... )
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters,. FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA.
ASSOCIATION OF
COUNTIES
All About 1�'orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 LEVEL I CUSTOM PUMPER
Specification # 16
(HME Chassis - 4 Door)
The Custom Pumper, purchased through this contract comes with all the standard equipment as
specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL: Intruder
BASE PRICE: $277, 618.00
BODY: Extruded Aluminum
MANUFACTURER: Ferrara Fire Apparatus, Inc.
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION OF`
CULYNTIES
All About Norida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 LEVEL I CUSTOM PUMPER
Specification # 16
(HME Chassis - 4 Door)
The Custom Pumper, purchased through this contract comes with all the standard equipment as
specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL: Toyne 1871W FFSCA
BASE PRICE: $2939500.00
BODY: Formed Aluminum
MANUFACTURER: Toyne, Inc. (Southeastern...)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION OF
COUNTIES
All About .Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 LEVEL I CUSTOM PUMPER
Specification # 16
(HME Chassis - 4 Door)
The Custom Pumper, purchased through this contract comes with all the standard equipment as
specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL: Toyne 1871 W FFSCA
BASE PRICE: $2979500,00
BODY: Formed Stainless Steel
MANUFACTURER: Toyne, Inc. (Southeastern...)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLOR.IDA.
ASSOCINTION OF
COUNTIES
Ali About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 LEVEL I CUSTOM PUMPER
Specification # 16
(American LaFrance Chassis - 4 Door)
The Custom Pumper, purchased through this contract comes with all the standard equipment as
specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL: American LaFrance Custom S/M Pumper
BASE PRICE: $3001,634.00
BODY: Formed Aluminum
MANUFACTURER: American LaFrance, LLC
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FI. OR.IDA.
ASSOCIATIONNOF
COUNTIS
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 LEVEL I CUSTOM PUMPER
Specification # 16
(American LaFrance Chassis - 4 Door)
The Custom Pumper, purchased through this contract comes with all the standard equipment as
specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL: American LaFrance Custom S/M Pumper
BASE PRICE: $3019992.00
BODY: Formed Stainless Steel
MANUFACTURER: American LaFrance, LLC
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and' other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION 01"
COUNTIES
Ate About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
Base Specifications
SPECIFICATION # 17 -LEVEL II CUSTOM
ALL ITEMS FACTORY INSTALLED UNLESS OTHERWISE INDICATED
THE CUSTOM CAB AND CHASSIS SHALL BE PROVIDED BY THE BODY MANUFACTURER
1. CHASSIS
a. 110,000 psi heat treated steel frame rail system
b. 10 gauge polished stainless steel 16" to 24" extended front bumper with aluminum diamond
plate gravel shield, 1-1 /2 front jump line with enclosed compartment in center of front bumper
to hold minimum 100' of 1-3/4 DJ fire hose
c. Tow hooks or eyes front and rear attached to the frame
d. 20,000 pound minimum front axle, suspension, tubeless radial tires, polished aluminum
wheels with hub and lug trim package
e. 24,000 pound minimum rear axle, suspension, tubeless radial tires, polished aluminum
wheels with hub and lug trim package
f. Front and rear mud flaps
g. NFPA 1901 Chapter 4.15.3 top speed rating requirement
h. S-cam air brakes or equivalent, as large as possible, with automatic slack adjusters
i. Manufacturer's standard compressor
j . Minimum 5000 cubic inch air reservoir capacity
k. Air dryer, color coded air lines, turn drain valves on reservoirs
1. ABS brakes
m. Power steering with tilt/telescopic wheel
n. Vehicle data recorder "R) in compliance with Chapter 4.11 with required software meeting
4.11.8
o. Electronic Stability Control shall be provided in compliance with NFPA 1901 Chapter 4.13.1.2
if the manufacturer cannot comply with Chapters 4.13.1.1 through 4.13.1.1.3.2.
p. Tire pressure monitoring system with Chapter 4.13.4
2. POWERTRAIN
a. Turbocharged diesel engine with a minimum 400 horsepower and 1450 ft. lbs. torque rating
b. Engine exhaust at front of right rear wheels
C. Secondary braking
TR 12430- Exhibit D
Base Specifications # 17 - Level H Custom Pumper
d. Engine manufacturer's statement of engine installation approval with approved cooling system
e. Drivelines to meet engine torque rating
f. Silicone coolant hoses with constant torque clamps
g. EVS 4000 or equivalent automatic transmission
h. 65 gallon minimum fuel tank
i. OEM oil, fuel, transmission filters
3. CAB
a. Extended length tilt aluminum cab (minimum 65" from center of front axle to rear of cab)
with minimum 10" raised rear roof meeting NFPA 1901 Chapter 14.3.2
b. Seating for six, five in SCBA seats with SCBA brackets
C. Air ride driver seat, all others fixed position
d. All persons in 3-point seat belts per Chapter 14, .seats equipped with seat belt/occupant
detection/warning system per Chapter 14
e. Electric over hydraulic cab tilt with manual back-up
f. Single tone cab paint finish with 10 year paint warranty pro -rated
g. Air conditioning and heating
h. Remote controlled mirrors (from driver's position) with separate flat and convex sections
i. DOT compliant headlights with LED marker and clearance lights
j . LED forward facing turn and warning lights
k. LED cornering turn and warning lights
1. Minimum four (4) dome lights with red and clear bulbs
m. Minimum four (4) under cab step lights
n. Cab and compartment door ajar light and buzzer
0. One (1) engine compartment light
p. Color coded and function coded wiring
q. Minimum 320 amp alternator
r. Minimum four (4) 750 CCA batteries
S. Load manager with automatic high idle function
t. Dual air horns with dual in -cab controls
4. LIGHTS AND SIRENS
a. NFPA LED compliant lighting package, upper and lower
b. Siren / PA - 200 watts
C. Mechanical siren with dual controls
d. Two 100-watt siren speakers
e. Two rear deck lights
f. 8kW hydraulic generator, 6-place breaker panel, (2) 750 watt telescopic lights mounted on
body
5. BODY
a. Bidders to bid on each of their offered construction types:
• Extruded aluminum
• Formed aluminum
• Formed galvanneal steel
• Formed stainless steel
b. Bidders to state thicknesses, alloys and construction methods of all materials used in body
construction
C. Three full height, full depth rescue style compartments on drivers side
TR 12430- Exhibit D
Base Specifications # 17 - Level H Custom Pumper
d. Three full height, full depth lower, half -depth upper rescue style compartments passenger
side of body
e. Lights in compartments to meet NFPA 1901 Chapter 13.10.5
f. One (1) full height, full depth compartment rear of body
g. Back up alarm
h. Internal ladder storage compartment right rear of body, to hold NFPA complement of ground
ladders and two (2) pike poles
i. Hose bed with hose restraints to be NFPA compliant; including one (1) adjustable divider;
minimum hosebed size of 70 cubic feet of usable storage
j . Steps and handrails for climbing from ground to hose bed - bidders to state exact design
k. Lights at each step
1. LED stop/turn/back up lights
m. LED DOT clearance and marker lights
n. LED license plate light
0. Minimum of 4 SCBA bottle storage compartments in rear wheel wells
p. Rub rail along each side of body with reflective stripe in rub rail
q. Running boards at each pump panel with a recessed hose well with hose restraint strap in
the passenger side running board
r. Brushed stainless steel or black non -glare aluminum pump panels
S. Hose bed lighting must be provided per NFPA 1901 Chapter 13.10.2
t. Minimum 4" reflective stripe on cab and body, chevron striping on rear of body per NFPA
1901
u. Four (4) aluminum adjustable shelves, located by customer
V. Two (2) floor mounted aluminum roll -out trays, minimum 250 lb. capacity each, located by
customer
w. Equipment package: One 10' folding attic ladder, one 14' roof ladder, one 24' 2-section
extension ladder, two 10' pike poles
6. PUMP
a.
1500 gpm drive shaft driven split shaft pump with side mount pump panel per NFPA 1901
Chapter 16
b.
One 3" deck gun discharge
C.
Four 2.5" discharge outlets (includes one (1) rear 2-1/2" discharge)
d.
One 2.5" suction inlet on left pump panel
e.
Two 6" steamer inlets with caps
f.
Discharge and inlet pressure reliefs
g.
Two 1.75" crosslays with 2" piping
h.
One 3" tank to pump line
i.
One 2" tank fill line
j.
30 degrees turn downs on all 2-1/2 99 or larger discharges
k.
Anti -vibration gauges
1.
Color coded pump panel tags
m.
Stainless steel plumbing with 10-year warranty
n.
One 4" LDH discharge, right side pump panel, hand wheel control with 4" discharge valve
and piping
7. WATER TANK
a. 750-gallon rectangular tank (U.S.) poly.
b. Lifetime warranty
C. 12" x 12" fill tower
TR 12430- Exhibit D
Base Specifications # 17 - Level H Custom Pumper
8. COMPARTMENTS
a. Manufacturer will submit cubic feet and size of compartments with bid.
a. 1 year bumper to bumper mechanical, excluding normal wear and tear items
b. 10 year cab and body structural
c. 10 year paint pro -rated
d. 10 year corrosion perforation on cab and body
e. Lifetime frame warranty
f. 2 year axle warranty
g. 5 year engine warranty
h. 5 year transmission warranty
i. 5 year fire pump warranty
j . Lifetime booster tank
a
TR 12430- Exhibit D
FLORIDA
ASSO I ATION OF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 LEVEL II CUSTOM PUMPER
Specification # 17
(Custom Chassis - 4 Door)
The Custom Pumper, purchased through this contract comes with all the standard equipment as
specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
Igniter XD LFD
$3991,874.00
Extruded Aluminum
Ferrara Fire Apparatus, Inc.
Commander FSA 17
$364, 916.00
Extruded Aluminum
Rosenbauer South Dakota, LLC
E-ONE Cyclone Pumper
$3731,084.00
Extruded Aluminum
Hall -Mark Fire Apparatus (E-ONE)
Monarch Series Custom
$4219112.00
Extruded Aluminum
Sutphen Corporation
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by -purchaser shall be made through the
vendor listed.
Purchasers are advised that the e
unit only. The Florida Fire Chiefs'
of Counties have identified and ei
items required to meet all currer
vary from agency to agency, any
by the purchaser shall be made
bove referenced vehicle specification comes equipped as a' base
Association, Florida Sheriffs Association and Florida Association
juipped the base unit with those specifications and equipment
t NFPA. Since equipment needs and preferences are going to
additional options required or changes to the base unit desired
through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCLATIONOF
COUNTIES
AU About Norida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 LEVEL II CUSTOM PUMPER
Specification # 17
(Custom Chassis - 4 Door)
The Custom Pumper, purchased through this contract comes with all the standard equipment as
specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
KME Flatback FL 17LVL2
$3579181.00
Formed Aluminum
Kovatch Mobile Equip. Corp. (KME)
Commander FSA 17
$3409030.00
Formed Aluminum
Rosenbauer South Dakota, LLC
Pierce Arrow KT Series
$3879678.00
Formed Aluminum
Pierce Manufacturing, Inc.
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATION OF
COUNTIES
All About 11orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 LEVEL II CUSTOM PUMPER
Specification # 17
(Custom Chassis - 4 Door)
The Custom Pumper, purchased through this contract comes with all the standard equipment as
specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
KME Flatback FL 17LVL2
$3529582.00
Formed Galvanneal Steel
Kovatch Mobile Equip. Corp. (KME)
Pierce Quantum Series
$395, 482.00
Formed Galvanneal Steel
Pierce Manufacturing, Inc.
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCLATIONTOF
COUNTIES
All About 11or°ida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8t FLORIDA ASSOCIATION OF COUNTIES
2012 LEVEL II CUSTOM PUMPER
Specification # 17
(Custom Chassis - 4 Door)
The Custom Pumper, purchased through this contract comes with all the standard equipment as
specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
E-ONE Cyclone Pumper
$3941151.00
Formed Stainless Steel
Hall -Mark Fire Apparatus (E-ONE)
Pierce Velocity Series
$3999974.00
Formed Stainless Steel
Pierce Manufacturing, Inc.
KME Flatback FL 17LVL2
$3619913,00
Formed Stainless Steel
Kovatch Mobile Equip. Corp. (KME)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCI R rioN OF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 LEVEL II CUSTOM PUMPER
Specification # 17
(Spartan Chassis - 4 Door)
The Custom Pumper, purchased through this contract comes with all the standard equipment as
specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
Crimson Metro Star Pumper L2
$3661,042.00
Extruded Aluminum
Crimson Fire (Public Safety... )
Spartan Gladiator 17
$3739656.00
Extruded Aluminum
Rosenbauer South Dakota, LLC
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCINTION OF
COUNTIES
AU About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 LEVEL II CUSTOM PUMPER
Specification # 17
(Spartan Chassis - 4 Door)
The Custom Pumper, purchased through this contract comes with all the standard equipment as
specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
Crimson Metro Star Pumper L2
$3411,025.00
Formed Aluminum
Crimson Fire (Public Safety...)
Toyne Spartan Gladiator
$3779000.00
Formed Aluminum
Toyne, Inc. (Southeastern...)
Spartan Gladiator 17
$3461,660.00
Formed Aluminum
Rosenbauer South Dakota, LLC
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes. equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA.
ASS'00 A.TIO'N OF
COUNTIES
AU About 141orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 LEVEL II CUSTOM PUMPER
Specification # 17
(Spartan Chassis - 4 Door)
The Custom Pumper, purchased through this contract comes with all the standard equipment as
specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL: Crimson Metro Star Pumper L2 Toyne Spartan Gladiator
BASE PRICE: $3681,450.00 $3811,000.00
BODY: Formed Stainless Steel Formed Stainless Steel
MANUFACTURER: Crimson Fire (Public Safety...) Toyne, Inc. (Southeastern...)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCIATIOIN OF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 LEVEL II CUSTOM PUMPER
Specification # 17
(HME Chassis - 4 Door)
The Custom Pumper, purchased through this contract comes with all the standard equipment as
specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL: Spectr LFD
BASE PRICE: $3861,017.00
BODY: Extruded Aluminum
MANUFACTURER: Ferrara Fire Apparatus, Inc.
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
LjFCw�^(�{L■/ OR�jIDAON F
COUNTIES
All About Norida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 LEVEL II CUSTOM PUMPER
Specification # 17
(HME Chassis - 4 Door)
The Custom Pumper, purchased through this contract comes with all the standard equipment as
specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL: Toyne Spectr
BASE PRICE: $3799000.00
BODY: Formed Aluminum
MANUFACTURER: Toyne, Inc. (Southeastern...)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FEORIDA
ASSOCLATIOIN OF
COUNTIES
All About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 LEVEL II CUSTOM PUMPER
Specification # 17
(HME Chassis - 4 Door)
The Custom Pumper, purchased through this contract comes with all the standard equipment as
specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL:
BASE PRICE:
BODY:
MANUFACTURER:
Toyne Spectr
$3839000.00
Formed Stainless Steel
Toyne, Inc. (Southeastern...)
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA.
ASSOCIATION OF
COUNTIES
AU About Florida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
& FLORIDA ASSOCIATION OF COUNTIES
2012 LEVEL II CUSTOM PUMPER
Specification # 17
(American LaFrance Chassis - 4 Door)
The Custom Pumper, purchased through this contract comes with all the standard equipment as
specified by the manufacturer for this model and FSA's base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL: American LaFrance Custom Rescue Pumper
BASE PRICE: $3541,804.00
BODY: Formed Aluminum
MANUFACTURER: American LaFrance, LLC
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the above referenced vehicle specification comes equipped as a base
unit only. The Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association
of Counties have identified and equipped the base unit with those specifications and equipment
items required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base unit desired
by the purchaser shall be made through the manufacturer listed.
NOTE: An official listing of all add/delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
FLORIDA
ASSOCLATIONOF
COUNTIES
All About 141orida
FLORIDA FIRE CHIEFS' ASSOCIATION,
FLORIDA SHERIFFS ASSOCIATION
8c FLORIDA ASSOCIATION OF COUNTIES
2012 LEVEL II CUSTOM PUMPER
Specification # 1&
(American LaFrance Chassis - 4 Door)
The Custom Pumper, purchased through this contract comes with all the standard equipment as
specified by the manufacturer for this model and FSNs base vehicle specification(s) requirements
which are included and made a part of this contract's vehicle base price as awarded by manufacturer
by specification.
MODEL: American LaFrance Custom Rescue Pumper
BASE PRICE: $356J62.00
BODY: Formed Stainless Steel
MANUFACTURER: American LaFrance, LLC
While the Florida Fire Chiefs' Association, Florida Sheriffs Association and Florida Association of
Counties have attempted to identify equipment required to meet all current NFPA 1901, (2009 edition),
applicable for pumper fire apparatus Chapter 5 and other required chapters, FMVSS (applicable
areas) and NHTSA standards, we realize equipment needs and preferences are going to vary from
agency to agency. Any options required or changes required by purchaser shall be made through the
vendor listed.
Purchasers are advised that the
unit only. The Florida Fire Chiefs'
of Counties have identified and e
item
Bove referenced vehicle specification comes equipped as a base
Association, Florida Sheriffs Association and Florida Association
luipped the base unit with those specifications and equipment
s required to meet all current NFPA. Since equipment needs and preferences are going to
vary from agency to agency, any additional options required or changes to the base WELL desired
by the purchaser shall be made through the manufacturer I listed.
NOTE: An official listing of all add / delete options and their prices should be obtained from the
appropriate vendor.
TR 12430- Exhibit D
MUNICIPAL LEASE PROGRAM
Mears Leasing offers the broadest range of lease plans A Financial5ervice of
available in today's market! We offer Both Municipal Financing The Bancoirpank
($1.00 Buyout) and Closed -End Lease Plans (which allow you to
return the vehicle at lease end). Our closed -end lease plans are ideal for
administrative use or surveillance use. We will cater the lease requirements to meet
your mission needs! Whether you are looking for one vehicle or one -hundred
vehicles, we have the expertise and the financial stability to assist you.
• Marked Patrol Vehicles • Administrative Vehicles • Undercover Vehicles
• Sedans, Pick up Trucks, SUV's, Vans, SWAT Trucks, Buses, Fire Engines and all
Emergency Response Vehicles
• Over 50 YEARS EXPERIENCE in Municipal Finance/Leasing and Fleet Leasing
• No Fleet or equipment order too small!
Department Name:
Fleet Manager or POC:
Address:
Phone:
Fax:
How many total vehicles are in your fleet?:
Do you presently own or lease your vehicles?:
How often do you rotate your fleet?:
Do you lease surveillance or administrative vehicles?:
MEARS MOTOR
LEASING - 3905
El Rey Road
—Orlando, FL 32808 Call Us at
David Pickard
Joanne
Cornier
Bob Crowe
407-253-4462
dpickard@mearsleasing.com
407-253-4450
jcornier@mearsleasing.com
407M253-4469
bcrowe@mearsleasing.com
tE h: bit D'
Specializing in
Government Fleets.
With Enterprise Fleet Management, you'll benefit from full-time professionals implementing
solutions for your transportation needs. Enterprise provides services that are an asset for the
Florida •
Local Services
Enterprise provides value -oriented fleet management
solutions to help lower fleet costs. We enable you to
lower your costs in the areas of fleet management and
help bridge your capital budgets to your capital needs.
Vehicle Acquisition
Our new vehicle selection may provide a wider choice
than is available through the State.
Funding Programs
With our Municipal Lease or Lease Purchase, we
can give you the flexibility of your owned fleet while
providing a consistent way of cycling your vehicles at
their best economic point. Our flexibility enables you
to pay only for your use of the vehicle.
For more e following
�t � ,� .� ♦ ai rM
02011 Enterprise Fleet Management, Inc. C0114. 7 9/11 MJ
Maintenance Programs
By utilizing fixed cost for maintaining some of your
light -duty vehicles, we allow you to focus on your core
service needs. We fix the cost of maintaining your
fleet needs.
Customized Programs
Working Fleets -Public Works
Administrative Fleets
Law Enforcement
Pool Fleets
Virtual Fleets
WeCar Direct:
Online Reservations
Automated Key Dispenser
Mobile Resource Manager
Fuel Card
Enterprise stands ready to compete with what we
believe is the best value for your transportation needs.
11
fleet management
TR 12430- Exhibit E
Florida Sherriff's Association Contract # 11-10-1202
International 430OLP Medium Duty Ambulance Base Price 201,260
Installed options per Tamarac Fire Rescue Specifications
Chassis upgrades
21,456
Chrome Turnout for vertical exhaust
152
Front and rear heavy duty sway bars
11384
Energy Absorbing rear step
911
Fuel Tank covers with compartment
41696
Reverse Camera, including turn signal cameras
29294
Echo Vision rear collision avoidance system
525
Crossfire Dual tire pressure monitor
367
Bumper Wands
232
Custom 177" body
12000
ZICO electric 02 lift
21692
Exterior Compartment modifications
31676
Slide out SCBA storage tray
450
SCBA bottle tube holders
11800
Headroom Increase
740
Body Molding delete
307
Dri-Deck in all exterior compartments
425
Programmable touch pads (2)
19162
Recessed License plate bracket
142
Paint scheme per Tamarac Fire Rescue requirements
21240
Stainless Steel risers streetside
197
Stainless Steel risers curbside
197
Stainless steel lower door panels
275
Linen cabinet with heat/ac unit in bottom
19346
Pull out drawers in main wall cabinet
812
Custom CPR seat cabinet
650
Custom Squad Bench
11110
Cargo Net
450
Reinforce floor for future install of Power Load
750
Upgraded Federal EQ2B siren
19532
Upgraded led lighting
2,779
Rear Docking Lights
319
RemoteControl Go light
414
Pioneer LED Scene Lights
2,390
IPLEX panel in Cab dash
250
Max Cool Air Conditioner
11380
Upgraded LED dome lights
1,896
Wireless Firecom Intercom System
51900
GTT GPS style Opticom system
31400
Lettering to match current fleet
3,500
Total options 76,198
Total cost including options 277,458
Proposal subtotal 2773458
Less Hall -Mark Fire Discount 21000
Less Horton Discount 23000
Final proposal to customer 273 458